GHz
See Also: Gigahertz, GHz Synthesizers
-
Product
PCIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2220-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 67 GHz, 50 Ω, SMA-1.85, Terminated, Remote Mount, Failsafe
42-785C-572-TE
Multiplexer Module
The 40-785C-572-TE (PXI) and 42-785C-572-TE (PXIe) are dual failsafe SP6T 67 GHz with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
Waveguide Harmonic Mixer, 18 to 26.5 GHz
11970K
Harmonic Mixer
The Keysight 11970K waveguide mixer is a general-purpose harmonic mixer employing a dual-diode design to achieve flat frequency response and low conversion loss. These are achieved without external dc bias or tuning stubs. Manual operation and computer-controlled hardware operation are simplified because mixer bias and tuning adjustment are not required.
-
Product
Modulation Distortion Up To 70 GHz
S930707B
-
S930707B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 70 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930707B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Near Field Probes 1GHz - 10 GHz
SX set
-
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Multi-Channel Attenuation Control Unit (4-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7204B
Attenuator
The J7204B is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204B reduces cost of ownership and provide the best measurement accuracy.
-
Product
Oscilloscope 80 GHz, 2 Channels
UXR0802B
Oscilloscope
The UXR0802B is the 80 GHz, 2 Channel, UXR-Series Real-Time Infiniium Oscilloscope.
-
Product
Solid State PIN Diode Transfer Switch, 100 MHz to 8 GHz
P9400A
Dual Transfer Switch
The Keysight P9400A solid state PIN diode transfer switch offers outstanding performance in terms of port-to-port isolation, switching speed and low insertion loss over a broad operating frequency range of 100 MHz to 8 GHz. The P9400A is particularly well-suited for ultra-fast RF and microwave switching applications in instrumentation, communications, radar, switch matrices and various other test systems where high isolation, speed and lifetime of a switch are critical.
-
Product
EXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5172B
Vector Signal Generator
Achieve faster throughput and greater uptime with cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading ACPR, EVM, and output powerReduce the time you spend on signal creation with Signal Studio software; purchase only the waveforms you need with 5- and 50-pack licensingMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
Product
Multiport Coaxial Switch, DC To 20 GHz, SP6T
L7106B
Coaxial Switch
Improve signal accuracy with this terminated switch that provides unmatched isolation, typically 90 dB at 12 GHz.
-
Product
Streamline Vector Network Analyzer, 100 KHz To 32 GHz, 4-port
P5026B
Vector Network Analyzer
Compact, faceless, vector network analyzer (VNA). Flexible four-port VNA dramatically reduces your size of test. Up to 32 GHz.
-
Product
8 GHz Differential Probe with ProBus2 Interface
DH08-PB2
Differential Probe
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 18 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-785C-421-E
Multiplexer Module
The 40-785C-421-E (PXI) and 42-785C-421-E (PXIe) are single failsafe SP4T 18 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI Vector Network Analyzer, 9 kHz to 9 GHz
M9802A
Vector Network Analyzer
Full 2/4/6/ port VNA on a PXI module with flexible applications.
-
Product
1 GHz A/D and D/A with Virtex-7 FPGA - 6U VPX
Model 57730
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1 GHz 12-bit A/D- One or two 1 GHz 16-bit D/A- 4 or 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 2 Channels, 2.5 GS.s on 4 Channels, 1.25 GS.s on 8 Channels, 1.5 GHz Bandwidth
DN2.225-08
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
Infiniium EXR-Series Oscilloscope: 6 GHz, 4 Channels
EXR604A
Oscilloscope
6 GHz on all 4 channels, 8 instruments integrated in one, hardware accelerated plotting, and fully upgradeable to 8 channels.
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7–16 (male)
85038M
Mechanical Calibration Kit
Modern wireless communication systems require high-performance components offering low VSWR and low intermodulation distortion at high transmit power levels. To meet these needs, 7-16 connectors are becoming increasingly common in base station transmitters, amplifiers, duplexers, and other products. These connectors conform to IEC 169-4, DIN 47223, European standard EN 122190, and British standard BSEN 122190.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 8 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
42-788-111-E
Multiplexer Module
The 40-788-111-E (PXI) and 42-788-111-E (PXIe) are single failsafe SP10T 8 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
Active Probe, 2 GHz
N2796A
General Purpose Probe
The N2796A is a new generation of low-cost, single-ended active probe with the AutoProbe interface. The probe integrates many of the characteristics needed for today’s general-purpose, high-speed probing - especially in digital system design, component design/characterization, and educational research applications. Its 1MΩ input resistance and extremely low input capacitance (1 pF) provide ultra low loading of the DUT. This, accompanied with superior signal fidelity, makes this probe useful for most of today’s digital logic voltages. And with its wide dynamic range (±8 V) and offset range (±12 V), the probe can be used in a wide variety of applications.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, Internal Termination, Failsafe, Remote Mount
40-781A-221-E
Relay
The 40-781A-221-E (PXI) and 42-781A-221-E (PXIe) are single failsafe SPDT 26.5 GHz microwave relay modules with internal terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
Infiniium EXR-Series Oscilloscope: 1 GHz, 8 Channels
EXR108A
Oscilloscope
1 GHz on all 8 channels, 8 instruments integrated in one, hardware accelerated plotting, and fully upgradeable to 2.5 GHz
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 18 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
42-788-121-TE
Multiplexer Module
The 40-788-121-TE (PXI) and 42-788-121-TE (PXIe) are single failsafe SP10T 18 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
20/26 GHz Coax, Receiver (50 Ohm, 26 GHz), Flex 402 Blue (50 Ohm, 34 GHz), SMA 3.5mm Plug
7-388102708-036
Coax Patchcord
20/26 GHz Coax, Receiver (50 Ohm, 26 GHz), Flex 402 Blue (50 Ohm, 34 GHz), SMA 3.5mm Plug
-
Product
Coaxial Transfer Switch, DC to 50 GHz
87222E
Coaxial Switch
Flexibility is essential in signal routing applications, and the Keysight 87222E 4-port coaxial transfer switch offers just that. It provides exceptional repeatability, low insertion loss, and high isolation. These switches provide simplification of design in signal routing and conditioning applications. The Keysight 87222E can be used in a variety of applications such as, a drop-out switch, switching two inputs and two outputs, or signal reversal switching.
-
Product
Ultrafast Photodetector with Current Monitor, 700 - 870 nm, DC - 25 GHz, FC/PC
DXM25CF
-
The DXM25CF Ultrafast Detector is a DC - 25 GHz, fiber-coupled, GaAs-based photodetector designed for applications in the 700 nm - 870 nm wavelength range. The core element of the detector is the fiber-coupled, hermetically sealed, microwave detector module. For convenience and simplicity of use, the module is mounted inside a rugged housing that includes a rechargeable battery, current monitor circuitry, and a digital display of the DC photocurrent.
-
Product
Signal / 20-26 GHz / 75 Ohm HD, Module, Receiver, TriPaddle, iCon Series, 64/8 Position
510160115
Receiver Module
iCon modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161115. (May mate with other ITA modules, as well.)
-
Product
25 GHz Differential Probe with 2.92mm Interface
DH25-2.92MM
Differential Probe
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Oscilloscope 50 GHz, 4 Channels
UXR0504B
Oscilloscope
UXR0504B Infiniium UXR-Series is the 50 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope.
-
Product
PXIe Microwave Multiplexer, Single SP6T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-785C-531-E
Multiplexer Module
The 40-785C-531-E (PXI) and 42-785C-531-E (PXIe) are single failsafe SP6T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
