Battery Discharge
See Also: Battery Chargers, Battery Capacity
-
Product
Battery charger and analyser for Military Batteries
TS1340+
-
Driven by recommendations from the British MOD, and designed for military service the TS1340+ is designed to handle the most harshest of conditions. This unit boasts a much large range of features, and its greatly enhanced display and keypad layout makes error free battery maintenance a certainty.
-
Product
Battery Tester
G5.BT
-
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
Product
Corona Discharge Checker
MK-720
-
MK-720 enables finding of insulation deterioration on insulators, disconnectors, and circuit breakers, at hot-line condition!
-
-
Product
Cable Discharge Solutions
-
Cable Discharge Event, or CDE, is an electrostatic discharge event that occurs when a cable is connecting to a piece of equipment with different potential. It occurs because there is a potential differential between the charge on a cable to be connected and the equipment. It doesn't matter if the cable is charged or if the equipment is charged. It's the potential differential that causes the discharge. ESDEMC develops commercial system for CDE reliability test and evaluation.
-
Product
Battery Chargers
-
DC Battery ChargersStep-Up & Step-Down DC Source Chargers and Equalizers These units provide up to 600 watts to charge a 12V or 24 V battery systems (1 or 2 banks) from a 12, 24, 32 or 36 volt source. The single-board design incorporates state-of-the-art switch mode technology for unmatched efficiency and ultra-quiet operation. Multiple stages of filtering reduce radiated or conducted noise to very low levels. All Series are capable of charging up to two independent banks of batteries.
-
Product
Battery Probes
-
C.C.P. Contact Probes Co., LTD.
CCP offers a variety of different high current battery testing probes.
-
Product
Battery Tester
700
-
The #700 has an internal loading capacity of 100 amps. It is a great tool for finding batteries that can’t stand up to the load of today’s automotive accessories. It will also test relative starter current draw and charging voltage.
-
Product
Partial Discharge Meter
APD-LT
-
The APD-LT equipment is a partial discharge meter in cable accessories (heads or insulators) to improve safety and maintenance. The PD level is presented numerically in the wireless unit.
-
Product
Battery Test
1260
-
*Basic Battery Load Test*Battery Analysis*Mac*Test*Bad Cell Indicators*Testing the Starter Motor*Low Temperatures Effects
-
Product
Battery Chargers
-
Electronic Test & Power Systems
Our dedicated range of battery chargers support Ni-Cd, Ni-MH, Li-ion and lead acid chemistries. Industrial lead acid battery chargers with temperature compensation are available at a variety of voltage levels and output powers. The high conversion efficiencies result in a small case style making the BC-SMPS product family ideal for system integration.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, Simplified Current Sink, 750 V Isolation
43-752A-901
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Partial Discharge Test Set
-
We are an unparalleled name in the industry, engaged in manufacturing and exporting Partial Discharge Test Set that is broadly used for instrument transformers to test the discharge of voltage. This test set is manufactured in compliance with set international quality standards using optimum quality components under the observations of our experienced professionals. Further, it is made available in several specifications to meet the exact requirements of the clients. Our offered Partial Discharge Test Set can be owned from us at nominal prices.
-
Product
Standard 0.95 (26.90) - 4.50 (128.00) Battery Probe
CP-2SB-12
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 128Full Travel (mm): 3.25Recommended Travel (mil): 118.1Recommended Travel (mm): 3.00Overall Length (mil): 472Overall Length (mm): 12.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
Battery Charger/Analysers
MB73P+
-
Charging 12V at 50A Or 24V at 25ACapacity Test: 12V at 60A Or 24V at 50AConstant Voltage ChargeConstant Current ChargeConstant Current 4 Step Charge – Steps Can Be Used As Rest Periods
-
Product
Battery Monitor
BAF-M2
-
Schumacher Electric Corporation
BATTERY MONITOR• Plugs into a 12 volt automotive cigarette lighter receptacle• Allows instant monitoring of battery & charging system voltage• Constant automotive battery and charging system check with a digital readout• LED warning lights alert you when your battery or charging system is not functioning properly• Detects charging input voltage within 0.1 volts variance• Detects problems with the alternator, diode and any variance of more than 0.8 volts• Alerts you once battery drops to 12.0 volts giving you approximately one more hour of run time, depending on the system’s wattage• Digital display indicates electrical voltage of your battery• Mounted display on your car’s dashboard for constant monitoring of your electrical system Contents: (1) Battery Monitor with 12V DC plug
-
Product
CP-059-025 Battery Probes
Battery Probe
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 57Full Travel (mm): 1.45Recommended Travel (mil): 40Recommended Travel (mm): 1.02Mechanical Life (no of cyles): 100,000Overall Length (mil): 313Overall Length (mm): 7.95
-
Product
Battery Gauges
-
Global Digital Instruments, LLC
Our battery fuel gauges and LED volt meters are designed to monitor the charge capacity of DC powered equipment and monitor information about the equipment's electrical system.
