-
product
Standard RF Power Sensors
Coaxial Dynamics "Standard" line of RF Power Sensors provide DC currents proportional to the forward and reflected power flowing through the line. All models are designed to drive a 30A, 1400-Ohm meter, or provide approximately 100 millivolts across a 5K load.
-
product
Tidal Current Flow Meter
KDL’s tidal current flow meter gives you the ability to monitor the speed and direction of tidal currents . Tidal flow speed information is extremely important to aid shipping movements such as berthing.
-
product
Smart Home Flowmeter for Water
F3
Gentos Measurement & Control Co.
The F3 is a small compact clamp-on ultrasonic flow meter, based on the Time Comb Technology. The F3 is very easy to install: clamp it on to the pipe, connect it to power and set pipe diameter. The clamp-on design allows the installation in running systems without opening the pipe, providing minimum downtime and maximum availability.
-
product
Single Phase Multi-Tariff Energy Meter Type DDSF999
Bofa Instrument & Equipment Co., Ltd
Single phase multi-tariff energy meter type DDSF999 is used to measure 50HZ AC active energy and the power flow of peak, shoulder, flat and valley time. All of its functions comply with the relative technical requirements for class 1 single-phase watt-hour meter in IEC61036-2000, and its data communication rules obey the requirements of IEC1107
-
product
Stand-alone Ozone Delivery System For Advanced Processes
SEMOZON® AX8585
SEMOZON® AX8585 stand-alone ozone gas delivery system is designed around the AX8410 PRIME ozone generator to provide high flow, high concentration, ultra clean ozone generation and delivery. This fully configurable product line is designed to meet the ever changing needs of the semiconductor industry. Each SEMOZON AX8585 is a fully integrated, high output ozone gas delivery system intended for use in an increasing number of semiconductor process applications such as ALD, CVD, TEOS/Ozone CVD, photoresist strip, wafer cleaning, contaminant removal, and oxide growth.
-
product
Flow Measurement for liquids, gases and steam
Flow measurement for liquids, gases and steam. Consistent product quality, safety, process optimization and environmental protection – these are only a few reasons why industrial flow measurement is becoming more important all the time. Water, natural gas, steam, mineral oil, chemicals are some of the fluids that have to be measured day in, day out.
-
product
DP Flow Technology
DP Flow technology enhances your flow measurement capabilities by expanding on time tested and proven technology.
-
product
M-Class System
ACQUITY UPLC
The ACQUITY UPLC M-Class System delivers the performance you expect from nano- to microscale separations with the usability of an analytical-scale UPLC system. Each part of the system was designed and tested to deliver the right flow for the right column. The ACQUITY UPLC M-Class System provides excellent performance with overflow rates from 200 nL/min to 100 µL/min and a range of column inner diameter (I.D.) from 75 µm to 1.0 mm.
-
product
Anemometer-Thermometer
HD2103.1
Anemometer-Thermometer which use hot-wire or vane probes to measure air speed, flow rate, and temperature inside pipelines and vents (for temperature Pt100 sensor with SICRAM module).
-
product
Pressure Transducer Module
PTM-1000
Advanced Thermal Solutions, Inc.
The PTM-1000, Pressure Transducer Module, is a four-channel test instrument for measuring differential pressure in enclosures where air flow integrity is critical to proper performance. As the demand for more energy efficient cooling grows, the need for measuring the pressure at each source of heat generation will follow.
-
product
Quizix Precision Pumps
The variety of models within the Quizix line offers several key advantages. The wide range of flow rates, pressure configurations and available options allow Quizix pumps to meet virtually any experimental requirement from bench top to pilot scale.
-
product
Multimeter Clamps
The ideal tool for detecting and measuring the leakage currents flowing to earth.The versatile clamp also offers all the functions of a multimeter clamp.In addition, the clamp is equipped with an RMS converter to ensure that the measurements remain accurate even in the presence of distorted signals.
-
product
Gas Meter Synthetical Test Bench
SY8506
Hong Kong Songyang Industrial Ltd.
The test of the error of the rate of flow:Using the gas flow standard device (in the shape of the bell prover) as our standard equipment, we can figure the standard volume of the tested gas by using the high-precision revolving encoder to measure the descending displacement of the bell prover.
-
product
CH-06 PXIe 6-Slot Chassis
(Gen3, 500W)
The new CH-6 PXIe chassis allows you to create high-performance multifunctional systems for both collecting and processing large data flows, and systems for monitoring and adjusting electronic equipment.
-
product
5CH Gas Mixer
G-MIX 5CH
G-MIX is an integrated versatile system that can be easily employed to set up countless gaseous mixtures, the gaseous flows are accurately controlled by five MFC (Mass Flow Controller), every MFC has stored inside its memory the calibration tables for 10 different gases.
-
product
PXI-6239, 8 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module
779626-01
8 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6239 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, sinking digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6239 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6239 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
Sand And Dust Test Chambers
Dongguan Amade Instruments Technology Co., Ltd
Sand and dust test chamber is also referred as dust-proof chamber, which is able to simulate the sand storm by putting the test piece in the chamber to judge the damage of sand-and-dust weather to products. Equipment is mainly applicable to determination of sealing performance of product shells based on the IPX5 and IPX6 degrees. Testing machine features a flow of air carrying dust in a vertical circulation, resulting in cycle use of sand during the test. Sand and dust testing has great significance to master the specimen’s performance to defend the penetration of dust particles, to withstand the abrasion of sands.
