Dust
See Also: Sand, Dust Chambers
-
Product
Linear Actuators
Electrak Pro
-
Thomson introduces our Electrak Pro Series of linear actuators. This family stands alone when it comes to the toughest and most demanding applications. Available in 12 or 24 VDC models with customizable stroke lengths up to 300 mm (12 in), these units can push or pull loads up to 4448 N (1000 lbf) at speeds of 20 mm/s (0.8 in/s) and hold loads up to 9000 N (2000 lbf), or contact our factory for longer strokes or higher loads. When space is scarce, where dust, dirt, and water are abundant and when solid, reliable and maintenance-free operation is a must - Electrak Pro is the answer.
-
Product
FD-11637, 8-Channel Strain/Bridge Input Device for FieldDAQ
785641-01
Strain/Bridge Input Module
8-Channel Strain/Bridge Input Device for FieldDAQ - The FD-11637 can measure eight channels and has built-in bridge completion and voltage excitation to support for quarter-, half-, and full-bridge sensors. It also features anti-alias filtering, offset nulling, and shunt calibration to reduce the effect of noise and improve measurement accuracy. The FD-11637 has an ingress protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 grm vibration. The FD-11637 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11637 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11637 is ideal for test cell and outdoor environments.
-
Product
Maintenance & Maintenance-/Service Contract
-
With cars it is easy: Change of oil, check of breaks and V-belt .. etc. - that is normal. But your test system does not need all these things. However it makes sense to look after your test system occasionally and check or change special idems. If you take the time and plan a preventive maintenance your test system will have less unplanned failure times. Less dust means less heat and slower ageing of electronic components.
-
Product
Dial Indicators
-
1. Always select the dial test indicator that best fits the application.2. Care should be taken while using a dial test indicator, try not to jolt the indicator, should you be unfortunate and drop a dial test indicator, get it re-calibrated/repaired before reusing it.3. Replace worn contact points only with those of a similar length from the centre of the ball stylus to the abutment shoulder.4. Always clean dial test indicators after use with a lint free paper or cloth and store the indicator in its box or in a dust free area.5. When using a dial test indicator, always position the dial test indicator in a horizontal plane to the surface media.6. Always use a rigid stand for mounting the dial test indicator.7. When measuring a rotating object, either between centres or in a vee block, ensure that the object is rotating in the correct direction. Never rotate the workpiece towards the contact point.8. When measuring a sliding object, only take readings when the object is moving directly towards the contact point, never away from the contact point or in a sideways manner.9. Avoid parallax errors by reading the dial directly from the front and square on to the dial.10. Never oil a dial test indicator as this attracts contamination, should the movement become erratic then the dial test indicator should be submitted to a reputable repair agent.11. Try not to expose dial test indicators to direct sunlight or in a high humidity environment.12. Never use a dial test indicator that has not been calibrated, if in doubt consult an appropriate authority.
-
Product
3U Centrifugal Blower for Pressurizing Consoles
CB-300A
-
3U centrifugal 300 cfm blower for pressurizing consoles, computers and electronic systems with cool, filtered air. Includes easy-to-remove, washable dust filter, 3-conductor AC cord and removable, brushed aluminum grille. Installs on 19” panel mounting rails.
-
Product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SFF
Model 6350
-
- Now available in RFSoC Gen 3 with the Model 6353- Small form factor rugged enclosure- Conduction-cooled- Designed to the IP67 specification for dust and water immersion- Sealed military-grade circular connectors- Incorporates Xilinx® Zynq® UltraScale+" RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- Optional dual 100 GigE UDP optical interface- Optional fan cooling for benchtop use- Navigator® BSP for software development- Navigator® FDK for custom IP development- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
Wireless Fiber Inspection Probe
OCI-20BN-W
-
OCI-20BN-W is a portable optical fiber connector inspector for checking fiber and connector end-face cleanliness, ideal for bench top and fiber optic network installation technicians to eliminate error caused by poor quality or improper cleaning.OCI-20BN-W offers excellent viewing on connector/fiber end-face and is able to feature to record and save image/video of fiber end-face; It can be connected to PC or phone by WIFI.More than 40 assorted high-precision tips designed for inspection solutionsAngled/Lengthened tips for awkward positions.Connect smart phone for testing FiberEye2 is the application on an android or IOS smart phone to capture, display and record the fiber end-face image from the Wi-Fi probe.Connect tablet/laptop for testing EFD is the analysis software on Windows tablet/laptop to have dusts, and scratches on end face inspected, analyzed, compiled and reported
-
Product
Climate Test Chambers
-
Infinity Machine International Inc.
Climate Test Chambers by Infinity Machine International Inc. - for applications such as dust proof climate test chamber for lighting, dust climate chamber for lab, and more.
