Dividers
-
Product
64 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3069
-
DP-cPCI-3069 provides 32 Channel Digital Input / Interrupt and 32 Channel Digital Output with isolation. 32 Channel Inputs and 32 Channel Outputs are divided into groups of 16 channels each and are routed to rear I/O only.
-
Product
Bi-Directional Level Translator
IFB-10001
-
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
Product
Low Profile PCI Express 4-Port
7406e
-
The 7406e low profile PCI Express serial interface provides four RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
RF Power Splitter, Combiner, Divider
PD2578
-
INSTOCK Wireless Components, Inc
Wideband Frequency (2.4 - 6.0 GHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (22 dB avg)Excellent VSWR (1.20 : 1 avg)Outdoor Weatherproof ConstructionTri Alloy SMA Female (Jack) Low PIM
-
Product
Walk InDrive In Chamber
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Walk in/Drive in chambers can make test for large components, finished products like automobile.According to different test requirement and application, walk in chamber could divide into 2 types: Welded walk-in chamber and Modular walk-in chamber.
-
Product
NI-9381, 8 AI, 8 AO, 4 DIO, 0 V to 5 V, C Series Multifunction I/O Module
782580-01
Multifunction I/O
8 AI, 8 AO, 4 DIO, 0 V to 5 V, C Series Multifunction I/O Module - The NI‑9381 is a single, cost-effective module for general-purpose system I/O. The NI‑9381 combines common I/O circuitry into a single module to help system designers fit more functionality into a single system. The analog circuitry on the NI‑9381 is a multiplexed architecture that shares a single timing engine. The maximum sample rate per channel is divided by the number of both analog input and analog output channels in use. The NI‑9381 is supported in only CompactRIO Chassis.
-
Product
RF Power Splitter, Combiner, Divider RoHS, 8 Way, SMA Female, 350 - 1000 MHz, 50 Ohm
PD2480
-
INSTOCK Wireless Components, Inc
Wideband Frequency (350 - 1000 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy SMA Female (Jack) Low PIM
-
Product
UHF/RFID/TETRA Power Divider Combiners
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless 350-1000 MHz RF power divider combiners are optimized for UHF, RFID, and TETRA power splitting and combining applications. Wireless microphone systems also typically operate in UHF frequencies, making an INSTOCK device ideal for splitting or combining antennas in UHF wireless microphone systems. Available in 2-way thru 48-way configurations with Type N, SMA, TNC and BNC connector configurations INSTOCK.
-
Product
Power Dividers
-
Power dividers designed, manufactured and marketed by BroadWave are found in applications that include complex telecommunication lab configurations, test equipment, phase arrays and specific test modules.
-
Product
350 MHz DDS Signal Generator
425A
-
The 425A generates sine, LVDS and LVCMOS outputs simultaneously and is programmable in 10µHz steps from 250kHz to 350MHz and includes an LVCMOS Prescaler and Divider for generating LVCMOS frequencies down to 2 Hz. The 425A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution. The Frequency is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 5 VDC power. A Line Voltage AC Adapter is included. SOF8_425 windows software is also included.
-
Product
Rack Module with Standard Contactors with Anti-Harmonic Filters
MODF Rack
-
Lifasa - International Capacitors, SA
The MODF-RACK control units include, in a compact form, all the components necessary for the operation of a step of a capacitor bank with filters. MODF-RACK modules are divided into two basic blocks: power block and control block. The two blocks are mounted in a small frame to be installed in an electrical panel.
-
Product
Advanced Throughput Multiplier Feature, GTE 10.00p
K8215A
-
The Advanced Throughput Multiplier feature allows you to test up to two 1000 to 2000 node (between 1296 and 2592 nodes) boards simultaneously on a 4 module tester, thus dividing the test time by half.
-
Product
Quad IF Mixers / IQ Demodulators To 16 GHz
-
Quadrature IF Mixers incorporate a 90° hybrid, 2-way 0° divider and two mixers to produce two output signals in phase quadrature (I &Q) when driven by a LO and RF signal.
-
Product
90 Degree Hybrid Couplers To 600 MHz
-
This category of hybrid dividers features designs from 5 to 600 MHz with 2:1 to 4:1 bandwidth. Maximum insertion loss of 0.5 dB is specified for most units. These 90-degree hybrids are designed for a power rating of 1 watt maximum for a load VSWR of 1.2:1 or better. For use in 50-ohm environments.Pulsar Microwave currently offers this product line in three space-saving packages. The connectorized outline 412 comes standard with SMA female connectors. Outline C is a surface mount package useful for handheld applications with limited PCB area. Outline 301 is hermetically sealed for rugged environments.
-
Product
50% Beam Splitter
10725A
-
The 10725A 50% beam splitter, designed for beam diameters of 9 mm or less, divides the beam into equal parts. It transmits one part straight through, and bends the other part at a 90-degree angle. This optic is without housing and requires a user-supplied mount.
