Host
-
product
Xcelera Frame Grabber
Xtium-CLHS PX4
Building on the field proven capability of Teledyne DALSA’s Xcelera frame grabber series, the Xtium™-CLHS PX4 is based on AIA’s CameraLink HS standard and uses PCI Express™ Gen 2.0 expansion bus to deliver high speed image acquisition and image transfer to the host memory. Xtium-CLHS uses industry standard CX4 cable to delivery up to 2.1 GB/s of image acquisition over a single cable to go beyond 15m and host transfer speeds of up to 1.7GB/sec - all in a compact, half-length, single slot solution.
-
product
2 Port BRI-S/T ISDN Simulator PCI
BRI-2ST-PCI
The most inexpensive ISDN simulator on the market. Designed in standard PCI card form factor it has two S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network. Simulator card does not require any OS drivers, completely software independent and it take only power from the host computer.
-
product
MTM-USBStem: USB Microcontroller Module
CONTROL TEST ENVIRONMENTS through a wide-range of IO capabilities and enable communications between a host PC and any module on the BrainStem bus.
-
product
Flexible x1 PCI Express to MiniPCI Adapter
SKU-067-0X
Flexible x1 PCI Express to MiniPCI Bus Adapter (Adapter) was designed to convert PCI Express bus into standard MiniPCI bus. It allows connection of a standard 124-pin MiniPCI add-in board to a motherboard PCI Express connector.Adapter includes a MiniPCI Adapter board (downstream), x1 PCI Express host board and flat PCI Express cable.
-
product
12-Port PCI Express
PEX 8750
The ExpressLane™ PEX8750 is a 48-lane, 12-port, PCIe Gen3 switch device developed on 40nm technology. PEX8750 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
product
CPCI 48 Input I/O Card with Zilog Z8536 I/O Controller
CPCI-48IN
The input board consists of three Zilog Z8536 controllers for DC input control. An FPGA provides the timing and control. Each input has its own optical isolation, and supports a hardware adjustable resistor/opto-diode combination for various input voltage ranges. An AMCC PCI controller provides the interface to the host computer. All I/O is accessible from the front panel.
-
product
Packet Analysis Probe for PCI Express
N4220A/B
When purchased with a logic analyzer, the application software you order is installed on the instrument hard drive. If you need to add application support after your initial logic analyzer purchase or are controlling a logic analyzer from a host PC, you must install the appropriate software before you can make measurements.
-
product
Flexible MiniPCI Riser
SKU-068-0X
Flexible MiniPCI Riser (Riser) was designed to extend motherboard MiniPCI bus. The Riser includes a MiniPCI Host board, MiniPCI Adapter board and a PCI Express flat cable.
-
product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
Ignition Driver Units
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
product
QorIQ P5010/5020 Processor AMC, PCIe
AMC713
The AMC713 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the NXP P5010 (single core) or P5020 (dual core) processors. The unit provides dual x4 PCIe on Ports 4-7 and 8-11 per AMC.1 and the PCIe interface can be configured in Host or Agent mode.
-
product
Wireless Electronic Flight Bags
webFB
The ultra-compact webFB easily fits in the palm of the hand, yet incorporates the capabilities of both an AID and a wireless server. The built-in AID safely gathers essential data from the aircraft's ARINC 429 and 717 databuses and conveys it to custom software or EFB apps hosted on the internal server. Using a wireless connection to portable EFB tablets, the webFB securely delivers this valuable information right to the fingertips of the flight crew.
-
product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.825-04
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
USB Cable
787057-01
USB Cable - The USB Cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use this cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
product
PANAVIA Modules
AIM’s PANAVIA test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core design with one processor for real time bus protocol support, massive memory and IRIG-B time code encoder/decoder functions are standard. AIM delivers versions of our modules with extended temperature range and conformal coating. With 8 Tx and 8 Rx channels per module, functions include autonomous transmit sequencing, continuous clock and data transmissions, host controlled double buffering, programmable interrupts, data selection on specific tag identifier, selectable triggers on data and/or tags with full protocol error injection/detection, real time bus recording and time stamping to ensure your bus integrity. Each module is delivered with a Board Support Package (BSP) comaptible to the legacy PCI and cPCI hardware modules.
-
product
Sensor Interfaces
Sensor interface ICs enable a system to read out information from the input signal generated by complex sensors, providing a suitable output signal that is easy for a host system to display or process. ams sensor interfaces offer high accuracy, precision and sensitivity even when operating in harsh environments.
-
product
2-Channel 40KSPS Datalogging Oscilloscope / 2-Channel 5.5 Digit DMM CF Card
CFD200
The CFD200 is a new concept in test equipment that allows a PDA, laptop or tablet PC to be turned into a dual channel Digital MultiMeter with sophisticated analysis capabilities. SmartAnalysis software facilitates step-by-step fault investigation with instant display of results and an interactive diagnostic guide. With the CFD200 it is possible to integrate multiple measurement functions into a single hardware/software platform, providing high-level analysis features and a small, lightweight and portable unit. The CFD200 is an extended Compact Flash design offering two channels with full galvanic isolation to host and channel-to-channel. Each offers a scope function up to 40KSPS with full datalogging capability and 650V max. input voltage.
