Interrupters
-
product
RTXCview System Trace and Profiling Tool
RTXCview
RTXCview is a system trace tool designed to work in tight integration with the RTXC Quadros RTOS family. This powerful visualization tool gives you deep visibility into system performance and behavior. Typical embedded system development tools such as debuggers can only provide a static view of your system, focusing on code-level details. RTXCview complements this view by providing a system-level view, showing how tasks and interrupts interact with the RTXC kernel.
-
product
192 Channel Isolated Digital Input / Interrupt Module
DP-cPCI-3780
DP-cPCI-3780 provides 192 channel digital input / interrupt with optical isolation. The 192 channel input is divided into 12 groups of 16 channels. The inputs are designed for a input voltage range from 5V to 28V.
-
product
IP-Parallel-IO
IP Compatible card with 48 programmable TTL IO or 24 - RS422 / RS485 compatible differential pairs. 5 mixed combinations available. Filtered or direct input. Programmable interrupt from each IO [TTL or differential]. 2 counter timers. Waveform generator.
-
product
PCI Bus Analog Output Board, 4 Isolated Outputs, 14 Bit
APCI-3501-4
4 analog output channels Optical isolation 500 V Settling time 30 µs typ. 14-bit resolution (13 bit for 0-10 V) Output voltage: ±10 V, 0-10 V (switchable through software) Output voltage after reset: 0 V Each output channel has its own ground line (without optical isolation from the others) Driver capacity: 5 mA/500 pF Short-circuit protection, EMI filters Noise neutralization of the PC supply Creeping distance: 3.2 mm acc. to DIN VDE 0411-100 Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary2 digital input channels, 24 V, isolated 2 digital output channels, 24 V, isolated Noise immunity Test level: ESD: 4 kV Fields: 10 V/m Burst: 4 kV Cond. radio interferences: 10 V
-
product
PCI Express, IEEE 488 GPIB Instrument Control Device for Linux
779779-01
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
product
32-Ch Isolated Digital I/O And 1-Ch Counter PCI Card
PCI-1750
16 isolated DI and 16 isolated DO channels.High voltage isolation on all isolated channels (2,500 VDC).High sink current on isolated output channels (200 mA/channel).Supports dry contact or 5 ~ 50 VDC isolated inputs.Interrupt handling capability.Timer/counter interrupt capability.
-
product
Multifunctional Meter
AEM-DR
Provide high accuracy measurement, display and remote communication of single phase & three phase parameters (V, A, P, Q, S, PF, Hz, Kwh). Multicircuit design and relay output modular expansion design decrease the overall cost and make the functionality more flexible. All monitored data is available via a RS485 serial , for the needs in energy management, alarming, and remote controlling. Embedded flash memory for Data-Logging can avoid any data missing once the communication is interrupted. Moreover, its ultra compact size DIN-rail mounting makes itself mountable in virtually any panel, enclosure or indoor Cabinet.
-
product
32-CH/64-CH Isolated Digital I/O PCI Express Card With Digital Filter
AX92351
The AX92351 is a 64-ch isolated digital I/O PCI Express card with 2,000VDC isolation protection. This high-density digital I/O card with high-speed PCI Express x1 bus is excellent for use in applications requiring digital control or monitoring, such as semiconductor machinery, PC-based industrial machinery, programmable I/O logic control, and process status monitoring. The AX92351 features 32 isolated digital input channels and 32 isolated digital output channels with isolation protection of 2,000V for industrial applications where high-voltage isolation is required. It is equipped with a board ID feature for easy identification of multiple cards in single system. There is a digital filter function to prevent input signals from carrying noise or a chattering. Each isolated input has a sink or source current which supports dry and wet contact for maximum application flexibility. The card has a wide range of input voltage from 10 to 30V to meet most industrial application needs. The AX92351 also provides two interrupt sources on digital input channels. Digital output has open controller and supports maximum 30VDC. The read-back function is another useful function that allows monitoring each output port.
-
product
Transformer Winding Resistance Meters
RMO TT Series
The Tap Changer Analyzer & Winding Ohmmeter of the RMO-TT series is designed for winding resistance measurement of inductive objects, and for a tap changer analysis. The RMO-TT series is based on the state of the art technology, using the most advanced switch mode technology available today. The RMO-TT instruments are accurate (0,1%), powerful (up to 100 A) and still portable. The Instruments generate a true DC ripple free current with automatically regulated measurement and discharging circuit. RMO-TT instruments can perform a simple, quick and reliable transformer on-load tap changer condition assessment. This series of instruments enable measurements of a winding resistance in every tap position, current ripple values (percentage of a current drop during a tap change) and transition times during the tap changes. Problems with a connection, contacts, and selector/diverter switch operation (tap change with interruption) can be detected with these measurements.
-
product
Acquisition Of 16 Displacement Transducers
APCI-3701-16
PCI interface to the 32-bit data bus Acquisition of 16 inductive displacement transducers (Half Bridge, LVDT) 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
product
Light-to-Digital Proximity Sensors
Renesas' light-to-digital proximity sensors offer low light sensitivity, superior proximity range performance, low power consumption, easy to use simple output algorithm, and an array of other features including intelligent interrupt, sleep modes and Time of Flight (ToF) signal processing.
