CAT
Computer Aided Test
-
product
Infrared Thermometers
Instant, less-than-a-second temperature readings of any surface, °F/°C switchableIdeal for food preparation, pharmaceuticals, field use, electronics, and safety inspectionFeatures minimum/maximum memory, average readings, and high/low audible alarms (Cat. No 4484)
-
product
Test Leads
AL-34WB
Standard Electric Works Co., Ltd
● Wire length: 1.2m approx. Silicone insulated wire (1000mm) with wire connected to straight input plugs (130mm PVC wire), and wire for clamp (100mm PVC wire). ● Outside diameter of silicone insulated wire: 5mm Outside diameter of PVC wire: 3.5mm● Input plug color: Red•Green•Black•Blue ● Current rating: 5A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
-
product
Digital Insulation Mult-Meter
8010 IN
Standard Electric Works Co., Ltd
● Microprocessor controlled.● Four insulation test voltages (DC) : 125V, 250V, 500V, 1000V● The maximum insulation measurement range is 200G ohm @1000V.● 1mA test current on insulation test at nominal voltage.● With a hand strap for easier holding.● Large LCD (78 × 67mm)● Auto-ranging.● Bar-graph indication.● Backlight function.● REL(Auto-null) function.● Auto AC/DC voltmeter.● Capacitor test.● Auto-test stop & smart hold.● Supplied with high quality test leads.● Safety standard : EN 61010-1 CAT III 600V IEC 61557-1 IEC 61557-2 EN 61326-1
-
product
Handheld TDR / Cable Fault Locator
RapidTrace 1100
*This TDR / Cable Fault Locator is suitable for testing all Communication CAT (3-6) , Power Cabling , coaxial and mains power cabling*The RapidTrace 1100 TDR / Cable Fault Locator has a 11 measurement ranges from 0.5m to 3500m (3.5km) and is accurate to 1%*The TDR / Cable Fault Locator has 25, 50, 75 & 100ohm Selectable Cable Impedances*Using pre determined gain and pulse width on the TDR / Cable Fault Locator, all major operating and setting parameters can be easily accessed
-
product
High Voltage Probe
HVP-40
*MAX. Voltage : DC : 40KV, AC : 28KV, (50/60Hz only) CAT II.*1000MΩ Input Impedance.*Accuracy **DC: ± 1% to 20KV. ± 2% to 40KV. **AC: -5% to -10% (50/60Hz)*Division Ration : 1000:1*CE, TUV GS, UL, CUL, IEC1010
-
product
Digital Insulation Mult-Meter
8005 IN
Standard Electric Works Co., Ltd
● Microprocessor controlled.● Four insulation test voltages (DC) : 50V, 100V, 250V, 500V● The maximum insulation measurement range is 200G ohm @500V.● Large LCD (78 × 67mm)● Auto-ranging.● Bar-graph indication.● Backlight function.● REL(Auto-null) function.● Auto AC/DC voltmeter.● Capacitor test.● Auto-test stop & smart hold.● Supplied with high quality test leads.● Safety standard : EN 61010-1 CAT III
-
product
Magnet Testing
m-cat
m-cat is a magnetic field mapper for magnetrons which measures the magnetic stray field data of magnetrons on all three spatial axes and also calculates geometric data. This allows sputtering processes to be monitored and optimized, since the setting or status of the magnetron is critical to the subsequent outcome of the coating process.
-
product
Handheld Circuit Breaker And Timer Analyser
CAT-H Series
The operation of the breaker can be initiated in different ways (e.g. from a control room, by a local breaker or externally by a test device) depending on the test conditions. Various time measurement triggers are available to record a measurement under a different test condition:*Coil control channel*Continuous current clamping channel*DC voltage channel
-
product
Bench-top Microreactor & Combined Mass Spectrometer System
CATLAB-PCS
The Hiden CATLAB is a bench-top microreactor and combined mass spectrometer system for rapid and reproducible catalyst characterisation and reaction studies. The modular benchtop system features an advanced fast-response low thermal mass 1000oC furnace, multistream gas flow control of up to eight integrated gas streams, together with the precision Hiden quadrupole gas analyser.
