Op Amps
IC used as voltage amplifier. Also known as: Operational Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14-18 AWG
610110129
Signal Contact (ITA)
Primary mating contact 610110128. (May mate with other Receiver contacts, as well.)
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 1 Amp, 1m, 500 Port
A500RMR-C-1B100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.
-
Product
Power, Patchcord, Receiver, 36", High Power, 2 AWG, to Ring Terminal (150 Amps)
7-221902688-036
Power Patchcord
Power, Patchcord, Receiver, 36", High Power, 2 AWG, to Ring Terminal (150 Amps).
-
Product
PXI 2 Amp Multiplexer, 1-Bank, 64-Channel, 1-Pole
40-657A-001-1/64/1
Multiplexer Module
The 40-657A-001-1/64/1 is a 1-bank, 64-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 2m, 250 Port
A500RMR-05F050D4B200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Square Post for Wire Wrap with Anti-Rotation
610138122
Signal Contact (ITA)
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
Single 8x2 1-Pole 16 Amp PXI Power Matrix
40-552-002
Matrix Switch Module
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
Product
Signal Patchcord, ITA, TriPaddle, 36", 14 AWG White Teflon, Single Ended, (10 Amps)
7-101914000-036
Signal Patchcord
Signal Patchcord, ITA, TriPaddle, 36", 14 AWG White Teflon, Single Ended, (10 Amps)
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 1 Amp, 2m, 500 Port
A500RMR-500RMR-1B200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.
-
Product
PXI/PXIe Power Relay Module, 25xSPST, 5 Amp, 50-pin SGMC Connector
40-153-003
Relay
The 40/42-153-003 is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
Single 24-Channel 1-Pole 5 Amp PXI Solid State Multiplexer
40-652-101
Multiplexer Module
The 40-652 range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. Each multiplexer provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300s on hot or cold switching. User connections are made via a 50-way D-Type connector which is fully support by our comprehensive range of cables and connector accessories.
-
Product
Signal, Patchcord, Receiver, 36", QuadraPaddle, 24 AWG White, Single Ended (5 Amps)
7-124924000-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", QuadraPaddle, 24 AWG White, Single Ended (5 Amps).
-
Product
PXI 2 Amp MUX, Single 8-Channel 4-Pole
40-635-103
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Power, Patchcord, Receiver, 72", Mini Power, 16 AWG White, Single Ended (19 Amps)
7-234916000-072
Power Patchcord
Power, Patchcord, Receiver, 72", Mini Power, 16 AWG White, Single Ended (19 Amps).
-
Product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14-18 AWG, Crimp/Solder
610110172
Signal Contact (ITA)
Primary use in CASS applications.
-
Product
80 AMP FUSE BUDDY TESTER
FB315
-
*Tests circuit current from 0 to 80A*Includes 20A maxi fuse for use with mini and ATC circuit testing*Resolution: .1A (100 mA)
-
Product
Microwave Wideband Externally Modulated Transmitters (without RF Amp)
MT80 (30KHz~40GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MT80 series microwave optical transmitter, adopts external modulation technique, are able to transmit 40GHz microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 40Gb/s high speed communication system. MT80 adopts low noise, narrow linewidth CW DFB laser as light source; LiNbO3 external modulator as signal modulation, no laser chirp, low dispersion distortion, high extinction ratio, Full-transparency operation mode. It can be applied in long distance and extra-long distance transmission after EDFA.
-
Product
PXI 2 Amp MUX, Quad 4-Channel 2-Pole
40-635-109
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 2 Amp MUX, Quad 16-Channel 1-Pole
40-635-008
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
High Amps, Contact, Receiver, 500+ Amps, 350 MCM
610152101
Power Contact (Receiver)
High Amps, Contact, Receiver, 500+ Amps, 350 MCMContact rated to 1500VDC for low duty test applications.Mating contact 610153102. (NOT compatible with other VPC contacts)Contact ONLY compatible with 310105172 Receiver.
-
Product
PXI/PXIe Power Relay Module, 36xSPST, 5 Amp, 50-pin SGMC Connectors, With Interlock
42-153-002-HI
Relay
The 40/42-153-002-HI is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 1m, 250 Port
A500RMR-500RMR-5C100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
PXI/PXIe Power Relay Module, 3xSP4T, 20 Amp
42-166-201
Relay
The 40/42-166-201 is a PXI/PXIe high density power relay module with 3xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
Product
PXI/PXIe Power Relay Module,5 Amp, 50-pin SGMC Connector
40-153-003-HI
Relay
The 40/42-153-003-HI is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
Product
Power, Patchcord, ITA, 72", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps)
7-251414000-072
Power Patchcord
Power, Patchcord, ITA, 72", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps).
-
Product
Open Pluggable Specification (OPS) Digital Signage Player With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q170 And Intel® AMT 11.0
OPS500-501
-
The OPS500-501 is a 4K resolution OPS compliant digital signage player supporting Intel® Active Management Technology (AMT) 11.0 for better remote management. The space-saving OPS signage module is powered by the 6th generation Intel® Core™ processor with Intel® Q170 chipset. It has one 260-pin DDR4-2133 SO-DIMM socket with up to 16GB memory capacity. Compliant with the Intel® OPS architecture, the 4K-ready signage player provides a high level of compatibility as well as simplified installation, maintenance and deployment for a lower total cost of ownership. The outstanding digital signage player, the OPS500-501, is connected to OPS-compliant display via a standardized JAE TX-25A plug connector that supports DisplayPort, HDMI 2.0, UART, audio, USB 3.0 and USB 2.0 signals. To meet various application needs, the powerful digital signage system offers rich I/O interfaces on its front panel, including one USB 2.0 ports, two USB 3.0 ports, one COM port, audio (in/out), HDMI and a Gigabit Ethernet port. This space-saving OPS signage player has one PCI Express Mini Card slot for WLAN connectivity and features one 2.5” SATA HDD for extensive storage needs.
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 1m, 250 Port
A500RMR-05F050D5C100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
200 Amp AC Current Adaptor
DL6701
-
The DL6701 is a compact 200A AC current clamp adaptor with voltage output via standard 4 mm connectors. To be connected to a digital multimeter or other voltage measurement device.
-
Product
PXI 12 x DPST Reed Relay 2.5 Amp
40-136-012
Relay
The 40-136-012 12xDPST reed relay module is part of our range of medium power, general purpose relay modules which are capable of switching voltages up to 200V and current up to 2.5A.
-
Product
PXI 16 Amp Power Multiplexer, Dual 4-Channel 1-Pole (SP4T)
40-662A-012
Multiplexer Module
The 40-662A-012 is a dual 4-channel, 1-pole (SP4T) MUX and is part of our range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer.
