Mixers
-
product
Scalar Mixer / Converter Measurements
S97082B
The S97082B scalar mixer/converter measurements enables the highest accuracy for scalar conversion–loss/gain measurements with a simple setup and calibration
-
product
Single Sideband IQ Modulators To 16 GHz
Single Sideband Modulators incorporate a 90° hybrid, 2-way 0° divider and two mixers to produce either an upper (RF + IF) or lower (RF - IF) sideband when driven by a carrier signal and modulation input signal. Depending on the phase relationship of the signals injected into the MOD.I and MOD.Q ports, the modulator will pass either the upper or lower sideband through to the output while rejecting the other.
-
product
Transistor Arrays
Renesas' portfolio of transister arrays include NPN, PNP, NPN-PNP combination transistor arrays based on our complementary UHF-1 SOI process. This portfolio also includes ultra high frequency transistor arrays for VHF/UHF amplifiers, VHF/UHF mixers, IF converters, synchronous detectors. Dual long-tailed pair transistor arrays and Gilbert Cell UHF transistor arrays are also available for wireless communication systems, radio and satellite communications and high performance instrumentation.
-
product
Double-Balanced Mixer, 18 to 46 Ghz
MAMX-011054
Macom Technology Solutions Holdings Inc.
MAMX-011054 is a double-balanced passive diode mixer housed in a 3 mm, 12-lead AQFN package. The mixer offers low conversion loss, high linearity and a wide IF bandwidth. The double-balanced circuit configuration provides excellent port isolation while internal 50 Ω matching simplifies its application. MAMX-011054 is also available in die form. Refer to datasheet MAMX-011037-DIE. This mixer is well suited for applications such as test and measurement, microwave radio and radar.
-
product
Digital Automatic Matrix Mixer
DM1624f
The DM1624F is a powerful digital audio processing, mixing and routing system. The primary applications are sound reinforcement and conferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency.
-
product
Differential And I/Q Device Measurements
S97089B
The S97089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers
-
product
Hot Electron Bolometer (HEB) Mixers/ Receivers In Terahertz Range
Insight Product Company offers Hot Electron Bolometer (HEB) mixers, receivers, and chips made from NbN or NbTiN thin film. The HEB mixers can operate at frequencies of up to several terahertz.
-
product
Digital Camera Hop Transmitter
DCHT
The DCHT portable digital stereo transmitter is designed for use in film and TV production as both a wireless audio link from a bag or cart system to cameras and as a portable IFB transmitter paired with the Duet digital wireless M2R receiver packs. The DCHT accepts two channels of mic or line level analog signals or an AES digital signal from a mixer and transmits to the receiver or receivers in a purely digital format. The digital architecture of the new DCHT is a third-generation design with specially developed, high-efficiency circuitry for extended operating time on two AA batteries.
-
product
Full Band Noise Figure and Gain Test Extenders
STG-06-S1
Full band noise figure and gain test extenders are offered to extend noise and gain measuring capabilities up to higher millimeterwave frequency ranges. These extenders are designed to interface with noise and gain test systems that have an input IF of 10 MHz to 1.6 GHz, such as the industry standard Keysight 8970A/B, N8975A and Maury MT 2075B. The noise figure and gain test extenders include a high-performance, solid-state noise source (STZ series) and a full waveguide down converter (STC series), which consists of a Faraday isolator (STF series), full band mixer (SFB series), frequency multiplier, and IF amplifier. A frequency source with an output signal in the frequency range of 10 to 20 GHz is required as a local oscillator for the down converter. The noise source is automatically powered on and off by the noise figure meter.
-
product
Mixed Gas Generators MU Series
MU-2200
The mixed gas generator MU Series integrates with high-performance mass flow controllers to generate a homogenous gas mixture of two or more types of gases. Using the control unit’s touch panel you can control both flow rate, and the concentration of the mixed gas.The gas generators can be used for industrial purposes, such as generating combustion gases supplied to burners, as well as laboratory use in the biotechnology and food markets. HORIBA produces gas mixers tailored to customers’ intended uses, such as models with a purge function capable of mixing reactive gases.
-
product
Millimeter-wave and Microwave GaAs Mixers
Keysight Technologies provides MMIC mixers ideal for microwave radio, aerospace and defense, and instrumentation applications.
-
-
product
Gas Mixers
Get the right gas mixture and flow rate using our Gas Mixers for Modified Atmosphere Packages. We offer gas mixers for CO2, Oxygen, Nitrogen, and Argon gases.
-
product
3GHz to 20GHz Microwave Mixer with Wideband DC to 6GHz I
LTC5552
The LTC®5552 is a high performance, microwave double balanced passive mixer that can be used for frequency upconversion or downconversion. The device is similar to the LTC5553, but with a broadband, differential DC to 6GHz IF port. The LTC5552 is recommended for applications where the IF frequency range extends below 500MHz. For applications where the IF frequency is always above 500MHz, the LTC5553 is recommended, since it includes an integrated IF balun.
-
product
Radar Front Ends (FMCW)
FMCW Series
Farran’s 77 GHz FMCW Radar front end is based on a GaAs MMIC chipset offering wide bandwidth in a small outline package.The transmit signal is derived from an external VCO signal, internally multiplied, which also acts as the LO for the receive mixer. The resulting IF is conditioned for gain and filtering as required. The IF also contains an industry leading IF noise figure, especially in the frequency range below 500MHz. Custom designs available, visit our custom design page for more information.
