Filter Results:
Products
Manufacturers
Applications
Motor Test
See Also: Motor
-
Product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-01
Voltage Input Module
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
Product
Peel Testers
-
Imada offers motorized peel testers in vertical or horizontal configurations.The motorized test stand, digital force gauge and peel fixture apply tension to a safety seals, tapes and laminates.Special attachments and fixtures facilitate 45°, 90°, 180°, ‘T’ and rotary peel tests.Motorized peel testers offer speed control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All peel testers with digital force gauges have data output capability for analysis by optional data acquisition software.
-
Product
Cogging Test System
CTS
-
Magtrol’s Cogging Test System is a stand-alone test system designed to control and measure Detent Torque, Cogging Torque and Friction Torque. The test System includes a precision geared motor, a TS Series Torque Sensor integrating a 5 000 pulses encoder. CTS 100 to CTS 102 have a built-in security clutches to avoid system overload by mishandling when not in use. The geared motor drives the MUT (Motor Under Test) at a low speed from 1 to 10 rpm (respectively 8 rpm for CTS 103 and CTS 104), while acquiring its cogging torque related to angle position.
-
Product
Brushless/Servo/Stepper Motor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to brusheless, servo,stepper motor performance test.
-
Product
Resistor Simulation Card
SET-1210
-
The card has two ranges of values that meet the requirements of most functional test systems.The SET card is designed for applications in which resistive sensors provide information about parameters such as temperature (e.g. when testing motor controls)Each channel of the SET-1210 resistor simulation card is able to simulate the common short-circuit and no-load conditions, which can occur in a system due to faulty wiring or sensors.
-
Product
Series and EOL Testing of Electric Motors
-
Highly automated EOL test system for blind motors*Test station with fully automatic mechanical and electrical contacting *Scanning the product coding with barcode scanner*Integrated label printing, additional error printer*Contact protection by light curtain
-
Product
Standalone OLTC Event Recorder – OTM-X
-
The OTM-X is the only standalone recorder using the vibro-acoustic method and motor current testing to detect ONLINE your On-Load Tap Changer’s (OLTC) malfunctions.
-
Product
Testing Aerospace Motors
-
Magtrol designed this Custom Motor Test System for the testing of various aerospace motors for both commercial and military applications.
-
Product
Signature Surge Testers
TS Model
-
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
AC Power Source
6500 series
-
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
Product
Testing Wiper Motors
-
Magtrol developed two automatic testing benches for front wiper motors, rear wiper motors (pendulum with measure of angle) and ABS motors (excenter). The test setup is equipped to handle torque ratings from 3 to 50 Nm and a speed range of 0 to 10,000 rpm
-
Product
Electric Motor QC Systems
-
Megger Baker Instruments designs and manufactures electric motor test systems for original equipment manufacturers (OEMs) that help ensure their motors, generators and coils meet or exceed the quality expectations OEMs set with their customers. Baker motor quality control (QC) systems include the Baker WinAST automated stator tester, the Baker HV WinAST and the Baker WinTATS traction armature test system. Each incorporates the most effective electric motor test processes into a single automated instrument and can be customized to meet the specific testing needs of a given manufacturer.
-
Product
Motorized Test Stands
-
The Chatillon motorized test stands are optimized for production floor operation.
-
Product
Motorized Bending Testing Machine
GW-A Series
-
Jinan Testing Equipment IE Corporation
GW-A series motorized bending testing machines are special equipment for bending test on reinforce bar, steel bar, and pipe etc. The motorized bending testing machine can do bending test in both directions according to the standard requirement. The motorized bending tester conforms to standards including ASTM A615, ASTM A615M, ISO 7438, and ISO8491 (E) etc.
