Feeder
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-340SL
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-340L
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
Broadcast Components
-
Cable testing sections may be used to isolate the antenna inputs from the main feeder when testing either the antenna or feeder. These devices are normally installed between the main feeder cable and antenna inputconnector and allow access to the antenna input without the need to remove the main feeder cable. Cable test sections are particularly useful with large feeder cables that are difficult to manoeuvre.
-
Product
Two-Way Radio Communications and High Speed Data Transfer
Leaky Feeder System
-
Leaky Feeder systems offer clear two-way radio communication and high-speed data transfer capabilities throughout your underground complex.PBE’s Leaky Feeder System can be tailored to specific site requirements to provide the best radio coverage and data communications. This two-way radio system can provide complete communications coverage for your site, including above ground surface coverage. PBE offers design, supply, testing and commissioning of temporary and permanent communication infrastructures for underground mines, tunnels, plants and buildings. PBE provides a wide range of leaky feeder system options: conventional leaky feeder system, CMTS system, permanent radiating cable network and hybrid networks.
-
Product
Automation Operations
-
Schweitzer Engineering Laboratories, Inc.
Substation automation uses substation and feeder operating functions and applications to optimize the management of capital assets and enhance operation and maintenance efficiencies with minimal human intervention.
-
-
Product
Split type AC Current Sensor
CTF-200A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
Product
Electrical Balance Of Plant
-
Schweitzer Engineering Laboratories, Inc.
Protecting a generation facility encompasses more than just protecting a generator. Protecting motors, feeders, and station-service equipment is also critical to maintaining plant uptime. By combining SEL solutions, you can do all of that using reliable, field-proven hardware that is suited for use in utility-, industrial-, and commercial-scale power systems.
-
Product
Cable Identification System & Cable Phasing System
Impulse Phaser
-
With the introduction of direct buried, solid dielectric primary voltage cables, the IMPULSE PHASER has come into greater prominence for safely and accurately identifying buried primary cables, including jacketed neutral designs. The IMPULSE PHASER has been accurately used on paper insulated, lead covered feeders in excess of 20 miles and even on submarine cable 300 feet underwater.
-
Product
Automatic Tablet Weighing System
CIW 7.2/7.3
-
With the automatic weighing system CIW 7.2 / 7.3 LAB you weigh tablets, dragees, capsules and similar products. Based on the UTS tablet testing systems by Kraemer Elektronik, the standard unit offers a tablet separation system and a special transport star for precise positioning of the test specimen on the integrated scale.The CIW 7.2 / 7.3 LAB in the laboratory version is now equipped with the database-driven, intuitive all-in-one touch software and no longer requires additional software solutions for most areas of application.The functionality of the software can be extended modularly – matching your needs and requirements.Alternatively, you can expand the CIW 7.2 / 7.3 LAB weighing system with a 12-station feeder and/or a 12-station collector to perform multiple defined tests (12-station feeder) in one measuring cycle. All cleaning-related parts can be easily and quickly disassembled without tools.The CIW 7.3 LAB model is nearly identical to the CIW 7.2 LAB, but additionally features a precise measuring device for thickness determination.
-
Product
Interface Unit
CMM Automation
-
The Aberlink automation interface adds the capability for Aberlink 3D programs to be remotely controlled and monitored using an external system allowing any Aberlink CMM to be integrated with an automated component handling system, whether this be a fully controlled, PLC driven manufacturing system, a robotic loader or just an automatic bar feeder. The package comprises of an optically isolated digital I/O system and a software module that enables the software to be setup to follow a defined operating sequence to allow the automated operation.
-
Product
Through Hole Type AC Current Sensor
CTF-50B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of feeder cable.*Measuring range:AC 0.1A～50A.
-
Product
Conveyor Scale
KW-LU
-
This advanced belt conveyor-type constant feeder weighs various raw materials in particle or powder form, and products on the belt conveyor.
-
Product
Constant Feeder
KC-V
-
This constant feeder continuously supplies a fixed volume of raw materials.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-40
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～600A*Current measurements of feeder
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40P
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC 0.1A～500A*Current measurements of feeder
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-23S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 1A～200A*Current measurements of terminal feeder
-
Product
Bus Differential System
B90
-
The B90 Bus Differential System provides fast and secure low impedance bus protection for reconfigurable LV, HV, and EHV busbars. Use one B90 to protect up to 8 feeders and use three or more B90s together in a centralized phase segregated architecture to protect up to 24 feeders.
-
Product
Radio Vector Tester
-
Wuhan Sunma Technology Co., Ltd.
Radio & Vector Network Analyzer adopts the advanced digital and RF combination design technology, fundamental wave frequency mixing technology, digital IF processing technology, intelligent power management technology, etc. It comes with features of high precision, small size, light weight, battery power, can measure SWR, Return Loss, Cable Loss, Impedance, DTF, etc, is used to the field test of cable, feeder, and the reflection parameters test of RF components in science and teaching. SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40PS
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～500A*Current measurements of feeder
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-110S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
Post Wire and Die Bond Inspection Machine
IV-T3300
-
IV-T3300 is a post wire and die bond inspection machine with Dual JEDEC Tray Feeder System. It features a large inspection area of 600x500mm and a quick trays change of 5-7 seconds.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-33S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 1A～200A*Current measurements of feeder
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-40SQ
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of feeder*Low cost*AC 1mA～50A*High Sensitive and least affection from external magnetic field
-
Product
Flexible Pick & Place Machine W/ 64-feeder Capacity
MC400
-
The MC400 Pick and Place machine places an enormous range of components, quickly and accurately, from 0201s through 100 x 150 mm SMDs, including BGAs, MBGAs, CSPs, µBGAs, MLFs, flip chips, odd form components and ultra-fine-pitch parts down to 15 mil. The system is easy to program and operate and comes standard with universal CAD conversion and teach-in capability.
-
Product
High Speed High Mix Pick And Place
MC389
-
The MC389 sets new standards for SMT pick and place speed, precision, and flexibility. Based on the MC Series’ durable ball-screw and rotary-encoded drive train, its three heads and on-the-fly vision allow accurate placement of any SMD (including 01005 chips, µBGAs, and 12-mil pitch QFPs). With an enormous placement area of 650 mm x 460 mm (25.6" x 18.1") and a capacity for up to 160 Smart Tape and Stick Feeders, the MC389 can easily be configured for virtually any high-mix project.
-
Product
High Mix High Component Count Or LED Panels
MC388
-
The MC388 features four simultaneous heads with dual-vision alignment that can achieve placement rates of 10,500 CPH. When used as an inline machine, up to 192 Smart Feeder can be attached, providing a near-zero job changeover time. Plus, it has the huge placement area, high precision, and accuracy that users have come to expect from MC-series component placers. The MC388 is ideal for LED strips, drivers, or other large, high-component panels.
-
Product
RxAIT
-
*RxAIT includes a Receive Multi-coupler (RMC) with a series of duplexers and Low Loss Combiners (LLC)*Provides the ideal ground based antenna sharing solution and reduces feeder line count and tower loading*Provides a common receive distribution point for multiple base stations*Each cellular and PCS unit supplies 8 ports and supports 2 channels
-
Product
High Mix Pick And Place
MC392
-
The dual-head MC392 pick & place machine is ideal for high-mix, low- to mid-volume manufacturing environments. It holds up 160 Smart Ports for tape and stick feeders, plus has space for cut tape strips and waffle trays, allowing more parts to be kept resident on the machine for faster job changeovers. High-quality components and a sturdy build achieve placement accuracy of 30 µm, 3 Sigma at placement rates reaching 6,400 cph.