-
product
OPC Server
An OPC sever (OLE for Process Control) provides IO and more devices to communicate with a wide range of HMI/SCADA software packages residing on a host. Advantech''s OPC server for ADAM and modbus devices features OPC DA (data access) and AE(alarm and events) client for the rapid testing.
-
product
ADC & DAC PCIe Card Powered by RFSoC
iW-RainboW-G42P®
AMD Xilinx’s ZU49/39/29DR Zynq Ultrascale+ RFSoCRAM Bandwidth8GB, 64bit DDR4-2400 RAM with ECC for PS8GB, 64bit DDR4-2666 RAM for PL (Expandable)16 DAC channels through SMA connector upto 10Gsps16 ADC channels through SMA connector upto 2.5Gsps3/4 Length PCIe Gen3 x8 Host InterfaceIntegrated ultra low-noise programmable RF PLIntegrated SyncE & PTP Network SynchronizationNVMe PCIe Gen2 x2/x4 M.2 ConnectorFMC+ HSPC Connector
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 250 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.822-02
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
Power Load Switches
Low-resistance power load switches offer reliable overcurrent and thermal protection. They are designed for general-purpose power protection or for applications such as USB, hot-swap and power distribution. The power switches come in 1- or 2-channel versions with fixed and adjustable overcurrent limit. Some include a USB charge controller specifically designed to optimize USB host applications.
-
product
8 channel 16 bit Digital to Analog Module
CPCI-DA8-2
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system.
-
product
Universal Flash Storage
UFS
Universal Flash Storage (UFS) is a JEDEC standard for high performance mobile storage devices suitable for next generation data storage. The UFS is also adopted by MIPI as a data transfer standard designed for mobile systems. Most UFS applications require large storage capacity for data and boot code. Applications include mobile phones, tablets, DSC, PMP, MP3, and other applications requiring mass storage, boot storage, XiP or external cards. The UFS standard is a simple, but high-performance, serial interface that efficiently moves data between a host processor and mass storage devices. USF transfers follow the SCSI model, but with a subset of SCSI commands.The Arasan UFS IP family consists of Host controller IP, Device controller IP, and MPHY.
-
product
AdvintDAQ™ Data Acquistion
MAKO
The Mako platform is based upon use of NI CompactDAQ (cDAQ) product line consisting of a chassis, NI C Series I/O modules, and a Windows host computer connected over USB, Ethernet, or Wi-Fi. Mako systems provide an easy, flexible, expandable platform to meet the needs of any electrical or sensor measurement system. They control the timing, synchronization, and data transfer between a host computer and up to eight (8) C Series I/O modules. A single Mako can manage multiple timing engines to run up to seven separate hardware-timed I/O tasks at different sample rates in the same system. Multiple units can also be daisy changed together for larger applications.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Taiwan 110VAC
781630-11
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
PXI-8516, 2-Port PXI LIN Interface Module
781366-01
2-Port PXI LIN Interface Module—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver.The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
product
8 Channel ADC for CompactPCI
CPCI393
The CPCI393 8-Channel Differential Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
product
USB Cable
780534-01
USB Cable - The USB Cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use this cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
product
2MP Stereo Camera for NVIDIA® Jetson Nano™/AGX Xavier™/TX2
STEEReoCAM™
Houses two OmniVision's 1/2.9" OV2311 Monochrome image sensorHigh-speed 2-lane MIPI CSI-2 interface to connect with the Host ProcessorPlugs in to NVIDIA® Jetson Nano™/AGX Xavier™/TX2 developer kit2MP Global Shutter Sensor10-bit Monochrome output formatHouses 6-axis Inertial Measurement Unit (IMU)Baseline distance of 100mmAccurate depth sensing with a flexible range between 0.95m to 8mS-mount lens holder (M12) with pre-calibrated S-mount lens pairSupport Multiple SteereoCam to a Single board
-
product
SpaceWire PCIe
127
The SpaceWire PCI Express (PCIe) board is the latest addition to STAR-Dundee’s SpaceWire interface device family. It provides three SpaceWire interfaces with the optimised host software supporting high bandwidth transmission of SpaceWire packets directly to and from the host PC. The three SpaceWire interfaces of the SpaceWire PCIe are each fully compliant to the SpaceWire standard and operate at up to 300 Mbits/s. Not only an interface device, the SpaceWire PCIe also contains powerful routing capabilities and an RMAP Target. The device can also be used as a router. The router facilitates packets from one SpaceWire port to be routed to another SpaceWire port or into the host PC via the PCIe interface. There are three independent channels from the SpaceWire router to the PCIe interface, so traffic flowing over one port cannot block traffic for another port. In addition there is a separate control channel, so that the host PC is always able to access the control, configuration and status space of the PCIe regardless of the data flow.