-
product
8-CH Analog Input Module
ND-6017
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Network Analyzer Network Protocol and Forensics Tool
Unsniff
Unsniff Network Analyzer is a powerful analysis tool that allows you to work not just at the packet layer, but with PDUs and Flows too. It has comprehensive forensics and file carving abilities you can use to extract almost anything that can be found in network traffic. It is also scriptable so you can automate almost all tasks that require you to grapple with Packet Captures.
-
product
Polyalphaolefin Liquid Chillers
PAO
PAO, a fluid that does not react with water and is compatible with most metals, is the basis of the Bemco PAO-II series of fluid conditioners. Similar to the Bemco PCL Chillers, PAO-II Liquid Chillers are furnished as free standing caster mounted systems, ready to provide a reliable and precisely controlled flow of temperature conditioned PAO fluid. These systems are optimized for use with Polyalphaolefin fluid in an Aerospace environment.
-
product
Opacimeter on Trolley for the Measurement of Diesel Vehicles
MO T | VP 135044
Maschinenbau Haldenwang GmbH & Co. KG.
The MAHA Opacimeter on trolley is used for the measurement of diesel vehicles. The smoke opacity is tested and diagnosed in a time-saving and trouble-free manner in a partial flow procedure during free acceleration or under load of the engine. Rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA Opacimeter. Type-tested according to PTB requirements 18.09.
-
product
Dual-Pump Continuous Flow Systems
Teledyne LABS SyriXus continuous-flow systems couple two pump modules to a single controller, and use an active or passive valve manifold to provide non-stop, continuous feed of almost any fluid. The controller refills one pump while the other is delivering, using special algorithms to equalize pressure and flow of both pumps. This allows virtually pulseless transition at pump switchover while maintaining accurate flow rate.Two different valve packages are available to accommodate all types of fluids and specific requirements of your experiment or process.
-
product
Micro Dilution Tunnel
MDLT-ONE
The MDLT-ONE is designed to sample particulate emissions using the partial flow dilution method. A small portion of the total exhaust is diluted with HEPA* filtered air to create a constant flow rate through particulate filters to collect Particulate Matter (PM). Compliant to the latest regulations, the new MDLT-ONE is very compact and offers faster response by the use of high precision venturi flow meters and a piezo actuated valve.
-
product
Control System
CONTROLSTIK II™
The Myron L® CONTROLSTIK II™ Rinse Tank System dramatically reduces the amount of water used in continuous flow rinse tanks. At the same time, it automatically maintains optimum water purity, ensuring effective rinsing.
-
product
Carbon Dioxide Quality Control System
CDQC
Teledyne Analytical Instruments
Teledyne’s Carbon Dioxide Quality Control (CDQC) system offers an integrated package to continuously monitor impurities in carbon dioxide (CO2). The plug-and-play design allows for the user to select only the gases and features of interest to maximize cost benefit and space.Front door viewing windows allow for view of all analyzer displays, flow and pressure settings. Stainless steel tube fitting connections and NPT or metric electrical ports as required are conveniently located in a central location for ease of access. Sample conditioning, utility gas provisions and integral calibration gas solenoid valves are standard.
-
product
Field-installation Type Residual Chlorine Meter (Four-Wire Transmission, Water flow beads)
HR-200
HR-200 is connected to a residual chlorine sensor (RA-20), which allows the free residual chlorine concentration to be measured with high accuracy. It is sutable for waterworks, pool water sterilization, and desalination systems. The measurement method is a three-pole polarographic method, which enables continuous monitoring of residual chlorine concentrations without using reagents. Stable measurement over a long period was realized by physical polishing cleaning using beads.
-
product
Variable Area Flowmeters
Is a meter that measures fluid flow by allowing the cross sectional area of the device to vary in response to the flow, causing some measurable effect that indicates the rate.
-
product
Dielectric Loss Tangent Testing Instruments
Insulation materials in electrical equipment are used between a pair of electrodes; therefore it can be expressed as capacitors. Applying AC voltage to a capacitor with insulation materials causes an energy loss due to the leak current, the dielectric polarization, and the partial discharge. Because of this, the phase of the capacitor current is more delayed than that of a zero-loss current (reactive current) flowing in an ideal insulation material. The delay angle is called "Dielectric Loss Angle", and the tangent is "Dielectric Loss Tangent" (tanδ). Please refer to the technical guide explained in detail.
-
product
Network Emulator Software
NetDisturb
NetDisturb allows disturbing flows over IP networks helping to study the behavior of applications, devices or services in a “disturbed” network environment. NetDisturb is inserted between two Ethernet segments acting as a bridge and operates bi-directional packet transfer on Ethernet, Fast Ethernet and Gigabit network interface cards.
-
product
Gas and Vapor Delivery Systems
In thin film deposition, high-quality results start with how process gases are delivered, as they help create the stable environment needed for consistency by controlling flow, pressure and composition to support processes like ALD, CVD, and PVD. Advanced semiconductor devices developed for the most advanced computing processes, such as AI and edge computing, need the ultra-high-purity environments of our gas and vapor deposition delivery systems.