-
Product
Laser Distance Meter
KM 973
-
Kusam Electrical Industries Limited
• Measuring Range : 0.05 to 40M (KM 973) , 0.05 to 70M (KM 975), 0.05 to 100M (KM 976) • Measuring Accuracy : ± 2 mm• Display Accuracy : 1 mm• Laser Classification : Class 2M II• Laser Type : 620-690nm, <1mW• Protection against splashes and dust : IP 54• Temperature range for Operation : 0°C to +40°C• Temperature range for Storage : -20°C to +70°C• Laser Switch-OFF Automatically : After 30 Seconds• Instrument Switch-OFF Automatically : After 3 Minutes• Area, Volume Measuring.• Indirect (Pythagoras) Measurement.• Plus-Minus Method.• Continuous Measurement.• Minimum / Maximum Measurement.• Display illumination.• Show beep.• Battery Life : 5000 to 8000 Measurements• Battery Selection : Lr6 (AA) 2 x 1.5V• Dimensions : 121(L) x 56(W) x 28(H) mm• Weight : 150g
-
Product
Transportable Gas Analyzer
CFP-8000
-
The CFP-8000 is pretreatment unit that is used with CGT-7100 or NOA-7100. When performing continuous gas analysis, dust and moisture must be removed from the gas before sending to the analyzer. This essential preprocessing can be performed by this one device, and two lines of cleaned measurement gas can be used simultaneously. Light-weight and compact, the CFP-8000 is the perfect preprocessor for use with portable analyzers.
-
Product
Environmental Test Chamber
-
Shenzhen Bonad Instrument Co., Ltd.
Climatic Test Chambers are also referred to as environmental test chambers, which are the general name of various test equipment used to simulate the natural environments of raining, high temperature, low temperature, dewing, salt mist, illumination, dusting, etc. There are kinds of testers including constant temperature chamber, constant humidity chamber, ozone aging test chamber, UV accelerated weathering tester, vacuum hot air oven, salt spray chamber, steam aging tester, rain test chamber, dustproof test chamber, ventilation aging chamber, xenon lamp weathering test chamber and so on. BONAD provides various environmental test chambers. You are welcome to contact us. BONAD will provide you with professional technical consultation and high-quality testing equipment.
-
Product
Dust Chamber Manufacturer
-
Wewon Environmental Chambers Co, Ltd.
Wewon Environmental Chambers Co., Ltd. is a good dust chamber manufacturer and made a 3380 liters blowing sand and dust test chamber for a Vietnam customer last week. The controller system of this 3380 liters dust test chamber can be connected to the computer.
-
Product
Dust Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Dust chambers provide a solution to dust test standards. Settling dust chambers applied very widely for automotive and electronic industry.
-
Product
Laser Levels
-
Fast, accurate and portable, PLS laser levels save time and money versus traditional layout methods using a bubble vials, plumb bobs or complex measurements. Compare the benefits PLS laser tools: Beam quality will be bright, thin and crisp. Drop tested with water and dust Ingress Protection (IP). Designed for the professional contractor with self-leveling technology. Green Laser Levels, Rotary Lasers, Point Lasers and Line and Combo Lasers.
-
Product
Temperature Sensors
TT420-LT
-
Features • 2-wire, loop-powered 4-20 mA analog output • Attachment probe, sensor, and 2-wire 4-20 mA signal conditioner • Integral 1/2" flexible liquid-tight conduit fittings • TT420Z-LT 1/4” stainless steel probe with 1/8 NPT adapter • TT420S-LT 3/8-16 threaded stud probe • FM approved, Dust Ignition-proof • Class II and III, Div I (E, F, G); NEMA 4
-
Product
Settling Dust Chamber
-
Dust material is placed in a collector, or trough, at the bottom of the chamber, where air nozzles periodically agitate the material, causing a cloud in the chamber. After the agitation, the dust cloud is allowed to settle onto the test sample, which sits above the collector.
-
Product
CEGRIT Automatic Flyash Sampler
-
The CEGRIT isokinetic particulate sampler is a device that can extract particulate samples of fly-ash, gift and dust from any fossil-fueled duct or chimney stack.
-
Product
MINI Data Logger for Temperature and Humidity
MINI-TH(Medical type)
-
Large-screen display of temperature and humidity, with battery, memory , recording status show together· High precision, mass memory for long-term logging· Free of toxicity and halogen as FDA / HACCP / ISO22000 require· Resistant to water and dust, suitable for cold chain systems of fresh food, fruit, vegetables or wine
-
Product
SDIO- Low Power Radios
-
Its industrial temperature support, robust enterprise security and 802.11ac capabilities make it an ideal solution for applications like factory automation with demanding environmental conditions such as with extreme temperatures, dirt, dust, moisture, shock, and vibrations. Its low power consumption also makes it suitable for portable handheld devices.