-
Product
Efficiency Test
-
Type test stands for industrial electric motors*Testing of 1-phase and 3-phase asynchronous and synchronous motors up to 3 kW*Speeds up to 30000 1 / min
-
Product
Motor Testing Panels
-
Aarohi Embedded Systems Pvt. Ltd
AAROHI Filly and Partially Automatic Motor Testing Panels
-
Product
Circuit Tester
69105
-
Tests circuits rated from 80 to 600 volts AC/DC.High-visibility neon lamp indicator.High-impact, sealed 5-11/16'' (144 mm) probes on long 24'' (610 mm) leads for convenience in testing motors, fuses, relays, switches, etc.Resistor between each probe and lead.Reliable electronic components.
-
Product
High Power Laboratory Testing System
FTF-HP
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery PacksBi-directional DC power supply
-
-
Product
Pump & Motor Testing Instruments
-
Aarohi Embedded Systems Pvt. Ltd
AAROHI Pump and Motor Testing Instruments - dynanometer, stator rotation direction detector, digital RPM meter, DC power analyzer, motor analyzer.
-
Product
Insulating Oil Testers
US, A, AD Series
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Confirms to IS 6792, IEC 156 • Tests insulating oils to IS, IEC, ASTM, etc.• Test voltage to 100kV• Motorized rise of test voltage: 2kV/sec • One piece construction with safety interlocked transparent hood covering test cell• Test voltage can be held at any desired level• kV meter continues to indicate breakdown voltage even after breakdown• Light weight: 36 kg only• Portable, rugged and with cover.
-
Product
Transmission Performance/Endurance Test System
-
This system is suitable for vehicle drive test with only the transmission unit in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling engines, tires or vehicles other than transmission. The engines, tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
Product
Testing Electric Pump Motors
-
This Custom Motor Test System is designed for the testing of 5 different sized electric motors used in various sump, utility, sewage, well, pool and pond pumps. All of the components mentioned above are mounted on a versatile table that can be easily reconfigured and retrofitted to any Magtrol dynamometer.
-
Product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-02
Voltage Input Module
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
Product
Signature Surge Tester
TSM
-
Compact cabinet that contains a multi-position carry/tilt handle and a rear plastic snap-on cover for cable storage and transportation in the shop or in the field. Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope and includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
Alternator Tester
QME-2D
-
Changzhou Chanlon Electronic Technology Co., Ltd.
This tester is applied to fast test generator performance. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing generator (test items difference appear in the different types motor)Test standard.
-
Product
Wireless TRMS Clamp Meter w/ 3-Phase & Imbalance Motor Tests
DL599
-
UEi Test & Measurement Instruments
TRMS Wireless Clamp Meter w/ 3-Phase & Unbalanced Load Tests
-
Product
On-Line Electric Motor Analyzer
EMAX
-
We understand that shutting down electric motors for testing can be time consuming and costly. With the EMAX technology you can now test a motor while it is operating with no interruption to production. Within seconds the EMAX will provide a comprehensive detailed look at the Power Circuit, Power Quality, Stator, Rotor, and Air Gap.
-
Product
Test Stands: Mechanical and Motorized
-
SHIMPO offers both motorized and mechnical test stands suitable for the most precise testing applications.
-
Product
Motor/Generator Test Equipment
-
Winding ohmmeters RMO-M series measure winding resistance of inductive test objects such as electrical motors and generators. Motor test or generator test of winding resistance is especially important for early-stage failure detection.RMO-M series instruments generate true DC ripple-free current with automatically regulated measurement and discharge process. Even more, test instruments are portable and enclosed in a metal casing.Applications supported by DV Power motor/generator test equipment include:Winding resistance measurement of generators and electrical motorsResistance measurement of high-current bus bar jointsResistance measurement of cable splicesAll of the above-mentioned measurements are performed with the highest accuracy. The advanced DV-Win PC software enables collecting both numerical and graphical results. These features provide an easier and more efficient analysis. After the test, a DV-Win software generates a test report a single click. Finally, a user can easily customize the report and save it in different formats, such as XLS and PDF.
