OBD 2
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 2 Amp, 2m, 250 Port
A500RMR-F-5C200
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm
50-294-011
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
2 PRI + 24 BRI-U ISDN Simulator
CH-24BRI-U-MOD-2PRI
-
The most inexpensive ISDN simulator on the market. This unit has two PRI ports and 24 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
2 Ports 10GbE Advanced LAN Bypass Network Mezzanine Card
NMC-1010
-
Ideal for high-speed network connectivity and inline security monitoring. 1 x Intel® X710-BM2, 2 x fiber interface, 1 x PCIe 3.0 x8, Gen3, Advanced LAN bypass-bypass, normal, disconnect mode, RoHS compliant.
-
Product
Vertical Hinged Mounting Frame, G6, 5U, 2 Positions
310113397
-
This 2-position G6 Vertical Hinged Mounting Frame is for use with standard racks or PXI chassis. These mounting frames attach to flanges supplied by the chassis manufacturer and allow the receiver to hinge down for wiring access.
-
Product
Mixed Signal Oscilloscope - 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX4032A
-
350 MHz2 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
2 To 18 GHz 6 Channel Downconverter
-
Teledyne RF & Micrrowave's Six Channel 2 - 18 GHz (RF and LO) downconverter operates with an IF of ~960 MHz, providing 25 dB of RF-IF gain, and bandwidth of ~500 MHz. This downconverter operates on a single LO at -6 dBm which is amplified, split, then again amplified to each of the 6 channels. Integrated into each channel is a range extension switch, controlled by a TTL input and adding 20 dB attenuation. Noise figure is ~ 13.5 dB and output IP3 is ~+25 dBm. The downconverter is 2- sided, hermetically sealed and designed for rugged applications.
-
Product
150 A, 10 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 2 meter cable
CP150B
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Coaxial Termination, DC to 2 GHz
909C
-
The Keysight 909C is a precision, low-reflection dc to 2 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 909C may be ordered with an APC-7, type-N male, or type-N female connector.
-
Product
PXI 2 Amp MUX, Dual 16-Channel 2-Pole
40-635-006
-
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
QorIQ P40x0 Processor AMC, PCIe Gen 2
AMC718
-
The AMC718 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P4040 and P4080. The module follows the AMC.1 and AMC.2 specifications. The PCIe interface is configurable as Host or Agent mode and it interfaces as x8 or dual x4. The module has option for up to 16GBytes of DDR3 memory with ECC.
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 2m, 250 Port
A500RMR-05F050D5C200
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
PXI 8 Slot BRIC Solid State 64x8 1-Pole (2 sub-cards)
40-563A-121-64X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Vacuum-Pneumatic, Module, ITA, 90 Series, 1 Pos Vacuum, 2 Pos 3/8" ID Pneumatic
510108264
-
Primary mating module 510104276.
-
Product
Multiplexer 2:1 With De-Emphasis 32 Gb/s
M8062A
-
R&D and test engineers who need to characterize serial interfaces of up to 32.0 Gb/s can use the M8061A 2:1 Multiplexer with optional de-emphasis to extend the rate of J-BERT M8020A and J-BERT N4903B pattern generator. For the most accurate receiver characterization results, the M8061A provides four calibrated de-emphasis taps, which can be extended to eight taps, built-in superposition of level interference and Clock/2 jitter injection. The M8061A is a 2-slot AXIe module that can be controlled via USB from the user interface of J-BERT M8020A as well as N4903B.
-
Product
PXI 8 Slot BRIC 60x8 1-Pole (2 sub-cards)
40-561A-121-60X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PCIe 14 Bit High Speed Digitizer - 500 MS/s on 2 Channels
M4I.4450-X8
-
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
GPS, GLONASS, Galileo Micro Splitter 2 Way, SMA, 1176.45 - 1602.00 MHz, 50 Ohm, Passive
GPSL10
-
INSTOCK Wireless Components, Inc
GPSL10 is a two way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Max voltage rating is 50 VDC; maximum current rating is 1000 mA. Furnished with SMA female connectors all ports. Being a "micro-sized" splitter, GPSL10 weighs only 21 grams and is suitable for applications requiring low-weight parts.
-
Product
Cable Assembly, Receiver, Coaxial, 36", 6 SMA Plugs and 2 SMB Plugs
540265010207
-
Cable Assembly, Receiver, Coaxial, 36", 6 SMA Plugs and 2 SMB Plugs
-
Product
PXI Precision Resistor Module 4-Channel, 2 to 52.4k
40-297-133
-
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Mixed Signal Oscilloscope - 500 MHz, 2 Analog Plus 16 Digital Channels
MSOX4052A
-
500 MHz2 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
Insulation Resistance Tester for PV (2 range)
MIS-PV1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The model MIS-PV1 is an insulation resistance tester for the exclusive use in photovoltaic systems. The ordinary insulation resistance testers cannot make measurement properly during generation of PV systems. This instrument, however, can measure the insulation resistance simply by touching probe to the live line whether making generation or not. There are two ranges of PVH and PVL. PVH is for high voltage generation system (more than 500V and less than 1000V) and PVL is for the system less than 500V.
-
Product
PXI 2-Slot BRIC Matrix, 22x16 1-Pole (2 Sub-cards)
40-562B-221-22X16
-
The 40-562B-221-22X16 is a high density BRIC2 matrix module with a size of 22x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Precision Resistor Module, 9-Channel, 2 to 6.97k
40-297-030
-
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
SWB-2834, 8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781420-34
-
8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2834 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin Male VHDCI
540031020240
-
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin Male VHDCI.
-
Product
Automatic Trans. & Engine Oil Pressure Tester with 2 Gages
34550
-
Check oil pressure in automotive transmissions and engines.Adapters provide coverage of most domestic and imported cars and light trucks.Includes two gages: Large Gage calibrated from 1-600 PSI (0-4,000 kPa & 0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR)Large gage can be used for all applications and has hang-up hook. Small gage is for more accurate reading of engine oil pressure where maximum oil pressure does not exceed 50 PSI (3.5 BAR).Includes 6 feet of oil proof hose and 10 assorted fittings.
-
Product
PXI 4-Slot BRIC Matrix, 2A 1-Pole 150x4, 2 Sub-cards
40-568A-002
-
The 40-568A-002 is a PXI 1-pole 150x4 matrix in BRIC4 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-568A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
ATCA 5U 2 Slot Mesh w uTCA connector for SHMM
109ATCA502-9020R
-
The 5U 2-slot ATCA backplane is a switchless 2X Replicated Mesh with point-to-point links between the slots. However, a 1X Mesh can also be implemented on the 2-slot.
-
Product
2 Port 100GbE Single Host Network Mezzanine Card
NMC-6002FD
-
Single host NIC solution by using Mellanox ConnectX-5, Overlay networks support: VxLAN & NVGRE. CPU offload: TSO, LRO, GRO, Jumbo frame support (9.6KB) Compatible with FWA-6520, 5020, 6170, 6070 & 5070.
