Conductivity
-
Product
Corrosion Test Chamber
CME SF-CCT
-
CME SF-CCT chambers are designed to be flexible enough to comply with as many different CCT specifications as possible. These may be programmed to conduct a whole range of corrosion tests such as wet cycle, dry cycle, controlled humidity as well as the salt spray test in a single chamber. This can occur in any sequence and be repeated automatically. A wide range of optional accessories enable additional climates to be added to further extend the number of climates and conditions that can be created.
-
Product
Circuit Breaker Simulation Device
PSS01
-
PSS01 is the circuit breaker simulator,which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
Product
Handheld Digital Thickness Gauges
HC-210
-
Shenzhen Chuangxin Instruments Co., Ltd.
HC series of coating thickness gauge is a portable thickness gauge with eddy current thickness method and electromagnetic thickness method. It can be used to quickly and accurately measure the thickness of coating or cladding material without damaging it. As an essential instrument for professional material protection, this coating thickness gauge is widely used in manufacturing industry, metal processing industry, chemical industry and commodities inspection etc., both in the laboratory and in the engineering field. It can measure the thickness of nonmagnetic layer on magnetic metal substrate condition (such as steel, iron, alloy and hard magnetic steel, etc.) and the thickness of conductive layer on nonmagnetic metal substrate condition (such as rubber, paint, plastic, anodic oxidation film, etc.).
-
Product
Benchtop Conductivity Meter
LAQUA EC2000
-
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our compact and powerful benchtop model was developed to provide simplicity with excellent on-site usability.
-
Product
Specialist Inline Inspection
-
NDT Global treats each pipeline individually from the offset. Before a project even begins, a feasibility study of the pipeline detail is conducted by NDT Global, to determine the appropriate tool and required modifications to complete the inspection. NDT Global has an extensive engineering capability in this regard and has a proven track record in providing tailored solutions to deal with a wide variety of pipeline characteristics.
-
Product
PXI 3A Power MUX BRIC, 2-Channel, 48-Pole
40-571-002
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Bridge Decking Testing Equipment
-
The testing process can detect blow holes, inclusions or thin areas in 'sprayed-type' membranes. Because the concrete contains a small amount of water, it is electrically conductive and a DC Pinhole Detector can be used to create a high voltage which is passed over the surface by the use of a brush electrode. An alarm will sound to identify any small defects which can be rectified so that the integrity of the coating can be verified.
-
Product
2U Data Processing Computer
CP42102
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP42102 is a 2U ruggedized data processing computer compliant with PICMG CompactPCI® specifications. With ruggedized conduction cooling structure and CompactPCI® module design, CP42102 has excellent performance on heat dispassion and anti-vibration, and can save costs on maintenance in the long run.CP42102 can meet the demands for big data processing, computing and storage, as CP42102 is equipped with a 3rd Gen embedded Core™ i7 high-performance processor with up to 16GB memory and 1TB storage. On CP42102, interfaces like Ethernet, USB, serial ports, VGA, etc. are routed to the rear through aviation plugs; inside the chassis, CPU slot and 2 service slots are connected by 1x LVTTL; outside the chassis, 2 N50K RF interfaces are added for external interconnection.
-
Product
Hardy Shaker
HI-903
-
This is our top of the line Hardy Shaker. It provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting vibration tests easier. Tests can be conducted on multiple vibration transducers, and then the saved data can be transferred via USB Flash Drive to be displayed in an automated and customizable report using an Excel template on your computer. In manual mode, the vibration test level and test frequency can be set from 7 Hz to 10,000 Hz. The high accuracy instrument can display the vibration level in terms of g’s peak, velocity peak (in/sec or mm/s) or displacement peak-to-peak (mils or µm). The unit can support payloads up to 800 grams (see frequency limits in the manual). A built-in display reads the output sensitivity, which can be stored in memory. Complete testing sequences and data can be stored in memory for each tested sensor, the unit logs the data on the spot or stores it for later use. For testing of heavy transducers or at high frequencies, the HI-903 automatically corrects the sensitivity calculation for the effects of transducer mass loading. A built-in self-test program checks for accuracy of all calculations. The HI-903 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.