-
Product
Quad Input Logging Thermometer
DT304
-
UEi Test & Measurement Instruments
This series of Digital Thermometers offers a unique combination of features including logging capabilities with 9,999 memory positions and a USB interface and software, one, two and four inputs offering relative and differential readings. The Apollo also offers a solution to storing probes and is manufactured to conform to the IP67 standard, meeting performance expectations of water submersion and high-pressure dust resistance
-
Product
Speed Sensors
Series 18
-
Features • Square-wave pulse frequency output • NPN or PNP output options • Single channel or bi-directional options • 5-24 VDC powered • Hall Effect or Magnetoresistive sensing options • Standard and wide temperature options • Rugged M18x1 stainless steel sensor housing (all models) • Four housing options • All sensors are epoxy filled and sealed against liquids and dusts • Works with Electro-Sensors magnetic pulser discs/wraps
-
Product
Voltage Testers
DUSPOL
-
BENNING Elektrotechnik und Elektronik GmbH
phase-sequence test (counter-clockwise / clockwise)single-pole phase test: " symbol (red LED)measuring point illuminationacoustic and optical continuity testfrequency measurement 1 1000 Hzvoltage indication 1 1000 V AC TRUE RMS / 1200 V DCresistance measurement and diode test with conducting-state voltage indicationlc display with background lightingsensor of non-contact cable break detectorload connection via large-scale push buttonsvibrating alert in the test handleshock-resistant housing with protection against dust and water jets (protection class IP 65) and rubberized test handleDIN EN 61243-3 (VDE 0682-401): 2015 standard
-
Product
Sequence Control Valve
Code 200
-
Parker Conflow’s Code 200 is a sequence control valve which switches on electrical equipment by detecting the movement of a conveyor belt in dust suppression applications.
-
Product
Staple Lock Drum Sprays
2801
-
The Parker Conflow Code 2801 - staple lock drum spray provides a superior fluid spraying system for cutting drums in dust supression applications
-
Product
Handheld Digital Multimeter, 4 digit, Water and Dust Resistant
U1271A
Digital Multimeter
Feature sets that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.7% for ACV accuracy)Intelligent features to improve productivity and safety (selectable Low Pass Filter LPF and quick signal type identification Qik-V)Better grip Both visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 200) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
Product
Sand Dust Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
Multi-Scenario Simulation: Replicates desert storms, industrial dust ingress, and abrasive wear with programmable wind/sand profiles. Precision Particle Control: Cyclonic dispersion system ensures uniform particle distribution (ISO 12103-2025 certified). Durability: Hard-coated aluminum interior, wear-resistant seals, and self-cleaning filter traps. Smart Monitoring: Real-time particle counter, temperature/humidity logging, and AI-driven failure prediction. Energy Efficiency: Recirculating airflow design reduces energy use by 35% (ENERGY STAR® 2025 compliant).
-
Product
IP67 Testing
-
IP67 is an electronics and sealed device attribute requirement with a physical no-water ingress testing process used to determine whether components meet the requirements needed to receive an IP (ingress protection) rating. Devices with this internationally recognized rating resist exposure to dust and withstand up to 30 minutes of submersion in water up to 40 inches (1 meter) in depth. Products assigned an IP67 rating are typically used in outdoor applications or other environments requiring resistance to dust, moisture, and water submersion.
-
Product
19” Fanless IPC
-
The 19” fanless IPC is built to be used in industrial and military applications which call for this kind of robust and reliable systems. The solid steel housing meets industrial and MIL-STD-810 environmental requirements. Thanks to the fan less concept this systems are completely silent and there is no dust ingress into the system and no air dust filter needs to be serviced.
-
Product
pH 610 Waterproof Meter with pH probe
-
These waterproof handheld meters feature a –2.00 to 20.00 pH range with 0.001 pH resolution. Combined with accuracies up to ±0.002 pH, these meters provide a new benchmark in our pH meter line. Store up to 500 data sets in the meter‘s memory. Time-and-date stamping meets Good Laboratory Practice (GLP) standards.The pH 610 meters offer the latest in pH calibration capabilities including up to six calibration points, a user-settable “calibration due” alarm, and up to 15 buffer options with auto-buffer recognition of USA, NIST, DIN, and PWB standards. The infrared (IrDA) wireless technology makes PC downloading more convenient and easier. Dual powerup allows you to use batteries while out in the field or the optional AC power adapter while in the lab.As always, our waterproof meters are IP67 rated for protection against both dust and water, even with no probes attached.
-
Product
High Frequency Infrared Carbon and Sulfur Analyzer
CS-8820
-
Wuxi Jinyibo Instrument Technology Co., Ltd.
1. Infrared detector with low noise, high sensitivity and high stability. 2. The modular design of the whole machine improves the reliability of the instrument. 3. The electronic balance is automatically connected. 4, WINDOWS full Chinese operation interface, easy to operate, easy to master. 5. Dynamic display of various data and carbon in the analysis process. 6, measuring linear range is wide, and can be expanded. 7, high-frequency circuit design is reasonable, high-frequency furnace power is adjustable, suitable for different material sample analysis requirements. 8. The automatic cleaning device of the burner can reduce the influence of dust on the analysis results. 9. The burner heating device makes the conversion rate of sulfur tend to be consistent, which improves the stability of sulfur determination. 10, measuring linear range is wide, and can be expanded. 11. The software is fully functional, providing more than forty functions such as file help, system monitoring, channel selection, mathematical statistics, result correction, breakpoint correction, and system diagnosis.