-
product
Waveguide Harmonic Mixer (smart mixer), 75 to 110 GHz
M1971W
Keysight M1971W 75 to 110 GHz waveguide harmonic mixer is an un-preselected mixer that provides a complete solution for wideband millimeter-wave signal analysis of more than 2 GHz with X-Series signal analyzers. Embedded smart features help you to greatly simplify your overall test setup and improve the DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
product
DI Boxes
Applied Research and Technolgy
Instrument DIs for stage and studio, plus specialized tools to connect virtually any source to a mixer, interface, or PA.
-
product
Mini Receiver
FB7-NX
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
product
Schottky Mixer and Detector Diodes
Macom Technology Solutions Holdings Inc.
Schottky diodes are majority carrier diodes formed by plating a layer of metal on a layer of doped semiconductor, which forms a rectifying junction. The type of metal and the type of dopant in the semiconductor determines the diode’s barrier height, which is a measure of the amount of energy required to force the diode into forward conduction. MACOM produces Si Schottky diodes as well as GaAs Schottky diodes for use as signal detectors or in frequency mixers.
-
product
Integrated Couplers/ Harmonic Mixers
These waveguide bandwidth integrated coupler/mixers are designed to allow phase locking or signal monitoring of compact millimeter wave systems. RF inputs and outputs are on opposite sides of a thin wafer to obtain minimum insertion length. These devices use silicon Schottky barrier beam-lead diodes on a rugged stripline circuit. Nominal coupling value is 10 dB. For coupling values greater than 10 dB, non-directional coupler models are available (consult factory).
-
product
Frequency Expansion Modules
bsw TestSystems & Consulting AG
Up To 1.5THz For Network Analyzers Modern communication standards, like for instance 5G, place high demands on components (mixers, amplifiers, antennas, etc.), which have to be examined in high frequency bands (millimeter waves); the requirements include: broad frequency coverage, sufficient output power to operate the components under compression, high dynamic range and stability as well as a reduced dynamic content within the spectrum.
-
product
Scalar Mixer / Converter Measurements
S95082B
The S95082B scalar mixer / converter measurements software provides an intuitive and easy-to-use user interface for setting up mixer and converter measurements with single or dual conversion stages. It controls the analyzer’s built-in source(s) and external signal generators for use as LO signals.
-
product
2x8 QPSK Mixer
To be used for optical coherent detection such as DP-QPSK receivers, Optoplex’s ten-port 2x8 Coherent Mixer (aka QPSK mixer) combines the incoming signal with a local oscillator to generate eight light states in the complex-field space. The eight light output signals can then be coupled into four pairs of balanced detectors. The block diagram below shows the application of a 2x8 coherent mixer in a DP-QPSK receiver. Since the mixing process is data rate independent, the devices can be used for any data rate in applications such as 40Gb/s or 100Gb/s transmission systems.
-
product
I/Q and Image Reject Mixers
In-phase quadrature (I/Q) mixers and image reject mixers (IRM) offer a robust frequency mixing solution for applications that require high image rejection or sideband suppression. These mixers can be used as an upconverter or downcoverter. I/Q or IRM mixers use two double-balanced mixers with a 90° hybrid. The inherent architecture of I/Q mixers eliminates the resulting product due to image frequency during downconversion and allows the selection of desired sideband during upconversion.
-
product
Differential And I/Q Device Measurements
S93089B
The S93089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers
-
product
Harmonic Mixers
These waveguide bandwidth harmonic mixers are designed for use with spectrum analzyers with diplexers, such as the Tektronix 492 and 494 and the Hewlett-Packard 8555A, 8565A and 8569A. They are also used as phase locking and receiver mixers for antenna measurement systems such as the Scientific Atlanta wide range receivers. When used with an external diplexer*, these harmonicmixers can be used to phase lock millimeter wave sources.
-
product
Disposable Square OptiMixers
Optimizing mix performance in a 20% shorter length than comparable square mixers, the OptiMixer™ allows users to get even closer to applications.
-
product
17 To 19 GHz QPSK Modulator
CCM19001
The CCM19001 is a Differential Drive Digital QPSK (Quadrature Phase Shift Keying) modulator operating across the 17.0 to 19.0 GHz frequency range. The modulator utilizes differential drive digital inputs (180º apart) to drive both of the bi-phase modulators (mixers) integrated into the assembly. The modulator is a combination of a matched pair bi-phase modulators, which are in quadrature (90º) to each other. It is modulated by switching polarities of the DC voltage controls in 4 different logic states ("0,0", "0,1", "1,0" & "1,1") for 4 phase states. The QPSK modulator provides constant amplitude, 90º vector: 0 (ref.), 90º, 180º, 270º and operates across the -55º to 85º C temperature range.
-
product
Honey Refractometer
BKPR-2
Measure honey moisture content plus honey solids content with the MISCO Digital Honey Refractometer. The honey refractometer is designed for government honey inspectors, professional beekeepers, honey producers, honey mixers, honey brokers, or anyone requiring the absolute most accurate, repeatable readings of honey moisture content and honey solids content.
-
product
Downconverter
MADC-011021
Macom Technology Solutions Holdings Inc.
The MADC-011021 is a surface mount E-band receiver. The module operates from 71 - 86 GHz and is designed to be used in direct conversion or heterodyne applications. The RF input is a WR12 interface. The module provides 12 dB of conversion gain and a noise figure of 5 dB. The linear mixer topology allows for strong IIP3 performance (2 dBm) to be maintained up to the radio input levels recommended in the standards. The baseband is a quadrature balanced four line interface (I, I*, Q, Q*).
