-
Product
Cigarette Lighter Socket Sensor
FT-0801
-
The FT-0801 cigarette lighter socket sensor detects ignition noise of voltage from cigarette lighter socket sensor as rotation signal. Useful for signal detection from a cigarette lighter socket equipped in an automobile or construction machinery.Rotation signal can be detected from a cigarette lighter socket by using the FT-0801 even if it is difficult to attach a rotation detector inside of an engine room.
-
Product
NI-9217, 4-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
779592-01
Temperature Input Module
4-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9217 is a resistance temperature detector (RTD) input module. You can configure the NI‑9217 for two sample rate modes: high sample rate or high resolution. The NI‑9217 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9217 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Flux Leakage Tester For Detecting Surface Defects In Hot Rolled Black Steel Bar
130MM ROTOFLUX® AC
-
Highly sensitive AC flux leakage is especially well suited to test hot rolled black steel bars and rods that have surface conditions which used to make finding shallow defects very difficult, if not impossible.
-
Product
Drill Guides
ExitPoint® XL300
-
Accurately detect exit points before drilling and coring with the Zircon® ExitPoint® XL300 through-hole drill guide. The XL300 is the easiest and fastest way to locate a precise spot, without measuring, before you start your project.
-
Product
Fineliner
-
The parallel tester Fineliner enables two-sided contact with fne structures. Withvisual detection of both substrate sides and corresponding adapter position correction≥ 300μm test points can be contacted. The rigid needle adapter with a pitch of ≥ 400μmalso allows a high contact density. This results in a large test depth on the substrate.The integrated DMC reader ensures a correct test result assignment. Multiple PCB canbe tested step by step through in the X-direction of the Fineliner, further eliminatingsubstrate tolerances in the X-direction, and enabling more cost-effective adapters andmeasurement techniques. A quick-release system with identifable replacement kitsensures safe and quick retooling.The measuring technology can be defned customer-specifcally. There are 2040 pyloninterface points per side.
-
Product
Scanning Electron Microscopy (SEM Analysis)
-
Rocky Mountain Laboratories, Inc.
Scanning Electron Microscopy (SEM Analysis) can produce images of almost any sample at magnifications of 15-300,000X. The SEM has tremendous depth of field allowing for imaging that cannot be accomplished using optical microscopy. Conductive and nonconductive samples can be imaged. When operated in the backscatter (BSE) detection mode, differences in material composition can be observed. Elemental analysis can be performed on any feature observed with an integrated Energy Dispersive Spectroscopy (EDS) detector.
-
Product
Environmental Stress Screening (ESS) Chamber
ESS
-
Developed to help electronics manufacturers detect product defects and production flaws, Environmental Stress Screening (ESS) forces infancy product failures that would otherwise occur after final assembly and product delivery. ESS’s goal is to improve profitability by eliminating defective products. ESS Systems can meet individual performance needs, product loading, and throughput requirements. Thermotron has the experience to provide the best solution for ESS testing at your company.
-
Product
Fire Extinguishers Testing Equipment
-
The circular electrode brush passes easily through the neck of the extinguisher cylinder and then expands to make reliable contact with the lining. Faults are detected by the voltage jumping from the electrode to the earthed shell, causing an alarm to sound. Special electrodes are available specifically for this application.
-
Product
Medical Box PC
-
ADLINK’s medical box pc, compliant with IEC 60601-1 (3.2 edition) / IEC 60601-1-2 (4.1 edition) for safety and performance of medical equipment, is designed to build in space-limited medical devices, such as C-arm and surgical navigation system. The medical grade platform features ADLINK’s MXM Graphics Module supporting NVIDIA GPU, ensuring the acceleration of image reconstruction and beamforming and moreover, significantly reducing data transmission delay, lowering latency and enhancing image quality with AI to assist doctors in detecting diseases or other abnormalities.
-
Product
Zero Touch WAF
-
Unpatched software is still considered a dangerous gateway for cybercriminals today. The use of global exploits is not decreasing; the numbers keep increasing. To avoid relying on software support, you should rely on our Zero Touch WAF, which detects and stops such unwanted events.
-
Product
Disconnection Detector for PV
NSEI-100D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*This device can detect the disconnected & broken point of DC current lines between PV panels and power conditioners in PV systems, without cutting power off and without climbing the roof where PV modules are located.*Furthermore, this model can find out the disconnecting point by applying the attached detector to the specific PV module.
-
Product
Phantom Vent Tube Metal Detector
-
The Phantom Vent Tube metal detector is primarily designed to detect and track a fallen vent tube nozzle inside a bottle that is conveyed through bottle-processing equipment. The convenient retrofit design allows for easy installation into existing bottling lines. Built from stainless steel (304) material and totally enclosed for washdown purposes, the detector phases out the conveyor belt and maintains a steady sensitivity.
-
Product
Ultrasonic Flaw Detector
MFD620C
-
The MFD620C is an advanced digital ultrasonic flaw detector featuring a multi-color TFT LCD and a host of new features to meet challenging inspection requirements. It combines powerful flaw detection and measurement capabilities, extensive data storage, and the ability to transfer detailed inspection data to the PC via its high-speed USB port.
-
Product
Metal Detector
-
STAR TRACE SOLUTIONS PVT. LTD.
Metal detectors are one of the must haves for any food processing unit irrespective of their size. They play an important part in determining the quality of the merchandise in addition to many others.The Metal Detector designed by Star Trace Pvt. Ltd. Chennai ( Tamilnadu, India) for Food Processing Industry are highly efficient in detecting ferrous, non-ferrous and stainless steel contaminants ranging in different sizes and shapes. Taking into consideration.
-
Product
AI-based Test Generation
-
Our AI-based test generator can automatically automate your tests. Using recheck-web, these tests not only detect functional differences, but also visual differences.
