Bus Translator
Bus Converters are used as an interface between separately powered components of a logic system.
See Also: Bus
-
Product
PXI Dual Bus 74-Chan 2A Fault Insertion Switch
40-190B-002
Fault Insertion Unit
The Dual Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI 8-Slot BRIC Matrix, 230x8, 1-Pole (5 sub-cards) Dual Bus
40-560B-121-230X8-M
Matrix Switch Module
The 40-560B-121-230x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays
-
Product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
-
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
Product
PXI 8 Slot BRIC 184x8 1-Pole Dual Analog Bus (4 sub-cards)
40-560A-121-184X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
LXI Trigger Bus Cable
ProDAQ 8036
-
The ProDAQ 8036 LXI trigger bus cable connects the ProDAQ 6100 LXI function card carrier or the 3030 PCI Express VXIbus slot-0 interface to any device equipped with LXI triggers. The robust, shielded cable and the die-cast connectors ensure a stable connection and prevent accidental disconnects.
-
Product
PXI 4-Slot BRIC Matrix, 230x8, 1-Pole (5 sub-cards) Dual Bus
40-560B-021-230X8-M
Matrix Switch Module
The 40-560B-021-230x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PCIe Smart Bus Extenders
PCIeEXT-16 - PCIe SMART EXTENDERS
-
PCIe smart extenders provide an excellent platform for testing and troubleshooting PCIe devices. Furaxa's line of PCIe smart extenders provide current sensing on each power rail as well as current overload indication facilitating rapid troubleshooting and testing.
-
Product
PXI 4-Slot BRIC Matrix, 184x8, 1-Pole (4 sub-cards) Dual Bus
40-560B-021-184X8-M
Matrix Switch Module
The 40-560B-021-184x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC Module, 2 Resource Distributor, 1 Bus Matrix Inputs
40-569B-121
Matrix Switch Module
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-121 is a 8 slot module fitted with 1 Bus Matrix Inputs card and 2 Resource Distributor cards.
-
Product
PXI 4 Slot BRIC Module, 1 Resource Distributor, 2 Bus Matrix Inputs
40-569B-012
Matrix Switch Module
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-012 is a 4 slot module fitted with 2 Bus Matrix Inputs cards and 1 Resource Distributor card.
-
Product
Bus Analyzer / Protocol Analyzer
EZ-TAP™ PRO RS-232
-
Stratus Engineering’s EZ-Tap Pro hardware module RS232 sniffer is a sophisticated protocol analyzer and bus analyzer hardware solution that overcomes latency and time-tagging problems associated with traditional dual COM port monitoring solutions.
-
Product
PXI 4 Slot BRIC Module, 2 Resource Distributor, 2 Bus Matrix Inputs
40-569B-022
Matrix Switch Module
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-022 is a 4 slot module fitted with 2 Bus Matrix Inputs cards and 2 Resource Distributor cards.
-
Product
20U (35") Insulated Bus Bar
BB-35-I
-
20U (35") insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
Product
Bus Analyzer / Exerciser
VME850
-
The VME850 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to 2eSST protocol. In addition to the VME bus, user defined signals on the P0 and P2 connectors are also analyzed and exercised with optional plug-in modules.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
SparkFun Voltage-Level Translator Breakout
TXB0104
-
This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing.
-
Product
ECU & Bus Interface Modules
ES500
-
ETAS makes the entire software and hardware range available from program development to the calibration of your ECUs. You can use the ETAS tools to address all ECUs that satisfy the ASAM standard. By using these standardized interfaces, our tools are not limited to the ECUs of any particular manufacturer.
-
Product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
-
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
Product
Power And Bus Protection Units
-
Silver Engineering Inc. offers several Bus Protection Units designed to protect the power input to a spacecraft or payload during integration and test activates. The BPU’s monitor for over/under voltage and over current and disconnects power in the event of a fault condition.
-
Product
VME Bus Analyzer / Exerciser
VME650
-
The VME650 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to MBLT protocol.
-
Product
Power System Recorder with CDR , PMU and IEC 61850 station bus protocol
TESLA 4000
-
ERLPhase Power Technologies Ltd
The new TESLA 4000 is an intelligent, state of the art, user-friendly multi-timeframe dynamic power system recorder with advanced Phasor Measurement Unit (PMU) and Continuous Disturbance Recording (CDR) capabilities. Wide area swing recording accomodates system performance analysis in minutes Meets NERC continuous disturbance recording standards with non-volatile on board flash memory No mechanical moving parts – flash drive eliminates most common mode of failure in recorders. Each flash drive holds 1000 records. IEEE C37.118-2005 SynchroPhasor Standard
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB119
-
*Designed for PICMG 1.3 SBC*Compatible with AX6145, AX61400, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slots, one PCIe x16 slot, and ten 32bit/33MHz PCI slots
-
Product
Full-Size PCI Express Mini Module With CAN Bus
AX92903
-
*USB to 1 channel CANBus port*Support CANOpen*51 x 30 mm
-
Product
PCIe Gen3 X16 Bus Expansion Via Dual X8 OCuLink
PCI125
-
The PCI125 is VadaTech’s 4th generation PCIe expansion module based on the PCI-SIG specification. The Module has a Retimer/Conditioner to improve signal integrity for enhancing system performance and reliability across long cables. It removes both random and deterministic jitter from the input signals eliminating inter-symbol interference and resets the output jitter budget. It supports the full 16 lanes.
-
Product
Automotive Audio Bus (A²B) Analyzer System
-
A simulation and analysis solution for automotive audio networks based on the emerging Automotive Audio Bus® standard. The A2B Analyzer System is designed specifically for development teams servicing automotive OEMs, Tier 1s, and audio connectivity equipment suppliers. The deterministic nature of the A2B technology makes it particularly well-suited for automotive audio devices (active speakers, microphones) and newer applications such as Active Noise Cancellation (ANC), In-car Communications, etc.
-
Product
44U (77") Insulated Bus Bar
BB-77-I
-
44U (77") insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A, Hardware Interlock
40-194A-001-HI
Fault Insertion Unit
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with hardware interlock and one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
6-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB210
-
*Designed for PICMG 1.3 SBC*Compatible with AX61222TP/AX61220TP chassis*Supports one PICMG 1.3 CPU card slot, two PCI slots, two PCIe x1 slots, and one PCIe x16 slot
-
Product
PXI 4-Slot BRIC Matrix, 138x8, 1-Pole (3 sub-cards) Dual Bus
40-560B-021-138X8-M
Matrix Switch Module
The 40-560B-021-138x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