-
Product
192 Channel Isolated Digital Input / Interrupt Module
DP-cPCI-3780
-
DP-cPCI-3780 provides 192 channel digital input / interrupt with optical isolation. The 192 channel input is divided into 12 groups of 16 channels. The inputs are designed for a input voltage range from 5V to 28V.
-
Product
UHF/RFID Power Divider Combiner 2-Way, TNC Female, 350-1000 MHz, 30 Watts
PD2921
-
INSTOCK Wireless Components, Inc
PD2921 is a RoHS compliant, 2 way, wideband, 50 ohm, RF power divider, power combiner furnished with TNC jack female coaxial connectors. All wireless band frequencies in the range from 350 to 1000 MHz are covered with optimal RF performance. Max microwave input power levels up to 40 watts can be handled in both power splitter and power combiner applications. See 2 way power divider input rating tables for additional details.
-
Product
Embedded Components
-
Teledyne Labtech prides itself in being at the forefront of RF/Microwave PCB development. Teledyne Labtech were also one of the first companies to successfully develop techniques for embedding SMD resistors and capacitors within multilayer structures and the embedding of connector pins in buried stripline circuits.The advantages of such a structures ensures a much higher density of interconnect. This then removes the need for via-hole connections to the board surface or the need to create access pockets to the inner layers. Consequently you finish with a board with that exhibits much lower RF/Microwave losses. This is particularly important when designing large RF feed networks or 16:1 power dividers.
-
Product
RF Power Splitter, Combiner, Divider RoHS, 3 Way, Type-N Female, 698 - 2700 MHz, 50 Ohm
PD2030
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy Type N Female (Jack) Low PIM
-
Product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
-
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
Product
DC Blocking L-Band Splitter Combiner
PD5930
-
INSTOCK Wireless Components, Inc
PD5930 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5930 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
Product
High-Speed A/D 12-Bit Digitizers
Digitizer
GaGe 12-bit resolution digitizer models divide the input voltage range into 4,096 different digitization levels, which improves the delectability limit by a factor of 16 over the 256 levels of an 8-bit resolution digitizer model.
-
Product
IP67 DC Blocking L-Band Splitter
PD5141
-
INSTOCK Wireless Components, Inc
PD5141 is an IP67 outdoor, weather resistant, DC blocking, four way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5131 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 4 way power divider input rating tables for additional power handling info.
-
Product
Test Equipment
ST9001D5
-
Shenzhen Star Instrument Co., Ltd.
The ST9001D5 three-phase energy meter test equipment is full-featured and stable. Optional accuracy classes are 0.05, 0.02 and 0.01. The product series include: universal type, smart meter type, high-class reference meter type, and equipotential isolation type. As divided by structure there are combined type and integrated type. The meter test equipment is controlled via PC-based software. Choices of meter position are 3, 6, 8, 12, 24, 32 and 48.
-
Product
Light Sources
-
There are many low cost artificial light sources used for illumination or for industrial applications: tungsten or halogen bulbs, fluorescent lamps, LED lamps etc. Some of these sources have regulated intensity of emitted light. However, there very few calibrated light sources of precisely known parameters. A light source can be considered as calibrated when its user can precisely regulate its photometric/radiometric parameters like luminance (or illuminance), radiance (or irradiance) at defined spectrum of interest. Such light sources are needed in many applications among them, in systems for testing night vision devices, VIS-NIR cameras and SWIR imagers. Inframet offers a series of calibrated light sources that can be divides into three groups:
-
Product
6-Way Power Dividers From 0.4 To 22 GHz
-
Pulsar Microwave manufactures 6-way power dividers in connectorized packages spanning 400 MHz through 22 GHz. These narrow and broadband models are designed to operate in a 50-ohm system and are rated at 30 watts. The 6-way connectorized power dividers are available standard with wither SMA or N female connectors, though other configurations of BNC, TNC, F and male connectors are possible.
-
Product
ASC 3.0 Datacasting System
SkyScraper XM
-
SkyScraper® XM is a state-of-the-art data broadcasting system for distributing public and private digital content and NRT applications over ATSC 3.0 and hybrid networks. Using SkyScraper XM, TV stations, corporations, and other organizations can reach their targeted audiences, add revenue sources, and bridge digital divides.
-
Product
Hybrid Power Divider, 0.5 GHz to 26.5 GHz
87302C
-
The Keysight 87302C hybrid power divider is designed for power splitting applications that require minimal insertion loss and high isolation between ports. It has insertion loss between the main line and output port which is 1 to 2 dB less than equivalent resistive power splitters. It is designed for critical signal processing applications; phase and amplitude tracking between the two output ports is controlled and specified.
-
Product
Heat Cycling System
-
Yangzhou Power Electric Co., Ltd
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up.The system can perform the heat cycle testing for power cables type test and pre-qualification test according to IEC 60840, and IEC 62067 etc. Based on pre-qualification test needs, test system is divided into two parts: test sample loop and simulation temperature loop.
-
