Bridge Amplifiers
Increase a transducers signal to measurable levels.
-
Product
General Purpose Amplifier
-
Easy to use 1.5V to 5.5V amplifiers with 69uA/ch and 150uV offsets, perfect for battery based or power concerned systems.
-
Product
RGB Digital Fiberoptic Amplifier
CZ-V20 Series
-
SUPER HIGH POWER RGB sensor Industry's best color differentiation. High resolution amplifier for triple 16-bit calculation. New Luster Detection Sensor Head. Dual digital display & Direct access. New UV sensor head for fluorescent Detection. Three detection modes for every target [Super I / C' / C+I]
-
Product
Low Noise Amplifier
LNA
-
Teledyne Defence & Space (TDS) Low Noise Amplfiers (LNA) are designed to amplify very low power signals without degrading the signal-to-noise ratio.An amplifiers is designed to increase the power of both the signal and the noise however the Low Noise Amplifier is specifically designed to minimise the additional noise so important information should not be lost.
-
Product
Hybrid Amplifiers
LNA
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of hybrid amplifiers cover a frequency range of 10 kHz to 6 GHz. Each amplifier is designed to be unconditionally stable and have excellent cascadability. Our amplifiers are designed using thin film technology and are integrated components that include internal DC biasing circuitry, allowing them to maintain excellent electrical performance over the 55˚C to 100˚C range. Hermetically sealed and screened up to space level, these amplifiers are ideally suited for hi-reliability and mission critical applications.
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
-
Product
Shunt Isolation Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Especially to accurately measure large DC currents via shunt resistors, ie for making isolated detection of mV voltage on shunts. Variants with calibrated range selection. Working voltage up to 3600 V AC / DC.
-
Product
Waveguide Amplifiers
-
VDI offers waveguide amplifiers for various applications. Waveguide amplifiers are able to boost a small input RF signal to a large output RF signal. For sample data on waveguide amplifiers, please refer to the Waveguide Amplifier Product Manual (also located under Resources). Please contact VDI for more information.
-
Product
InfiniiMax III+ Series Probe Amplifier, 4 GHz
N2830A
Amplifier
The N2830A Series InfiniiMax III+ probing system is the next generation of InfiniiMax probing, greatly expanding the measurement capability and usability of a probe capable of measuring all components of a differential signal. The built-in InfiniiMode technology allows customers to switch differential, single-ended, and common mode without adjusting probe tip connections.
-
Product
mm-wave Bridges for EPR/NMR Spectrometers
-
ELVA-1 produces mm-wave bridges and components for EPR spectrometers. Lots of scientific laboratories in the world use ELVA-1’s products in their EPR experiments. Up to 170 GHz operating frequency
-
Product
Logarithmic Amplifiers
-
Pasternack Logarithmic amplifier category includes a wide range of log amp components. Log amplifier products in this logarithmic amp category are built to precise RF and microwave industry specifications. Logarithmic amplifiers, like the other over 40,000 RF, microwave and millimeter wave components at Pasternack are in-stock. Not only are these logarithmic amp components in stock, they also ship the same day.
-
Product
In-Line Charge Amplifiers
-
The in-line charge amplifier is used to excite structures or machinery with a definable impulse force. Resonances are identified by impulse, an important measurement parameter for the study of dynamic behavior. The 4705A1 is a fast turn on time, 50 mV/pc, in line charge amplifier with BNC jack connectors on each side.
-
Product
High Voltage Op Amplifiers ≥12V
-
High supply voltage op amps are used in systems that demand the widest dynamic range with the best signal-to-noise ratio. Engineers turn to Analog Devices for high voltage amplifiers that deliver industry-leading performance. Increasingly, new high voltage amplifiers also offer features to improve system performance, cost, and robustness while easing the complexity of system design. New features include integrated input overvoltage protection (OVP), on-chip electromagnetic interference (EMI) filtering, higher electrostatic discharge (ESD) immunity, and greater resistance to latch-up in both powered and unpowered operations.
-
Product
Wireless Bridge Device
BR-300AN
-
BR-300AN is a wireless bridge device which can easily convert a 10/100/1000BASE-T wired LAN device to a wireless LAN device. It supports a wireless LAN communication in the 2.4GHz and 5GHz bands and enables a wired LAN device to join in a wireless LAN environment easily. It also supports enterprise security which allows you to use the Wireless Bridge BR-300AN reliably even in environments such as offices and healthcare sites which require security. This product is not available in North America.
-
Product
Difference Amplifiers
-
A difference amplifier is a special purpose amplifier designed to measure differential signals, otherwise known as a subtractor. A key feature of a difference amplifier is its ability to remove unwanted common mode signals, known as common mode rejection (CMR). Unlike most types of amplifiers, difference amplifiers are typically able to measure voltages beyond the supply rails, and are used in applications where large dc or ac common-mode voltages are present. They are ideal for current and voltage monitoring. Analog Devices offers a range of difference amplifiers, optimized for low distortion, low power, or high voltage performance.
