Digital Signal Processor
A microprocessor specifically intended for digital signal processing applications, generally in real-time.
-
product
MXG X-Series Microwave Analog Signal Generator, 9 kHz to 40 GHz
N5183B
Get a fast, compact (2U) alternative to the PSG in the lab, depot or fieldAddress demanding tests of radar modules & systems with near-PSG levels of spectral purityCompensate for system loss & drive high-power amplifiers: +19 dBm output power, -55 dBc harmonics & -68 dBc spurious @ 20 GHzReduce calibration time with switching speed 600 sSimulate narrowband chirps & radar antenna scans with up to five internal function generators that can be used with AM, FM, OM pulse modulation
-
product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
product
PCIe-4065, PCI Express, 6½-Digit, ±300 V Digital Multimeter Device
779771-01
The PCIe‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
product
PXIe 16 Bit High Speed Digitizer - 180 MS/s on 4 Channels
M4X.4471-X4
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
product
PCI-4065, 6½-Digit, ±300 V, PCI Digital Multimeter Device
779770-01
The PCI‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels
M4I.4470-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PXIe-5645, 6 GHz, 80 MHz Bandwidth, RF and Baseband PXI Vector Signal Transceiver
782377-01
6 GHz, 80 MHz Bandwidth, RF and Baseband PXI Vector Signal Transceiver—The PXIe‑5645 combines a vector signal generator and vector signal analyzer with FPGA-based real-time signal processing and control into a single device, also known as a VST. Because of this software-designed approach, the PXIe‑5645 offers the flexibility of a software defined radio architecture with RF instrument class performance. The PXIe‑5645 features a high-performance, differential or single-ended baseband I/Q interface. This interface allows the PXIe‑5645 to address many additional applications, such as testing both the upconverted RF and downconverted baseband signals of a device with a single instrument.
-
product
PCIe Digital Waveform Acquisition with Programmable Threshold - 250 MBit/s Internal Sampling Rate Timing, 250 MBit/S External State Clock
M4I.7720-X8
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
product
PXIe-5745, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Signal Generator
785597-01
The PXIe-5745 enables direct RF generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s for generation up to 1.5 GHz or in a single-channel wideband upconversion mode at 6.4 GS/s. The PXIe-5745 is ideal for applications that require high channel density IF signal generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for generating predefined waveforms, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA for dynamically creating waveforms, signal modulation/demodulation, and other custom real-time signal processing.
-
product
Real-Time Analysis up to 255 MHz, Basic Detection, Multi-touch
N9041B-RT1
See, capture, and understand elusive signals as short as 17.17 s with 100% POI and a complete set of advanced triggers, up to 110 GHz View signal dynamics with integrated real-time displays Maximize your investment by adding RTSA at a fraction of the cost of a dedicated solution Easily integrate the 89600 VSA software and thoroughly analyze complex signals Industry-leading 3 year warranty Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
PXI FlexRay Digitizer
PXD7113
The PXD7113 FlexRay Digitizer features a 100MS/s input with 16Bit resolution, input voltages up to ±10V and a bandwidth up to 10MHz. The PXD7113 FleyRay Digitizer has a 2MB memory which allows up to1 million samples. The device has a high common mode rejection ratio (CMRR).
-
product
PXI-6508, 96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module
777598-01
96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module—The PXI‑6508 uses four, 24‑bit programmable peripheral interfaces (PPIs) that can each be divided into three, 8‑bit ports. The PXI‑6508 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment. The PXI‑6508 is well suited for applications that require onboard pull-up resistors.
-
product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781775-01
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
product
PXIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.25 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4X.2223-X4
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
SHC68-C68-D4, 68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - 1m
196275-01
The SHC68-C68-D4, 1m, Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
product
Phi6 Drivers
Phi6 is the software environment to manage, control and program 6TL modules and systems.
-
product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110128
Primary mating contact 610110129. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BeCuContact Plating 50µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.41
-
product
80 I/O Multifunction Module
YAV90832
16 Analog Inputs 0…15Vdc 10 Bits Zin= 1,2MOhm 24 Digital Inputs (Trigger) 32 Digital Outputs 11…45V/650mA 4 Analog Outputs 0…10Vdc 10 Bits 4 Outputs PWM CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Signal, Patchcord, Receiver, 36", QuadraPaddle, 22 AWG Twisted Pair, Single Ended ( 5 Amps)
7-124422000-036
Signal, Patchcord, Receiver, 36", QuadraPaddle, 22 AWG Twisted Pair, Single Ended ( 5 Amps).
-
product
32-CH DI & 32-CH DO 12 MB/s High-Speed Card
PCIe-7200
- x1 lane PCI Express interface- 32-CH TTL digital inputs and 32-CH TTL digital outputs- Up to 12 MB/s transfer rate- Onboard programmable timer pacer clock- Support handshaking digital I/O transfer mode- Bus-mastering DMA for both digital inputs and outputs- 5 V power available on connectors- Compact, half-size PCB
-
product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785650-01
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
product
PCIe 12-Bit, 6 GS/s, Gen3 Digitizer
EON Express CompuScope
The GaGe EON Express CompuScope PCIe Gen3 digitizer board features unprecedented speed and resolution in a 6 GS/s streaming digitizer with 1.75 GHz bandwidth and PCIe data streaming rates up to 6 GB/s.
-
product
Multi Channel Waveform Acquisition and Spectrometer Card
Pixie Hybrid
The Pixie Hybrid is a multi channel all-digital waveform acquisition and spectrometer card. It provides a compact, fully featured solution to a variety of data acquisition needs.
-
product
16-Bit Digitizer
PA72D16180A
The PA72D16180A is a 16-bit digitizer, capable of capturing waveforms at speeds up to 180Msps. An onboard offset voltage source allows capturing offset signals while still using the optimal range for maximum ADC utilization. Two onboard filters allow suppression of out-of-band noise. The 64MWord onboard memory enables capturing very long waveforms, or sequentially capturing multiple signals with minimal intermediate bus communication.
-
product
RF Digitizer With 6.5 GHz Bandwidth
ADQ7WB
ADQ7WB is an RF digitizer with an analog input bandwidth of 6.5 GHz. It supports highly linear wideband data capture, and utilize Teledyne SP Devices' proprietary ADX technology in order to ensure industry-leading spurious-free dynamic range (SFDR).
-
product
PXI Breadboard Module, 2-Slot, 20-Pin GMCT
40-220A-802
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
PXIe Semi-Dynamic Digital I/O Module, 64-Channel
42-419-001
The 40-419-001 (PXI) and 42-419-001 (PXIe) are a 64-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
Vector Signal Generator
SMBV100B
The state-of-the-art R&S®SMBV100B vector signal generator sets standards for its class. Ultra high output power, fully calibrated wideband signal generation and intuitive touchscreen operation make the R&S®SMBV100B ideal for all kinds of applications.Always in line with the latest major digital communications standards, such as 5G NR, LTE and WLAN, the SMBV100B is the preferred test solution for receiver and component characterization.The R&S®SMBV100B has many GNSS options that transform the instrument into a reliable, full-featured GNSS simulator. Advanced simulation capabilities can run realistic and complex yet repeatable GNSS scenarios under controlled conditions.
-
product
NI-9421 , 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
779136-01
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.825-04
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