-
Product
Silicon Detectors
-
Through the photovoltaic effect, detectors provide a means of transforming light energy to an electrical current. The root of the theory behind this phenomenon is a small energy gap between the valence and conduction bands of the detector. When light, with enough energy to excite an electron from the valence to the conduction band, is incident upon the detector, the resulting accumulation of charge leads to a flow of current in an external circuit. Since light is not the only source of energy that can excite an electron, detectors will have some amount of current that is not representative of incident light. For example, fluctuations in thermal energy can easily be mistaken for light intensity changes. A variety of these "non-light" contributions are present and, when summed up, make up the total noise within the detector.
-
Product
3GHz EMC emissions Analyser
SA3000
-
The SA3000 is a powerful, fully featured, EMC analyser. It will measure both conducted and radiated emissions according to the international EMC standards. It enables the user to assess the EMC compliance of products quickly and with good integrity.
-
Product
Universal Transmitter
Model LXT-380
-
Teledyne Analytical Instruments
The Model LXT380 transmitter is a single or dual channel, intelligent, multi-parameter designed for the online continuous measurement of pH, ORP, Specific Ion (pION), dissolved oxygen, free chlorine, total chlorine, conductivity and resistivity. The Model LXT380 Tramsitter digitally communicates with the SP3X digital sensor, automatically configuring the trasmitter's menues and display screens to the measured parameter. The LXT380 tramsitter can be Loop powered or 4-wired DC powered. The standard configuration has a 4-20 mA and a serial communication port with MODBUS RTU output. Alarm relays option is only available on 4-wired DC powered transmitters. LXT380 Transmitter loop is available in FM, ATEX and IECEx certifications.
-
Product
Mobile metal analyzers
-
SPECTRO Analytical Instruments GmbH
Mobile metal analyzers have been used for over 30 years to conduct metal analysis onsite. The rapid development in instrument technology has led to significant advances in the application possibilities. As a technology leader, SPECTRO has markedly shaped and formed this development from the start. As the worldwide market leader in this area, SPECTRO is today the only company to offer a complete range of metal analyzer products from handheld XRF to arc spark OES spectrometers for the many different tasks in onsite metal analysis.
-
Product
Moisture Sensor Probe
28092
-
The Moisture Sensor Probe is a fork-like physical package that easily inserts into soil or other soft, non-corrosive media. This sensor uses conductivity to detect the amount of moisture between the probes. The likely use of this sensor is in potted plants, micro-farming research and with some non-soil environments.
-
Product
Limiter
-
Chengdu KeyLink Microwave Technology Co., Ltd.
The series of products‘ limiting ability can be achieved by the diode conduction and cut-off characteristics.The frequency range covered by 0.5GHz~40GHz.The products have the characteristics of low insertion loss, small size and high reliability. The products can be applied to receiving channel low noise amplifier protection in radar system. KeyLink's limiters can be categorized as follows.
-
Product
IC Measurement Technology
Emission
-
is used to measure conducted emissions (measurements with direct 1 Ohm/150 Ohm-coupling) according to IEC 61967-4 at IC pins.
-
Product
On-site Support
-
Aerodyn provide a complete field test service, offering on-site support at demanding and often remote test sites. We instrument test articles, route lead wires, configure data acquisition systems, record data, reduce data, and write test reports. We conduct tests on aircraft, in test cells, at power stations, aboard ships, and at manufacturing facilities.