-
Product
10 MHz AGC Distribution Amplifier
FS710
-
Stanford Research Systems, Inc.
For installations which require many 10 MHz outputs at a remote location from the source, the FS710 AGC Distribution Amplifier offers seven independent outputs from one input. With an AGC circuit capable of adding up to 30 dB of gain, this amplifier can be used to provide a 10 MHz reference at locations as far as a mile from the source.
-
Product
Amplifier Module
LNAM-B
-
Fully differential ultra-low-noise voltage amplifier module (LNAM) with selected bipolar rf transistors at the input stage. The amplifier exhibits ultra-low voltage noise, very high speed, and good dc precision. 50 Ohm input termination realized by negative feedback allows for the lowest possible noise temperature.
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
RF Amplifier
SA812C
-
Hangzhou Softel Optic Co., Ltd.
SA812C1/SA812C2 Field Bidirectional AGC Amplifier is a new high gain amplifier. Adopt optimized circuit design and scientific and rational process. High performance AGC control circuit inside is useful for stable gain and low distortion. It's the best choice for large and medium-sized bidirectional CATV transmission network.
-
Product
VME64 to USB 2.0/Optical Link Bridge
VX3718
-
The VX3718 is the new VME to USB 2.0/Optical Link Bridge that fully replaces the VX1718 (VME-USB) and V2718 (VME- CONET) models. The Bridge Implements a VME master controlled by a PC via USB 2.0 and Optical Link (CAEN CONET protocol) including all the functions of its two predecessors in a unique device.
-
Product
Instrumentation Amplifier
AAF-3G
-
Programmable, 2-Channel Instrumentation Amplifier for the AAF-3, AAF-3PCI, PGA-16 and OEM Data Acquisition Systems.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
Optoplex designed and produced high power single-mode and polarization-maintaining EDFA, which met MSA compatible requirements. C-band MSA EDFA Module with +23 dBm Output Power is Optoplex standard product. Optoplex designed Pre-EDFA provides more than 35dB gain with -40dBm input power. The Double-Cladding pumped EDFA produces 2W output power.
-
Product
8 Channel Fast Amplifier
V975
-
The Mod. V975 is an 8 channel fast rise time amplifier housed in a 1-unit VME module; each channel features a fixed voltage gain of 10. Channels are bipolar, non-inverting and can be cascaded in order to obtain larger gain values. Input bandwitdth is 250 MHz for signals up to 50 mVpp and decreases for larger ones (up to 110 MHz @ 400 mVpp). Each channel is provided with three LEMO 00 connectors, one for the input and two bridged for the output.
-
Product
Millimeter-Wave Amplifiers
-
When your application requires operating at Ka-band and above, trust Mercury Systems’ millimeter wave amplifiers to perform. With standard designs up to 65GHz and custom products available, Mercury is ready to support your high frequency requirement.
-
Product
Distribution Amplifiers
-
The Quartzlock range of distribution amplifiers are intended for use when multiple outputs from a single frequency standard/generator are required. This may be encountered in engineering labs, national standards labs, research and development, calibration labs and production. This is vital for the distribution of signals from other precision frequency standards like Hydrogen Masers, Cesium oscillators. For a technical discussion about distribution amplifiers go here or select a product range below.
-
Product
RGB Digital Fiber Optic Amplifier
CZ Series
-
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
Product
Amplifiers
-
Instead of cascading a set of narrowband amps, use a single amplifier from Keysight and enjoy ultrabroad bandwidths - like 0.01 to 26.5 GHz, 0.045 to 50 GHz, and ranges in between. But the best thing about Keysight broadband amplifiers is what they eliminate and reduce: noise, crossover networks, and multiple power supplies.
-
Product
Ultrafast Laser Oscillators and Amplifiers
-
Coherent ultrafast lasers are designed and manufactured to provide the best performance, portfolio and support in the industry.
-
Product
Repair of Six Diode Bridge Assemblies, P/N 5989C
-
CEHCO is specialist in repair of various rectifier assemblies. One such assembly is shown below:Specifications:- Six Diode Bridge Assembly, P/N 5989C- AC input terminals: (3, 4 , 5)- DC output terminals: (1), POSITIVE and (2), NEGATIVE
-
Product
LOCAL LOOP SIMULATOR FOR TR-114 INCLUDING BRIDGED TAP
458-LM-A1-30-TR114
-
The Model 458-LM-A1-30-TR114 Local Loop Simulator for TR-114 is the ideal solution for simulating test loops as defined in TR-114 and includes a Bridged Tap. In addition, it is also suitable for ADSL, ADSL2, ADSL2+, and VDSL2 chip/modem/DSLAM testing of straight loops out to 24,000
