High Voltage
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500. AKA: HV
See Also: High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, HV
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 1m HV, Exit Away From Pin 1
A050DF4-C-HA100
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
16-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-8
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 32-Channel, 4-Pole
42-614D-017
The 40-614D-017 (PXI) and 42-614D-017 (PXIe) 1-bank, 32-channel, 4-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Portable PD Monitoring of Medium and High Voltage Power Equipment with UHF, AE, and HFCT
PDiagnosticM
Power Monitoring and Diagnostic Technology Ltd.
The PDiagnosticM is a portable system that utilizes UHF, AE, and HFCT sensor modules to monitor PD signals from Medium and High Voltage power equipment.The system is ideal for monitoring critical power assets to find and monitor intermittent PD signals and to analyze the developing PD trends. The PD type is determined by automatic pattern recognition and internal defects can be found at an early stage.The system provides advanced protection with alarm functions and our Deep Learning data analysis capabilities utilizing our proprietary Intelligent Cloud Diagnostic Technology.
-
product
Insulation Tester
1555
The Fluke 1555 insulation resistance tester offers digital insulation testing up to 10 kV, making it ideal for testing high voltage equipment including switchgear, motors, generators and cables.
-
product
1000A AC Clamp Meter
CM55
The CM55 is a pocket sized high performance AC Clamp meter measuring AC current, AC/DC voltage and resistance with continuity test. The compact rugged design enables accurate and reliable current measurement down to 10mA resolution without the need to break into the circuit.The CM55 has a CATIII 600V safety rating and is the ideal tool for residential and commercial electricians.
-
product
Sensor Conditioning Data Recorder
DTX-6017SSC/HV
The DTX-6017SSC/HV series of data acquisition systems provide wideband, low noise sensor signal conditioning with embedded filtering, digitization and data recording direct to 4GB of SDRAM locate on each DTX-6192 module. System level recording rates are no longer limited by chassis throughput, bus bandwidths or long term disk storage speeds. A comprehensive user GUI running on the embedded Windows OS can be used locally with the addition of a user keyboard, mouse and video terminal, or run remotely via the integrated Ethernet connection.
-
product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 2-Pole
40-321-121-HI
The 40-321-121-HI (PXI) and 42-321-121-HI (PXIe) are quad 5-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
High Voltage Insulation Tester
505
Simpson's Model 505 High Voltage Insulation Tester is capable of measuring insulation resistances from 10 kilohms to 1 teraohm with eight selectable test voltages up to 5000 V. As a safety feature, the insulation tester acts as an AC/DC voltmeter to measure the absence of voltage in networks up to 2000 V.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m, HV
40-972-037-0.5m-MU-HV
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Manual Ranging Digital Multimeter
HH3502
Double Injection Casing. High Accuracy (basic accuracy 0.5%). 3-1/2 digit Jumbo LCD display 2000 count with symbolic signs and back light. Manual Ranging High Voltage test up to 1000V DC and 750V AC. Higher Current test up to 20A AC/DC. Transistor test. Diode and Continuity check. Measure Resistance up to 20MΩ
-
product
9-Pin D-Type, Right Angled PCB, Female, HV
40-963-009-RF-HV
9-Pin Female Right Angled D-Type Connector, High Voltage - PCB Mount
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 2m HV, Exit Towards Pin 1
A050DM5-F-HA200
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
LXI Dual 75x4 2-Pole HV Matrix
60-311-002
The 60-311 is a 2-pole Matrix Module available with one, two or three separate 75x4 matrices housed in the same case. It is capable of cold switching 750VDC continuous with a carry current of 2A plus higher pulse conditions e.g. typically 1000VDC for 1s with low duty cycle or 6A for 200us with <1% Duty Cycle.
-
-
product
High Voltage DC Lab Power Supplies 300V-5000V Output for Research Labs / Capacitor Testing – 300, 600, 1000, 3000, 5000V
- 19” Rack Adaptable- Laboratory Bench Unit- Digital Output Metering- Constant Voltage Current Limit Type Character- Micro Switch Provided for Protection against Shock- 3U High (133 mm)- Power Saving Thyristor Preregulator Technique
-
product
Wide Range Ohmmeter
PAS-853B
- Wide Resistance Measurement Range from 0.01 ohm to 9.99x1012 ohms- Nominal Full Range Tolerance Averages <±5%- Fully Automatic Resistance Range, Test Voltage and Electrification Period Control- Automatic or Continuous Electrification ControlRugged High Performance 80 inches (200cm) Test Leads Included- Powered by one long lasting 9V Alkaline Battery- Large, Easy to Read LCD Display- Meets requirements of ESD Association Standards for material and audit resistance measurement requirements- Certificate of Calibration Traceable to NIST included
-
product
PXI 20Amp 28Volt 2xSPST Automotive Relay
40-180-011
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
product
High Speed Phase Inverter - Buffer
WMA-IB-HS
The WMA-IB-HS can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision, high speed and low noise. Because of its high bandwidth, the WMA-IB-HS model is ideal for the Falco Systems WMA-100 or WMA-300 amplifiers. It can also be used with all other Falco Systems HV amplifiers, or even with high voltage amplifiers of another brand.
