BNC
-
product
Low Noise Differential Preamplifiers
Provide a high gain amplification to 1MHz with an AC output derived from a very low noise FET instrumentation amplifier. Each model has fixed gain settings of x1 (0dB), x10 (20dB), x100 (40dB) and x1000 (60dB) over a selectable bandwidths of 100Hz, 1kHz (HP), 3kHz, 30kHz, 100kHz and 1MHz (7000 model only). Noise referred to input is 7nV√Hz and common mode rejection is >100dB at 1kHz. Momentary pushbutton switches are provided that control coupling, bandwidth, gain and channel on/off selections. BNC connectors are provided for single-ended and differential input, ac output, and dc output (optional) connections.
-
product
NI-9223, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781398-01
±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9223 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9223: either four, 2‑position screw terminal connectors or four BNC connectors.
-
product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
8" Cable
CONW1553-1
Transitions from a card end connector (with IRIG) on the QVME-1553 or QVXI-1553X into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and four 8" cables with BNC cable jacks for I/O triggers and IRIG Rec/Gen.
-
product
Fanless Embedded System With Intel® Atom® Processor E3845 For Railway, Vehicle And Marine PC
tBOX100-838-FL
The tBOX100-838-FL is certified with E-Mark and ISO 7637 for vehicle applications. The rugged tBOX100-838-FL comes with the onboard low power quad-core Intel® Atom™ processor E3845 along with onboard DDR3L memory up to 4GB. The compact vehicle PC features five BNC connectors with four video-in and one audio-in as well as one capture card for DVR surveillance applications. The capture SDK is ready and integrated to support system integrators to speed up the solution development. In addition, it was designed to withstand a wide temperature range from -40°C to +60°C and vibration up to 3 Grms, equipped with intelligent power management at wide voltage range 9-36VDC. The tBOX100-838-FL is also compliant with EN 50155, EN 50121, DNV 2.4, and IEC 60945 for use in rolling stock and marine industries. The cost-effective embedded system adopts a heavy-duty aluminum extrusion and steel case to withstand the rigors of day-to-day operation. The compact size of the fanless transportation computer ensures that it can fit into a variety of space constricting environments. To ensure that the system can be integrated into various locations, the tBOX100-838-FL supports DIN-rail and wall mount. The feature-rich system is ideal for security surveillance, transportation controller, data transfer and management.
-
product
Terminations
Our RF termination loads (also know as terminators) are available in 1.85mm, 2.4mm, 2.92mm, 4.1/9.5, 4.3-10, 7/16 DIN, BMA, BNC, Type C, Mini SMP, MMCX, Type N, QMA, SMA, SMB, SMC, SMP, SSMC and TNC connector types. RF termination loads from Pasternack are organized into two categories, feed-thru terminations and RF terminations. Pasternack Enterprises RF load terminations include precision and standard versions and many are RoHS and REACH compliant. 0.25 Watts, 0.5 Watts, 1 Watts, 2 Watts, 5 Watts, 10 Watts, 25 Watts, 50 Watts and 100 Watts models. Pasternack RF terminations are offered with impedances of 50 Ohm, 75 Ohm or 93 Ohm. The frequency ratings for these RF coaxial load termination range from DC to 50 GHz. RF loads are available in female, jack, male, male to female and plug genders. Our RF termination loads varieties are RoHS and REACH compliant. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this RF terminator series is in-stock. Not just in stock, but also these RF terminations will ship the same day as they are purchased from Pasternack.
-
product
75 Ohm Mini SMB to BNC Adaptor Assembly
40-978-701-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
NI-9223, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783284-01
±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9223 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9223: either four, 2‑position screw terminal connectors or four BNC connectors.
-
product
Handheld Water Quality Meters
LAQUA WQ-310-K
- Single channel- Large colour graphic LCD screen (70 x 52 mm) with backlight - Built-in foldable meter stand- IP67 waterproof and dustproof- Battery and USB powered- Eco-friendly, shock-proof, scratch-resistant, and non-slip- Built-in sensor holders- Efficient sensor locking mechanism- Sensor's LED light as reading stability indicator- No sensor adapter needed for attaching multiple sensors together- Compatible with conventional electrodes having BNC and phono connectors and long cables- Sensor status indicator- Temperature sensor indicator- °C & °F temperature units- Sample ID setting- Detailed calibration data- Auto stable, Auto hold, and Real time measurement modes- Customizable meter kit - up to 5 meter-sensor kit combinations- Hands-free testing- Ergonomic design- Multi-language options- Versatile channel and adaptive display- Automatic sensor recognition function- Data transfer via USB or wireless communication- Printer communication- 3 years meter warranty
-
product
CABLE TESTER
MCT-7
Whirlwind Music Distributors, Inc.
This diagnostic cable tester has connectors for analyzing almost any type of cable combination. The convenient rotary switch allows testing of each conductor within the cable and can determine the internal wiring configuration. Tests NL4, 5 pin DIN, BNC, XLR, TRS, RCA and 3.5 mm types.
-
product
All-In-One Toner & Probe Kit
MT-7068
The MT-7068 All-in-one Toner & probe Kit lets you use Toner and Probe to validate and troubleshoot wiring on RJ11/RJ45 cables and connectors, USB, F, BNC, and RCA connectors, and it also supplied with alligator clips to work with. The MT-7068 Toner detects telephone and Ethernet service, indicates polarity and active line numbers on voice circuits, and indicates active pair number on Ethernet circuits. The MT-7068 Toner and Probe also provide standard functions such as visual and audible signal strength indication, analog toning/detection, and continuity testing. It is ideal for all maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling , etc.
