Stepper Motors
A device that translates electrical pulses into precise mechanical movement. The output shaft may deliver rotary or linear motion. (www.seanet.com)
-
Product
Laser Spectroscopic Motor Exhaust Gas Analyzer
MEXA-ONE IRLAM
-
The MEXA-ONE IRLAM is an analyzer for the direct, simultaneous real-time measurement of the four relevant nitrogen-containing exhaust gas components NO, NO2, N2O and NH3.HORIBA's innovative infrared gas analysis technology, IRLAM™ (Infrared Laser Absorption Modulation), enables low-noise, high-precision measurement of four nitrogen compound gases (NO, NO2, N2O, NH3) in the low concentration range.
-
Product
Fully Automatic No Load ( Routine) Testing Panel For Self Priming Motors
-
Aarohi Embedded Systems Pvt. Ltd
Aarohi introduced fully automatic routine testing panel. The primary purpose of the routine test is to insure freedom from electrical and mechanical defects, and to demonstrate by means of key tests the similarity of the motor to a “standard” motor of the same design. this panel also help to enhance productivity, Work efficiency & reduces need for skill operator.
-
Product
4-Axis Stepping And Servo Motor Control Universal PCI Card
PCI-1240U
-
Independent 4-axis motion controlHand wheel and jog function2/3-axis linear interpolation function2-axis circular interpolation functionContinuous interpolation functionProgrammable T/S-curve acceleration/deceleration rateUp to 4 MPPS output for each axisTwo pulse output types: CW/CCW or Pulse/DirectionUp to 1 MHz encoder input for each axisTwo encoder pulse input types: A/B phase or Up/DownConstant speed controlPosition management and software limit switch functionBoardID™ switch
-
Product
Terminal Board With 100-Pin SCSI-II Connector For General Purpose Servo & Stepper
DIN-825-4P0
Terminal Board
- Supports specific servos & steppers by cable selecting- On-board connector type: 100-pin SCSI-II- Dimensions: 300 mm x 107 mm x 44 mm (W x L x H)
-
Product
Digital Roller Brake Tester for Cars and Vans up wot 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,200 mm
C_MBT C 3.5 W220 | VP 210152
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes.
-
Product
Electric Servo Motor Type Tension and Compression Tester
-
It is a tensile / compression fatigue / durability / performance tester for various materials and automotive parts that have an ultra low inertia AC servomotor mounted on the actuator.
-
Product
Electric Servo Motor Type Power Circulation Type Rotary Torquer Tester
-
Tests For Clutches Durability, Torque Converters, Transmissions, Differential Gears, CVJs, Etc. Can Be Performed At Low Cost By The Load Using The Power Circulation System.
-
Product
Control Board for Motor, Pump & Valve
F1V04
-
Beijing SANKI Petroleum Technology Co., Ltd.
The main board issues a start signal and a low voltage signal (12v) for opening the electromagnetic valve, which are converted into strong voltage signals (220 VAC) to drive the electromagnetic valve (380 VAC) and the motor in our fuel dispensers system, thus completing the function of conversion from weak voltage power to strong voltage power. The control board circuit isolates high voltage interference signals via photoelectrical isolating components.
-
Product
Direct Drive Motors
-
The Javelin Series enables OEMs to design high performance, reliable, small and lightweight systems using flexible and easy-to-integrate linear motor components. The Javelin Series’ state-of-the art magnetic designs deliver high acceleration and high speeds in compact form factors. Direct drive technology and air core (ironless) construction provide good mechanical stiffness, low cogging and zero backlash, reducing settling times and increasing system performance and throughput.
-
Product
HDD Motor Testers
BK8015/BK8015A
-
The BK8015 HDD Mechanical Specifications Tester and the BK8015A HDD Circuit Specifications Tester were designed and manufactured by BaKo to test HDD motors as they come off the assembly line. The two machines are complementary, and were designed to test a complete set of HDD motor characteristics.