-
product
Rechargeable Multifunction Tester
ET4000
The new ET4000 tester carries out all the tests needed to verify the safety of electrical installations in domestic, commercial and industrial wiring installations in accordance with the latest regulations.
Everything about the new ET Series has been designed to save time and make testing easier.
Fast, reliable high current and non-trip loop testing comes as standard together with a high level of input protection and a CAT IV safety rating .
Supplied with a full range of accessories.
-
product
Double Display TRMS Multimeter with USB Interface
VA42 VA42R VA42RP
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
This instrument complies with IEC 61010-1:2001, CAT II 1000V and CAT III 600V overvoltage standards. See Specifications.
-
product
Product Design and Experience
Catia
CATIA delivers the unique ability not only to model any product, but to do so in the context of its real-life behavior: design in the age of experience. Systems architects, engineers, designers and all contributors can define, imagine and shape the connected world.
-
product
Circuit Breaker Analyzer
CAT Standard Series
The CAT Standard series circuit breaker analyzers & timers are stand-alone or a PC-controlled digital instruments for circuit breakers condition assessments. The timing channels record closing and opening of the arcing, resistor, and auxiliary contacts. CAT Standard series records graphs of both, trip and close coil currents and displacements of the HV and MV circuit breaker moving parts. The main contact channels can also measure the resistance value of the pre-insertion resistors (if present in the circuit breaker). Test results can be downloaded to a USB memory stick or saved to internal memory. The CAT Standard series internal memory can store up to 500 test results (numerical and graphical data). Test results can also be printed on the 80 mm (3.15 inch) thermal printer (optional accessory) in tabular and graphical form. CAT Standard series provides an easy selection of different operational modes:
-
product
Compact Manual Ranging 600V Multimeter
DL9204
Compact manual ranging digital multimeter with 2000 count LCD display. Full protection on all ranges, safety category to CAT 111 600 V. Functions include battery and diode test.
-
product
RJ45 (Ethernet 100 Base T) to 90 Series Interface (R)
J90RJ45R
RJ45 Ethernet connector for VPC Tripaddle 90 series RCV moduleUp to three connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
-
product
Cable Testers
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
product
Multimeters
Whether you work in industrial, HVAC, commercial or residential electrical environments, there’s an Amprobe digital multimeter with features to match your requirements. From heavy-duty industrial Amprobe DMMs with CAT IV safety ratings, to pocket size meters that handle all the basics, Amprobe makes some of the best digital multimeters around. Whatever your application, there’s an Amprobe multimeter ready to get the job done.
-
product
Testing Large Radar Sensors with CATR Technology
CATR Radar Test System UTP 5069
Modern driver assistance systems must recognize increasingly complex traffic scenarios and convert them into appropriate vehicle reactions with the help of artificial intelligence (AI) and specific algorithms. Imaging radar sensors with a higher spatial resolution, so-called imaging radar sensors, are therefore required. These can better distinguish larger from smaller objects and, due to the larger antenna apertures, also require larger dimensions of the test environment or larger far-field distances. Testing these sensors in the direct far field ( UTP 5065 ) would therefore require very large absorber chambers up to ten meters in size and more.Our efficient test system UTP 5069 offers exactly the right solution:By using CATR technology (Compact Antenna Test Range), 4D, imaging and other radar sensors with large far-field distances are calibrated with high precision in a small footprint. With the extremely low-reflection NOFFZ absorber chamber, the system is very well suited not only for validation, but also for EOL tests.
-
product
Low Impedance Voltage Tester
K-60
K-60 KNOPP VOLTAGE TESTER for AC and DC with polarity indicator. Double safety indication is by solenoid and by neon lamp. Knopp’s K-60 Low Impedance Voltage Tester (Cat. 14460) offers portability and ease of use with full protection. These exceptionally versatile and useful tools are backed by a reputation for quality in the design and manufacturing of electrical test equipment.