-
Product
PARTIAL DISCHARGE test set
pdnt02
-
International Biological Laboratories
This Test Kit is used for non-destructive means of assessing the quality of high voltage transformers, motors, cables etc., which are used in generation & distribution of electric power.
-
Product
Superior Handheld Partial Discharge Detector
PDStar
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT is proud to present one of our latest innovations, the PDStar. It integrates On-Line Partial Discharge (OLPD) testing and Infrared testing for MV and HV equipment, which combines UHF, AE, Ultrasonic, HFCT, TEV, and Infrared testing technologies. It is applicable for online PD testing, as well as abnormal heating and defect detection on all types of substation equipment. PD amplitude, PRPD, PRPS, and infrared spectrums provide critical data for determining the operational condition of electric power equipment. It connects to the PMDTCloud via Wi-Fi/3G/4G to upload test data, download test tasks, and receive diagnostic results in real time. Another uniquely advanced feature of the PDStar is that it integrates with a 100 MSPS (Mega-Samples per Second) HFCT signal processor, which greatly improves the performance for power cable OLPD testing.
-
Product
Battery Chargers
-
Xantrex battery chargers are micro-processor controlled for fast, accurate charging of vehicle or boat batteries in deep cycle or maintenance applications. Xantrex battery chargers are compact, light weight and easy to install.
-
Product
Counter Battery
-
This all fuels the need to redefine effective approaches in counter battery, in particular for the functions usually fulfilled by weapon location radars: target acquisition, fire control and prediction of impacts.
-
Product
Battery and Capacitor Testers
-
Battery test system developed on the basis of the experience and know-how that we have amassed through implementing numerous custom-built battery evaluation systems.
-
Product
Electrostatic Discharge Generator
SKS-0230I
-
Shanghai Sanki Electronic Industries Co., Ltd.
The electrostatic discharge generator SKS-0230I has high reliability, the host itself can withstand 30kV electrostatic discharge test; 7-inch touch LCD screen, simple interface, convenient operation; unique combination test mechanism, multiple modes, arbitrary combinations of parameters, continuous testing; Equipped with a file management system, which can save commonly used test parameters, and can also import and export test parameters through U disk; has temperature and humidity monitoring function, real-time display of temperature and humidity indicators of the experimental environment; high- pressure precision resistance and capacitance combination, long service life, and Easy to replace to meet different experimental requirements (150pF, 330pF, 330Ω, 2000Ω);
-
Product
Battery Charger-Analyzer for small battery systems (up to 10A-Hr)
24-400xg
-
The 24-400XG is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation of Constant Current Charge (dual and single rate), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge (analysis), Resistance Discharge (analysis) and Full Discharge (deep cycle), the 24-400XG can satisfy the requirements of most small (0 to 10 A-hr) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit (no load) and Overvoltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights inform of the status of the operation.
-
Product
Battery Testing Equipment
-
Mainly for battery testing in lab,such as 5V1mA, 5V10mA, 5V50mA,5V100mA, 5V1A,5V3A,5V6A,5V10A
-
-
Product
Partial Discharge Measurement Calibrator
DAC-CP-2
-
DAC-CP-2 is a calibrator for partial discharge measurements. The electric charge enables to generate up to max 10000pC. It is battery-operated and can be charged by connecting to the measuring instrument (DAC-PD-3).
-
Product
Partial Discharge Measuring Equipment
-
Different from a conventional partial dischargemeasuring set provided with a fixed testingfrequency, Model DAC-PD-5 is newly designed toselect the center and the bandwidth of testingfrequencies so that partial discharges emitting in anoptional frequency in the range of a specifiedbandwidth can be detected. Generally, partialdischarges are measured in a wide band frequencythough; the detecting sensitivity must be lowered inorder to detect partial discharges partially.DAC-PD-5 has a wider bandwidth and can measurepartial discharges in a high sensitivity by bypassingnoises emitting bands.
-
Product
Battery String Simulator
BSS
-
AMETEK Programmable Power, Inc.
The Elgar Battery String Simulators (BSS) provide safe, reliable battery power for spacecraft testing. The broad range of features available ensures simulation capabilities for more than just two terminal power. It's the ideal solution for complete integrated system testing, not just battery elimination.