-
product
LXI Single 75x4 2-Pole HV Matrix
60-311-001
The 60-311 is a 2-pole Matrix Module available with one, two or three separate 75x4 matrices housed in the same case. It is capable of cold switching 750VDC continuous with a carry current of 2A plus higher pulse conditions e.g. typically 1000VDC for 1s with low duty cycle or 6A for 200us with <1% Duty Cycle.
-
product
PXI High Resolution Waveform Digitizer Family
PXD730x
The PXD730x High Resolution Waveform Digitizer family features up to two 100MS/s simultaneously sampled input channels with 16Bit resolution, input voltages up to ±60V and a bandwidth up to 50MHz. Every digitizer channel has its own 2MB memory which allows up to 1 million samples. Data can be acquired before and after the trigger event with a programmable sample counter, that controls the number of data points.
-
product
PXI-2585, 10‐Channel, 12 A, 1-Wire PXI Multiplexer Switch Module
778572-85
10‐Channel, 12 A, 1-Wire PXI Multiplexer Switch Module —The PXI‑2585 is a high‐power PXI multiplexer switch module that is ideal for switching power signals and loads in control applications and battery, power supply, and automotive testing. It is configured as a 10x1 multiplexer with both low contact resistance and high isolation voltage. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Digital Arrester Clamp Tester
ALCL-40L
MULTI MEASURING INSTRUMENTS Co., Ltd.
Lightning arresters are designed to protect a power distribution system by shunting to ground the high voltage surges caused by lightning. ALCL-40L measures to warn that an arrester is damaged or deteriorated and should not be energized.
-
product
Insulation Testers
Shenzhen Everbest Machinery Industry Co.,Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance.
-
product
Digital Panel Meter
VAM
Chuan Sheng Electronics Co., Ltd.
VAM Voltage & Current Meter has been designed with high accuracy dual channels(isolated) measurement, dual display and communication of 0~600V and 0~10A for DC/AC/TMRS. In compact size(48 x 96mm)● Build in mathematic function such as Addition / Subtraction / Multiplication / Division / high or low selector in 2 channels input to meet various testing equipment inquiry.They are also build in 4 Relay outputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.
-
product
HV AC Hipot
The HV AC Hipot package is a hardware and software upgrade available for select Eclypse Analyzers. This package adds a High Voltage AC stimulus source CCA to the analyzer chassis and the HV AC Stimulus utility provides the software drives for ELITE to integrate AC Hipot into test programs.
-
product
USB Programmable SPDT and SP4T Solid State RF and Microwave Switches
LSW Series
The Lab Brick LSW Series RF and Microwave Switch product family offers reliable, high isolation and low cost solid state switch products in both single pole double throw and single pole four throw configurations. These units require connection to a USB port for control and power. No additional DC supply voltage is required. Lab Brick RF and Microwave Switches are easily controlled and programmed directly from the included GUI and through the external control inputs. Lab Brick Switch API DLL and LabVIEW compatible drivers are also available for custom programming applications.
-
product
NI-9213, cDAQ-9171, and cRIO-9940 USB Temperature Measurement Bundle
865682-01
NI-9213, cDAQ-9171, and cRIO-9940 USB Temperature Measurement Bundle - The USB Temperature Measurement Bundle with NI-9213, cDAQ-9171, and cRIO-9940 includes the NI-9213 C Series Temperature Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the cRIO-9940 Backshell for strain relief and operator protection from high-voltage signals. The included NI-9213 provides noise immunity, a high common-mode voltage range, NIST-traceable calibration, differ...show more -
product
EEPROM
Renesas EEPROM realizes high speed, low power consumption and a high level of reliability by employing advanced MONOS memory technology, CMOS process and low voltage circuitry technology.
-
product
Test Leads
AL-34WB
Standard Electric Works Co., Ltd
● Wire length: 1.2m approx. Silicone insulated wire (1000mm) with wire connected to straight input plugs (130mm PVC wire), and wire for clamp (100mm PVC wire). ● Outside diameter of silicone insulated wire: 5mm Outside diameter of PVC wire: 3.5mm● Input plug color: Red•Green•Black•Blue ● Current rating: 5A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