-
Product
Safety Rated Servo Motors And Drives
-
Advanced motion safety functions including SLS, SLP and SS2 allow to complete a risk reduction strategy, and reduction in machine downtime while improving maintenance and changeover efficiency.
-
Product
Exacting Electric Motor Testing
-
The Taylor Dynamometer Electric Motor Test Stand is designed to provide maximum reliability, excellent durability and flawless performance. Using our extensive line of Water Brake engine dynamometers, Taylor Dynamometer has systems available for testing electric motors from 5 to 13,000 hp (3.7 to 9,694 kW). Include an instrumentation package to achieve your testing requirements. From simple speed, torque and power display systems with manual control to completely automated testing solutions, Taylor Dynamometer has a system to meet your testing requirements.
-
Product
Motor Test for Stepping Motors
-
*Stable measurement: Since it uses Prony braking, this model provides stable measurement unaffected by moments of inertia and no coupling loss. In addition, the resulting measurements allow data correlation via the traditional double-balance method.*Precision measurement method: This model’s judgment of synchronization loss achieves high stability using algorithms developed by Sugawara Laboratories. Measurement mode can be chosen based on step angle. For pull-in torque, startup can be measured consistently from the holding state. Allows measurement at 1-Hz resolution.*Broad measurement range: This model offers a range of seven available measurement heads, from 0.5 N to 50 N, allowing use for high-precision measurements. Through selection and use of pulleys, this model can also be used to measure small motors of 0.5 mN·m or less or 500 mN·m motors. Pulley diameters and other settings are easily configured using a personal computer running Windows®. Note: Any of the seven available heads may be attached to a single measurement component.*High-visibility measurement data: Motor characteristics are easily ascertained on automatically plotted performance graphs. Measurement data can be overlaid up to four times. In addition, the cursor can be used to read accurate values from measurement points. Hard copies of data displayed on-screen can be printed from a personal computer.*Can be controlled using standard personal computers: Allows control of measurement operations and display and storage of data from a standard personal computer running Windows®. Data is stored in CSV-format files for compatibility with other software applications.
-
Product
Development Test Stands for Electric Motors
-
Development test stands from imc are characterized by high flexibility in electric motor trials. A comprehensive variety of motor types can be tested and a complete range of tests carried out. The mechanical configuration consists of a test bed with a load machine and a torque measuring shaft. The load machine and torque sensor shaft are mounted on a linear guide and precisely aligned axially by means of laser. It can be moved towards the test object on ball bearings, as a complete unit. Especially time-saving: no need to realign the load machine assembly when changing the torque sensor.
-
Product
Traction and Induction Motor Test Systems
-
Crest makes state-of-the art test systems for testing 3-phase AC motors used in traction and other industrial applications.
-
Product
Motor Stator Test System
Chroma 1920
-
Chroma Systems Solutions, Inc.
For electrical safety and quality testing functions of motor stator coils
-
-
Product
Motor&Phase Rotation Indicator
-
Precision Mastech Enterprises Co.
A diagnostic tool used to identify the sequence or \(A,B,C\)) of a 3-phase power supply and determine the proper direction of rotation for 3-phase motors.
-
Product
Motor Control
-
A product portfolio that offers motor drivers (brushed, brushless, stepper, load & relay) and integrated motor control systems for all your motor control solutions.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,200mm
C_MBT C 4.0 W220 | VP 210156
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and Vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes with high vehicle throughput and increased loads.
-
Product
Dynamic Electric Motor Analyzers
-
Baker's dynamic motor test and monitoring instruments are built to conduct condition monitoring tests of motors and generators from a Motor Control Centre (MCC), or through a Baker EP1000 connection unit. The Baker EXP4000 dynamic motor analyser is a low-voltage, AC- and battery-operated instrument that test motors and generators while they are in operation. The EXP4000 provides health and performance data on the motor, the motor's load, and incoming power to assess motor performance and suitability in context of the entire machine system it supports.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 4.0 W250 | VP 210157
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans, and with high vehicle throughput and increased loads.