-
product
BNC (M) To Multi-Stacking Banana Plugs
3957
BNC (m) to multi-stacking banana plugs. Converts BNC (Female) cables/connectors to top/side stackable banana plugs for test versatility. BNC connector and banana plugs are molded directly to the wire for pull strength durability anddust/moisture resistance.
-
product
LXI Dual 24x8 Video Matrix, MCX (75R)
60-711-004
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75 Ohm with the option of SMB or MCX connectors or, with a larger case size, BNC connectors. It is designed to provide a simple and scalable bidirectional matrix for video frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-711 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
product
FMC Module
SMT-FMC510L
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
product
8" Cables
RCONP1553-1
Transitions from each card end (non-IRIG) connector on various boards into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and two 8" cables with BNC cable jacks for I/O triggers.
-
product
Directional Couplers From 0.01 To 2000 MHz
Pulsar Microwave's low frequency directional couplers operate within the frequency range of 10 kHz to 2 GHz. They're available in either surface mount or connectorized designs. SMA female connectors are standard, but BNC, TNC, F, N, jack or plug are available upon request.Most of these directional couplers have a flatness of +/- 0.25 dB and directivity of 20 dB or better within the operating band. VSWR of 1.3:1 or better maintained on all ports for most models. Maximum power handling is between 1 and 3 watts depending on model.
-
product
MMW Field Sensors
ITS-9050
The Innovative Technical Systems ITS-9050 Detector is a sensitive, harmonic mixing detector designed to measure millimeter-wave free-space radiation. It is ideal for measuring radiation patterns of antennas inboth the near and far-field. The ITS-9050 employs a free-running dielectric resonator oscillator (DRO) and an integrated harmonic mixer with a waveguide RF input that either connects directly to a circuit under test or to an antenna for radiation detection. The resulting IF is amplified and detected by an IF log-detector that drives a front panel LCD voltmeter to provide an indication of signal strength. A DC output voltage from the log detector is available on a BNC connector to drive external data acquisition instrumentation. Also, a sample of the IF output is provided for measurement on a spectrum analyzer.
-
product
Accessory Kit, Type-N to BNC, 50 Ohms
11854A
The Keysight 11854A accessory kit furnishes the RF components required for measurement of devices with 50 ohm, BNC connectors and when using a network analyzer with a type-N configuration. The BNC accessory kit contains two type-N male to BNC female adapters, two type-N male to BNC male adapters, two type-N female to BNC female adapters, two type-N female to BNC male adapters, a BNC male short, and a storage case.
-
product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-0.5m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
2-Ch Sensor Amplifier
SR-2210
The SR-2210 sensor amplifier accepts constant-current line drive sensors and connects the signal to analyzers and recorders that would not otherwise be compatible with constant-current sensors.The units connects directly with BNC connectors to ONO's model MI-3111 microphone preamplifiers and NP-3000 series of accelerometers.With compact, light-weight, battery operation, it can save for preparation of measurement.
-
product
Capacitive Divider
It can be chosen as PD sensor for Techimp PDCheck, PDScope or PDBaseII systems. It is suitable for on line or off line PD tests onrotating machines, for both spot measurements and monitoring applications. A BNC termination is available to connect the coupler through a coaxial cable.
-
product
Gunn Oscillators
Gunn Oscillators are solid state microwave energy generators. These consists of waveguide cavity flanged on one end and micrometer driven plunger fitted on the other end. A gunn-doid is mounted inside the waveguide with BNC Connector for D.C. Bias.
-
product
Fast Timing Analysis
Zero-Time Box
The Zero-Time Box is designed to compare the start times of source units with the recording system. It is compatible with every source encoder that outputs a start signal on a BNC connector, and also supports every source controller and decoder that does the same. The Zero-Time Box can also be used as a 5 channel precision measurer of timing intervals.
-
product
Cable Assembly, Receiver, 20", Micro Power and Micro Coax, 4 BNC Plugs and 4 SMB Plugs
540297010147
Cable Assembly, Receiver, 20", Micro Power and Micro Coax, 4 BNC Plugs and 4 SMB Plugs
-
product
50 Ohm SMB to BNC Adaptor Assembly
40-978-501-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Cable Assembly, Receiver, TriPaddle, 48", 37-Pin Female D-Sub
540016010601
Cable Assembly PXI / VXI 6 BNC 48"
-
product
Direct BNC
0001045
Interface board plugs directly into National Instruments 68 pin multifunction and simultaneous sampling DAQ cards (PCI and PXI). First four analog inputs, two analog outputs, and trigger channels are available on BNC connectors (SMA/SMB optional).
-
product
Cable Assembly, Receiver, Mini Coax, 20", 4 BNC Plugs
540064010107
Cable Assembly, Receiver, Mini Coax, 20", 4 BNC Plugs
-
product
75 Ohm BNC to BNC Cable Assembly
40-977-701-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
O/E Converter
TIA-950
The TIA-950 optical receiver is the optimum instrument for the laboratory or for field use. This optical receiver can be used with a wide range of oscilloscopes and digitisers to provide the utility of a convenient, easy to use fibre optic probe. This compact unit mounts directly on the BNC input of an oscilloscope.





