-
Product
Fixed Digital Gas Detector
OLCT 10N
-
Teledyne Gas & Flame Detection
The OLCT 10N is a digital combustible gas detector designed for to detect combustible, toxic gases or oxygen. Intended for use in combination with the MX 16, MX 32 and MX 43 controller, the OLCT 10N provides a fast and accurate response.All transmitter information is received by the controller in less than 1 second.Non-intrusive operator interface requires only a simple magnetic wand and allows one man calibration without opening the enclosure.
-
Product
Counterfeit Defect Coverage Tool
-
The SAE Counterfeit Defect Coverage Tool is a dynamic, web-based application that supplements SAE Standard AS6171 authored by the SAE G-19A Test Laboratory Standards Development Committee. It provides potential test sequences for the identification of counterfeit electrical, electronic, and electromechanical (EEE) parts along a range of risk levels and EEE part types. Allowing users to compare alternative test sequences as a function of resources needed to implement those tests, the SAE CDC Tool is appropriate for those ordering counterfeit detection tests as well as those performing the tests.
-
Product
EasyClassify
-
Includes functions for classifier training and image classificationAble to detect defective products or sort products into various classesSupports data augmentation, works with as few as one hundred training images per classCompatible with CPU and GPU processingIncludes the free Deep Learning Studio application for dataset creation, training and evaluationOnly available as part of the Deep Learning Bundle
-
Product
Chemiluminescence NOX-NO2-NO Analyzer
Model N200
-
Teledyne Advanced Pollution Instrumentation
The Model N200 uses the proven chemiluminescence detection principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of low-level Nitric Oxide (NO), Nitrogen Dioxide (NO2) and total Nitrogen Oxides (NOx) gases.
-
Product
VOC Detectors
-
The Baseline® VOC-TRAQ® II detector is a handheld VOC sensor designed for ease of use and is an excellent way to monitor and record PID detectable total volatile organic compounds (TVOCs), whether you are an air quality consultant, safety engineer, maintenance manager, or just concerned about TVOCs in your environment. This Baseline VOC detector includes:
-
Product
Radar Flow Meter
HR.FSL-1
-
HighReach Measuring & Controlling System Co.,Ltd
It is designed for combination with water flow detection for hydrological monitoring. It is designed for surface flow monitoring of natural rivers, canals/cules/pipes, etc., and flood monitoring in urban Seasons Flood, SUCH AS Low-lying Areas. Water Flow, Flow Rate Monitoring Drain, etc. of The Product Planar absorbs The 24GHz Radar Technology of a microstrip InnoSenT of Germany, and Adopts ITS own Back-End Processing Technology to Accurately The Water Extract Flow Speed , which can realize non-contact and unmanned automatic monitoring.
-
Product
Close Contact Confirmation Switch
HPS/MHPS/UHPS
-
High precision needle mechanism enables highly accurate detection such as contact confirmation.In addition, various special nozzles can be applied to various position detections.
-
Product
Thermal Security Camera with Onboard Analytics
Triton™ F-Series ID
-
The FLIR Triton™ F-Series ID thermal security cameras set the new standard of perimeter protection for critical infrastructure. The Triton F-Series ID features best-in-class thermal imaging detail and high-performance onboard analytics for classifying human or vehicular intrusions. FLIR’s premium line offers five models with full 640 × 480 thermal resolution, longer detection ranges, and better analytics performance than ever before.
-
Product
X-ray Analytical Microscope Super Large Chamber Model
XGT-9000SL
-
- Large chamber capacity (W x D x H) : 1030 mm x 950 mm x 500 mm- X-ray shield complying with JAIMAS0101-2001/ IEC1010-1 to protect you from X-ray exposure- Mapping area size up to 350 x 350 mm2- <15 µm spot size with ultra-high intensity without compromising sensitivity and spatial resolution- Dual types of detectors for transmission and fluorescent X-rays- Detectable element range down to C with a light element detector and He purge module
-
Product
Transceivers
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer monolithic and stereo Doppler transceivers for directional motion detection. Our transceivers are used in a variety of applications such as automatic door openers, ground speed recorders and police radars. MACOM’s transceivers are well suited for high volume applications where small size and reliability are required.
-
Product
RF Generators
-
Produce radio frequency (RF) signal for device evaluation and fault detection.
-
Product
Wheel Torque Transducer
WTT-Dx
-
In automotive development, it is important to know the exact torques acting on the vehicle – especially under acceleration and braking maneuvers. With the WTT-Dx wheel torque transducer, a high-precision tool is available for making such measurements. The WTT detects the mechanical load directly where it is produced: the wheels that form the interface between the vehicle and the road.
-
Product
FlexMobile 429+
-
The FlexMobile 429+ is a lightweight and portable device that supports ARINC 429 and Discrete, with precise timing and flexible programming. It comes with various ARINC 429 options, 28V open-collector Discrete Inputs/Outputs with software-selectable directions and Ethernet/USB connectivity. It also has extensive error injection and detection capabilities, 10 ns timing accuracy, and support for various software interfaces such as Multibus, MX-Foundation 4 API, MAXIM GUI, and MAXIM Air GUI. The device also supports synchronization with other FlexMobile devices and IRIG-B Sync.
-
Product
Portable Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuit and will possibly prevent serious damage to plant or injury to personnel. Apart from checking the protective circuits correctly, it is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay tester.
-
Product
Digital Luminosity/Lux/Light Sensor Breakout
TSL2561
-
The TSL2561 luminosity sensor is an advanced digital light sensor, ideal for use in a wide range of light situations. Compared to low cost CdS cells, this sensor is more precise, allowing for exact lux calculations and can be configured for different gain/timing ranges to detect light ranges from up to 0.1 - 40,000+ Lux on the fly.
