Op Amps
IC used as voltage amplifier. Also known as: Operational Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 26-30 AWG
610138112
Primary mating contact 610138116. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14 AWG
610110147
Signal, Contact, ITA, TriPaddle, 10 Amp, 14 AWGThis contact primarily used in CASS applications.Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 50µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation Compliant
-
product
PXI Solid State Multiplexer, 10 Amp, Single 6-Channel
40-666A-012
The 40-666A-012 is a single 6-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Dual 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-002
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
500 AMP Carbon Pile Load Tester
710
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
product
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-104962000-036
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White, Single Ended ( 5 Amps).
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Square Post for Wire Wrap
610138118
Primary mating contact 610138200. (May mate with other Twin Female contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG, Single Ended ( 5 Amps)
7-104922000-036
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG, Single Ended ( 5 Amps).
-
product
Bipolar Power Supply, 0 to ±50 VDC, 100 AMPS, 10 KW, P/N 19215PS
Specifications:Bipolar Power Supply, 10 KW, P/N 19215PSInput: 220 / 230 / 240 VAC, 46 Amps, 1 PH, 50 HzOutput 1: 0 to ± 50 VDC, 100 Amps max, Upper SectionOutput 2: 0 to ± 50 VDC, 100 Amps max, Lower SectionEnclosure: 42″H x 32″W x 22″DAll connections are inside the enclosureThis unit is a dual output power supply
-
product
500-Pin SEARAY Cable Assembly, Male to Male, 1 Amp, 1m, 500 Port
A500RMR-500RMR-0A100
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 0.5m, 250 Port
A500RMR-C-4B050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
30 AMP Fuse Buddy Testers
FB305M
Can test circuit current up to 30 Amps - an easy way to check fuel pump amperage. Clever design allows for easy connection into fuse sockets. Fuse Buddy ends are molded into the shape of the fuse itself. During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. Fuse Buddy stays put & won't fall out of the socket, like test probes do.
-
product
Test & AMP Measure
IP Traffic
IP Traffic - Test & Measure is a software testing tool that can run on any PC with Windows 98, 2000 or XP. It can generate, receive, capture and replay IP traffic, and measure end-to-end performance and Quality Of Service over any IP fixed or mobile network.
-
product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 1m, 250 Port
A500RMR-500RMR-4B100
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 2 Amp, 0.5m, 250 Port
A500RMR-F-5C050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin D-type Connector, With Interlock
42-158-103-HI
The 40/42-158-103-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
Mini Power Contact, ITA, 65 Amp, 8 AWG
610115125
Primary mating contact 610116112. (May mate with other Receiver contacts, as well.)Mini Power contacts carry up to 65 amps continuous current, 480 VAC. Maximum resistance is 1 Milliohms.Operating Voltage & Current 65 Amps Max. Continuous – 8 AWG40 Amp Max. Continuous – 12 AWG30 Amp Max. Continuous – 14 AWG25 Amp Max. Continuous – 16 AWGContact Resistance 1 mOhms Max.Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 1000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 3.37
-
product
High Power, Contact, Receiver, 150 Amps, 2 AWG
610149101
Primary mating contact 610150101. (May mate with other ITA contacts, as well.)Specifications Operating Current 150 Amp Continuous using 2 AWG wireContact Resistance 0.35 mOhmsOperating Voltage 600VDC or Peak ACContact Body Cu AlloyInternal Contact Beams – Cu AlloyContact Plating Body - 10µ" Au over 100µ" NiInternal Contact Beams - 60µ" Ag over 50µ" NiOperating Temperature -40°C to +125°CT-Rise +40°C at 150 Amps+30°C at 125 AmpsContact Termination CrimpCycle Life 10,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 1.39
-
product
Power, Patchcord, ITA, 72", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps)
7-251414000-072
Power, Patchcord, ITA, 72", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps).
-
product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin SGMC Connector, With Interlock
42-158-003-HI
The 40/42-158-003-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White, Single Ended ( 5 Amps)
7-123926000-036
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White, Single Ended ( 5 Amps).
-
product
PCI 2 Amp Multiplexer, Dual 4-Channel, 4-Pole
50-635A-107
The 50-635A-107 is a dual 4-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
500-Pin SEARAY Cable Assembly, Male to Male, 1 Amp, 2m, 500 Port
A500RMR-500RMR-1B200
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.
-
product
Signal, Patchcord, Receiver, 36", TriPaddle, 24 AWG White, Single Ended (3 Amp)
7-104924000-036
Signal, Patchcord, Receiver, 36", TriPaddle, 24 AWG White, Single Ended (3 Amp).
-
product
Signal, Patchcord, ITA, 72", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-103922000-072
Signal, Patchcord, ITA, 72", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
-
product
PXI Very High Density Versatile 2-Pole, 2 Amp Multiplexer
40-613A-002
The 40-613A Very High Density Versatile 2-pole Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves.
-
product
Power, Patchcord, Receiver, 72", Micro Power, 12 AWG White, Single Ended ( 22 Amps)
7-252912000-072
Power, Patchcord, Receiver, 72", Micro Power, 12 AWG White, Single Ended ( 22 Amps).
-
product
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White XLPVC, Single-Ended (1.5 Amps)
7-121966000-036
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White XLPVC, Single-Ended (1.5 Amps).
-
product
Signal, Contact, ITA, TriPaddle, 7 Amp, .025" Square Post for Wire Wrap
610110145
Signal, Contact, ITA, TriPaddle, 7 Amp, .025" Square Post for Wire Wrap.Plated in 50µ" gold
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 2m, 250 Port
A500RMR-C-5C200
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