-
product
C012 Communication Board
MS 1728/29
- Suitable for standard desktops- Four channel in single board- Up to 10 Mbits/sec operating speed- Low Cost solution- Standard INMOS link protocol- Communicates with transputers- Converts between serial link and parallel bus- Tristate bidirectional bus interface- Memory mapped registers- Interrupt capability- TTL compatibility
-
product
Optical Sensors
Vishay's proximity, reflective, transmissive, slotted interrupters, optical and ambient light sensors put the "smart" into smart devices. Advantages of Vishay sensors include best-in-class performance, in-house chip manufacturing and assembly including AEC-Q101 automotive grade product lines, and comprehensive range of package types for wide range of applications.
-
product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
product
PCI Express Digital I/O Card With Counters And IRQ
PCIe-DIO-24HC
This product is a x1 lane PCIe DIO board with basic DIO, Counter/Timers and interrupt generation capabilities. The card uses an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C is further broken into two 4-bit nybbles via software, configured as either inputs or outputs.
-
product
Shared Memory Network PXI Express Instrument
PXIe-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - 3U PXI Express Module - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
ARINC 429 Test And Simulation PXI Module
PXI-C429
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
32 Channel Analog Comparator Module
DP-VXI-5106
DP-VXI-5106, is a 32 Channel Analog Comparator Module with 32 channels of differential analog window comparators. Each channel is provided with a window comparator as well as a Level Comparator , software selectable on an independent channel basis. All the 32 channels have been grouped into four groups of 8 channels each. This allows the user to configure the comparator module based on the application to initiate alarm action to exactly meet application requirements. Each Comparator channel can be programmed to generate a VXI bus interrupt or can be masked through software. An Interrupt is generated on an individual channel basis or on a group basis. Front panel outputs of buffered TTL and a 2-CO relay contact is available for every group (4 outputs total each). Also, a common buffered TTL interrupt output and a common 2-CO relay contact is also available at the facia providing extensive flexibility in application engineering.This module is an ideal device for GO / NO-GO testing in Test Stand Automation where important signals must be continuously monitored for system shut down purposes and safety inter-lock implementation. The hardware implementation in the Comparator module provides high-speed throughput and reliable inter-lock implementation. The interrupt out signal can be further wired as trigger signals for pre and post trigger analysis of signal data for post acquisition detailing.Each channel provides a Window Comparator implementation and a Level Comparator implementation. The configuration is programmable through software and the alarm can be generated if the signal is within the window or outside the window. Similarly, a high and low limit can be set and a trigger is generated if the signal exceeds the high limit or drops below the low limit.
-
product
M-Module Carrier for VMEbus (6U)
i4000
The i4000 is a 6U form factor M-module carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating a mix of M-modules in a VMEbus system. Four M-module mounting sockets are provided by this carrier.The interrupt controller on the i4000 has an interrupt vector register for each M-module interface.
-
product
Current Transformer with Open Core
TCP
Lifasa - International Capacitors, SA
The TCP series is designed for installations in operation. It has a removable core that allows its connection without interrupting the power supply.
-
product
PCIe Digital I/O Board, 32 Optically Isolated I/O Channels, 24V
APCIE-1532
16 digital inputs, 24 V, isolated16 interruptible inputs16 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
product
PCI Multifunction I/O
626
6 versatile 24-bit counters for encoders/timers with interrupt generation Fail-safe Digital I/O E-stop Relay Battery backup of counters Four 14-bit D/A outputs, 20 Khz update rate Sixteen 16-bit differential A/D inputs, 15 kHz rate Watchdog timer may be used to reset PCI bus 48 bi-directional digital signals for solid state relay boards, 40 with edge detection and interrupts
-
product
IO60-DIO48 Module
IO60-DIO48
WINSYSTEMS’ IO60-DIO48 Module adds GPIO to embedded systems with IO60 expansion featuring 48 GPIO (General Purpose Input-Output) tolerant to 30 V DC. The SPI interface is implemented through the MACH XO2 SPI-slave EFB (Embedded Function Block) interface. Each bit of each port is implemented as a bi-directional tristate driver. Each bit of each port can also be configured and enabled to detect rising and/or falling edge events and generate a system interrupt.
-
product
NI-9265, 4-Channel C Series Current Output Module
779334-02
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
product
Terminal Power Meter
TPM-50A
ShinewayTech@ TPM-50A Terminal Power meter can test (1) Average power range: -40 dBm~+20 dBm；(3) Modulation bandwidth: 5MHz；(3) Continuous signal and burst signal test. Highly accurate power measurement CW and digital modulated signal (For example: GSM/EDGE, CDMA/EV-DO, WCDMA/HSDPA, WiMAX, and TD-SCDMA). It is very important to test that if the transmitter is at a specified level or not. For example, the tester needs to test the output power of base station. Because the lower output power produces the larger coverage area to cause call interruption.
-
product
PCI, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
783007-01
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
product
Shared Memory Network PCI Express Interface
PCIe-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodesNetwork interrupts supported - PCIe 2.0 (x4) CompliantSoftware Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
Industrial Operations
Schweitzer Engineering Laboratories, Inc.
Comprehensive power management systems optimize power delivery to minimize production interruptions and save money. SEL power management, process control, and automation products are designed for the conditions common in industrial power systems.
-
product
48 Channel Isolated Digital Input/Output Module
DP-VME-3078
DP-VME-3078 is a 48 Channel Isolated Digital Input Output Module. This module provides 48 input / interrupt channels and 48 digital output channels with isolation. The 48 channel inputs are divided into 12 groups, each group consisting of 4 channels and 1 common GND .The 48 output channels are divided into 6 groups, each group consisting of 8 channels and a common GND.
-
product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