-
Product
300 W VITA 62 PSU Conduction Cooled | 3 U | 5HP
065-862
-
300 W DC/DC PSU VITA 62 for conduction cooled applications with IPMI controller.
-
Product
Cyrogenic Solutions
-
Our leading edge dewar technology combines the highest quality, reliability and expertise in thermally conductive materials. Our unique designs allow you flexibility to use standard dewars for more than one specific application or test.Minimize cryogenic consumption and maximize thermal conductivity.Vibration isolation to enable the most vibration sensitive applicationsTime-tested ergonomic designs for ease of operation
-
Product
Handheld Water Quality Meters
LAQUA PC220
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater- With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
Product
Non-contact Inline Sheet Resistance Measurement Module For Conductive Layer On Substrate
NC-700
-
*Inline measurement module for moving substrates such as PET film, glass or paper*Continuous measurement(~24h) in Roll to Roll with OFF-SET FREE capability system*Various applications from the research and development to the production line
-
Product
Full Bridge Thin Beam Force Sensors
TBS SERIES
-
The TBS Series thin beam force sensors many different parameters found in medical instrumentation, home appliances, process control, robotics, and automotive are exceptionally suited for small load measurements. They are designed to measure and many other high volume applications. A specially developed integrated strain gage includes all balancing, compensating and conductive elements and is laminated to the beam to provide excellent stability and reliability.
-
Product
Surface Resistance Meter
-
Wolfgang Warmbier GmbH & Co. KG
Starterkit for testing conductive an dissipative surfaces and electrostatic fields/surface potentials
-
Product
Professional Floor Certification Kit
PFC-252
-
The PFC-252 includes Prostat's PRS-812 Resistance System Set with modified 5 pound conductive rubber electrodes and Prostat’s Cable Spacers for exact measurements. The PRS-812 wide range resistance system can take measurements at 10 and 100 volts with accuracy within ±5%. Also included is the PFK-100 Field Meter Set. The PFK-100 set includes Prostat's unique PFM-711A dual range field meter, CPM-720A charged plate monitor assembly and PCS-730 ±1 kv charging source. With this instrument set you can measure electrostatic fields, analyze ionizer performance and assess the voltage generation of materials, equipment and personnel.
-
Product
Oxygen / Nitrogen / Hydrogen Analyzer
ELEMENTRAC ONH‑p 2
-
The new ELEMENTRAC ONH-p 2 is a powerful and robust elemental analyzer for measurement of oxygen, nitrogen and hydrogen concentrations in inorganic materials like steel, iron, copper or ceramics. The highly sensitive NDIR and thermal conductivity detectors reliably detect element concentrations from low ppm content to high percentages.
-
Product
Handheld Gas Detection Meter
GT-Fire
-
Teledyne Gas & Flame Detection
The GT-Fire is a dedicated hand-held gas detection meter specialized for the fire industry.It provides the confidence and assurance required by fire fighters when called to safety-critical environments.The GT-Fire enables gas detection to be conducted via one instrument in a complete, professional and timely manner, with easy access to data simplifying the reporting process.
-
Product
Seismic Acquistion QC Serivices
-
Overall data quality / cost monitoring / safety / daily reporting to client. Verif-i provides technical and operational programme assurances for seismic surveys conducted for the company. The lead acquisition QC on-board/on-crew the seismic vessel/block accepts or rejects data on behalf of the company. Our representative will assist the contractor in fulfilling the technical and operational requirements of the seismic programme and report on crew activities.
-
Product
Avionics Radio and Pulse Tester
T-RX
-
Streamline your avionics radio testing process with the CCX Technologies T-RX Avionics Radio and Pulse Tester. The T-RX is an all-in-one avionics tester that conducts 100+ tests on over 16 systems with only 1 device!
-
Product
PXI 3A Power MUX BRIC, 15-Channel, 16-Pole
40-571-205
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Capacitive sensors
-
Capacitive sensors can detect metallic, non-metallic, transparent, opaque, liquid and solid, conductive and non-conductive substances reliably without the need for contact. They are thus well suited to detect a diverse objects or also bulk goods and liquids.




