-
product
Catena 1910 HSIC Tester
Catena 1910
The MCCI Catena 1910 HSIC USB Tester enables testing of HSIC Host or HSIC Device products. It can be used to exercise your product by operating as an active host or active device, while simultaneously capturing USB traffic for analysis. For test and validation of a final system, Passive Capture mode lets you debug and verify communication between your HSIC Host and HSIC Device,
-
product
NI-9220, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module
785188-01
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module - The NI‑9220 performs simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. The module is capable of generating 3.2 MB/s of data at the maximum sampling rate. There are two connector options for the NI‑9220: a 36-position spring-terminal connector and a 37‑position D‑SUB connector.
-
product
Products for High-Frequency Measurement
This product range includes passive high-frequency test probes and accessories as well as touch-protected BNC plug connectors, insulated BNC panel-mount sockets, leads with RG58 or RG59 cable, adapters and converters. Our test probes are suitable for use in CAT III- and CAT IV environments (Measurement Categories), such as the analysis of house and building installations with mains analysis/mains monitoring devices. Our high-frequency accessories are designed with clearance and creepage distances in accordance with IEC/EN 61010-031.
-
product
Handheld Instruments
Measuring DC and AC voltages up to 1000 V.Alternating current and direct current with resolution up to 0.01 mA.Measuring continuity, resistance, diodestest, capacity, frequency.MIN / MAX recording.CAT III 1,000 V, Cat IV 600 V; IP54.Wireless remote display. Smartphone connection.Fluke Connect Mobile App for Android and iOS, compatible with over 20 different Fluke products.
-
product
Modular Matrices
Modular Matrices include two ranges: - The LDX+ range provides a cost effective modular solution for budget sensitive projects requiring fewer advance features at shorter Cat 6 cable lengths of up to 70m.- The MDX+ range incorporates the videowall processor technology which allows a number of output blades to be grouped together to form a multi display video mosaic or wall. This feature is available for the HDBT, DVI, 3G-SDI and fibre output cards.
-
product
Erbium Doped Amplifier
CATV
Amonics CATY Rackmount EDFA area made with high power pump laser and stability pump combiners, robust in high power boosting. The result are EDFAs that possess high output power, high gain with very low noise, and are ideal for CATV applications. The turnkey microprocessor controlled rackmount EDFAs manage alarms and status indicators. An integrated RS232 or Ethernet computer interface enables easy control, diagnostic functions and data acquisition.
-
product
Small Full Safety Insulated Crocodile Clip
126017/Colour
IEC 1010 Rating: 300 Volts CAT II Double/Reinforced Insulation 10Amps Standard Colours: Black, Red, Green, Blue, Yellow, White Features: Will accept all standard 4mm plugs.
-
product
MirrorLink Test System
Catena 2210
The Catena 2210 is a test tool with two USB Network Control Model ("NCM") devices. These devices create a bridge between two USB hosts. Validation testing is made possible by connecting a test control computer to the USB host being tested. Ethernet traffic from the test host is transferred through the Catena 2210 device to the control host, and vice versa.
-
product
Catalytic Ozone Destructs
CAT-O3 Series
Teledyne Advanced Pollution Instrumentation
The CAT-O3 series of ozone destructs safely decompose high concentrations of ozone gas to sub-ppm levels that are below recommended ozone safety limits. The catalytic method of decomposition uses a metal oxide catalyst to passively convert the ozone to oxygen.
-
product
Heat Deflection Tester
Apparatus is used to determine the Heat Deflection Temperature or the Vi cat Softening Point. All the specimens are charged with a constant load and immersed in a bath, where temperature is increased at a standard velocity. The attained heat resistance rate of plastic materials is a widely required parameter for product characterization, for quality control, as well as for evaluating their conformity to the previewed applications.
