Dry Blocks
-
product
Dry Bulb Temperature Probe for WBGT
TP3207
Pt100 sensor temperature probe. Probe stem Ø 14 mm, length 140 mm. Cable length 2 metres. Equipped with SICRAM module.
-
product
160-Pin DIN41612 Connector Block, Female
92-965-160-F
This connector block provides a simple method of connecting to high density DIN41612 connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
product
Standard Voltage 37 Pin D-Type Connector Blocks for Pickering
The connector blocks below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.
-
product
L Band Splitter, DC Block All Ports
PD5132
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
product
(70×90×12mm) Single Channel Gain Block MSA Compact Pre-Amplifier EDFA Module
SPA4300-GM02
Hangzhou Huatai Optic Tech. Co., Ltd.
SPA4300-GM02 is a gain block optical Pre-amplifier EDFA module, adopts 70×90×12mm MSA compact package. It is featured with high reliability, superior optical performance and compact reasonable configuration by Industrial standard, creating the most flexible and variable low-cost amplifier in the market. This module is suitable for multiple network application, especially the application that requires 40GB/S transmission speed.
-
product
Terminal Block For The 34934A Quad 4x32 Reed Matrix
34934T
This terminal block used for discrete wiring, supports up to 20 AWG wire size typical or 24 AWG if all 144 lines are used.
-
product
DUMMY BLOCK
STAG 10
Ideal requirements of release agent between billet and dummy block:Optimal adhesion to the substrate, Optimal anti-soldering power, No hazardous fumes/vapors development during use, Non-flammable at the effective temperature, No build-up, no interferences on run out table.
-
product
78-Pin D-Type Block Without Backshell
92-965-078-M
This connector block provides a simple method of connecting to 78-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
DC Blocking L-Band Splitter Combiner
PD5980
INSTOCK Wireless Components, Inc
PD5980 is an IP67 outdoor, weather resistant, DC blocking, eight way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5980 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 8 way power divider input rating tables for additional power handling info.
-
product
Gauge Blocks
Practical master gage for dimensional measurement Two types of steel and ceramic gauge blocks are available. Four classes of Class K‚ Class 0‚ Class1‚ and Class 2
-
product
L Band Splitter, DC Block All Ports
PD5162
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
product
Dry Mate Connector
Triton API 16D
API 16D: 3rd Edition Compliant Test PortsUtilizes Engineering-grade Plastics Instead of Traditional GRE MaterialUnique Keying and Color CombinationsPBOF Integration
-
product
Block Down-Converter
BDC Series 5” x 2.5” x 0.6”
*Connectorized Package *Compact, Rugged Design *Custom Designs Available *Internal Low-Noise LO *Automatic Switchover to Internal Reference ifExternal Reference is Removed
-
product
Hardness Test Blocks
Used to verify the hardness tester's performance and provide data in order to calibrate the hardness tester.
-
product
Gain Block Amplifiers
Qorvo designs and manufactures a wide selection of general-purpose, internally matched MMIC amplifiers that are targeted for many applications in network infrastructure and defense / aerospace. These components showcase the wide range of performance capabilities using Qorvo's processes. Our general-purpose gain blocks are internally matched and offer various gain and linearity levels in a variety of package types, giving customers many options for system design.
-
product
SCB-68A, Noise Rejecting, Shielded I/O Connector Block
782536-01
68-Pin Female Screw Terminal to 68-Pin Female D-SUB, DIN-Rail, Shielded I/O Connector Terminal Block - The SCB-68A provides a shielded I/O connection for interfacing I/O signals to plug-in data acquisition devices with 68-pin connectors. This Terminal Block combines with shield cables to provide low-noise signal termination. The SCB-68A incorporates a completely redesigned mechanical enclosure with a magnetic removable lid, DIN-rail mount compatibility, and a resettable fuse. It is compatible with single- and dual-connector Multifunction I/O with 68-pin connectors. The SCB-68A also includes two general-purpose breadboard areas and an onboard cold-junction compensation sensor.
-
product
Frequency Block Converter
FBC
The FBC-XX-FB is a full band system can be built upon a Keysight N8975A Noise Figure Analyzer (NFA) or X Series Signal Analyzer with option N9069A. This system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device covering Ka, U, V, E, W bands (26.5-170 GHz), when used with an Agilent E8247C signal generator (or equivalent).
-
product
DC Blocking Power Splitter Combiner
PD5060
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) 50 Ohm
-
product
Drying Time & Permeability
When developing a coating process, it is important to know the exact time it takes for the coating to dry or cure. For multicoat paint systems, having knowledge of the drying time enables the operator to know when any subsequent layers can be applied. There are many stages involved in the coating drying time. Once a coating has been applied, it levels off under gravity, and, as the coating begins to cure, a thin dry film appears on the surface. The coating then continues to dry until, finally, it is totally cured.
-
product
96-Pin Micro-D Connector Block, Female DIN Rail Mounted
40-966-096-F
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 6 or 10 Positions Blocks, UUT 456 x 320 mm
MG-07-01
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 456 x 320 mm (wxd)• Outer dimensions: 620 x 589 x 100 x 184 mm (wxdxh1xh2)• Equipped with dedicated cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
product
68-Pin SCSI Micro-D Conn Block DIN
40-966-068-M
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
High Voltage Dry Reed Relays For up to 10kV
Series 67 & 68
Series 67 PCB mounting with switch and coil connections in a Single-in-Line format.Series 68 PCB connections on the underside for coil connections. Flying leads from the top face for high voltage connections.The Series 67 and 68 are constructed using former-less coils. The absence of a coil supporting bobbin allows a device smaller than the industry norm. The unusual package design gives some interesting possibilities for high density packing.The option of flying leads for the high voltage connections makes it possible to keep this away from lower voltage circuitry on the pcb.Form A (energize to make) contacts are available with the option of 5, 12 and 24 volt operating coils.
-
product
Mini 4 Block Desktop Receiver
VGR4
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250VAC/5Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
product
Slot 0 Module Retainer Block Set, For Discrete Wiring, 1 Position
510109150
These module retainer blocks are used to attach modules directly to the inner frame of a VXI receiver for discrete wiring. These modules then hinge down with the receiver to provide easy access to wiring.
-
product
2 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 2 Ports
GPS212
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
product
DC Blocking Power Splitter Combiner
PD5080
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
product
DC Blocks
The Keysight DC blocks offer a new level of DC blocking with performance specified from 50 kHz all the way up to 67 GHz. Precision coaxial connector interfaces ensure an excellent impedance match across wide bandwidths, and come in a variety of RF connectors to fit your application needs. Two choices of DC Voltage ratings make these suitable for a wide range of applications.





























