Showing results: 2716 - 2730 of 5280 items found.
-
Extech 480403 -
Extech Instruments Corporation
The 480403 Phase Sequence and Motor Rotation Tester has a 40 to 600-Volt rated range for testing phase orientation of 3-phase power sources over a 2 to 400Hz frequency range. LEDs indicate phase orientation (clockwise or counter-clockwise) and whether each of the phases is live. In addition, it indicates rotation direction of the motor to ensure that it doesn't get damaged from incorrect wiring. Meter comes complete with cable and three large color coded alligator clips, pouch case, and 9V battery.
-
Imapact 7BT -
Lorlin Test Systems
The 7BT Benchtop Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The 7BT automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability. The system tests most all discrete semiconductors with reliable, accurate, and repeatable results and uses a Windows 10 64-BIT Operating Systems and a USB 2.0 Interface.
-
HopeTech
program-controlled safety tester includes CHT9910 / 9912/9922; it has AC / DC withstand voltage test and insulation resistance test function; it has 6 groups of test modes and can realize programmable test.AC / DC voltage output 10V ~ 5KV / 6KV, insulation resistance test range: 100KΩ ~ 99GΩ, meanwhile, it has arc detection and over power detection functions. Optional RS485 interface, you can easily experiment with instrument networking through MODBUS communication protocol.
-
CT8002 -
General Technologies Corp.
No Ground or clip required. No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance Electronic circuitry. Safety V-groove needle accessory for piercing and carrying. Negligible current draw ( 20 micro-amps) is 10,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 3 and 28 Volt DC in battery powered systems.
-
C2G, Lastar, Inc.
For anything compture repair and workstation installation tool, you've come to the right place. C2G carries a variety of cable tools and testers for network, coaxial, electrical, F-type, PC, telephone, and fiber cables. Our crimp tools are also available for RCA, BNC, F-type, RJ45, RJ11, RJ12, and flat ribbon connectors. C2G cable cutting tools can be used to cut a range of wiring types, from RG6 and RG59 coax, speaker wire, UTP network cable, flat ribbon, and more.
-
Explorer® 2 -
Klein Tools, Inc.
Tests coaxial cable and maps up to 4 locations. Tests coaxial cable and maps up to 4 locations. Simple push button operation • Easy-to-read LED panel indicates PASS, OPEN or SHORT conditions, simplifying cable identification • Color-coded push-on remotes allow for up to four cables to be tested and mapped at the same time• 4 color-coded test remotes and included F-adapter conveniently snap into the remote holder for storage; the remote holder clips onto the tester.
-
DRK120 -
Shandong Drick Instruments Co., Ltd.
DRK120 aluminum film thickness tester is new instruments as the development of new packaging material. It is used to test aluminum coating in the barrier film, which is around 35NM thickness. This aluminum coating improves the barrier property a lot, because common gas and aromatic gas couldn’t dissolve in metal. The aluminum coating could protect packing material and avoid light. So thickness test and control of aluminum film is very important, the thickness of aluminum will affect the barrier property of film a lot.
-
6900 -
KANOMAX USA, Inc.
Kanomax has developed the most advanced Duct Air Leakage Tester (DALT) for commercial duct systems. It’s designed to be simple to use, accurate, and extremely convenient. The instrument provides step-by-step duct leakage test configuration and automated leakage testing based on the SMACNA HVAC Air Duct Leakage Test Manual, and is accurate to ±2.5% of reading. Though built tough with an on-board, powerful motor, the DALT 6900 is very easy to transport on its pneumatic tires and leaves little to no footprint on the job site.
-
PK-3456 Spy Splitpair -
Pansco, Ltd
Easily & accurately tests twisted pair cables for proper continuity and correct signal pair. A split pair can cause a crosstalk problem and suppress the communication speed. The SpySplitpair also includes a Full test, One-ended testing, Debug mode for checking the specific pair fault, and a Tone mode for tracing cable as well as a Voltage warning indicator to protect the tester. Hub blink/Net Tone mode (PK-3456E only), display of the Ethernet port to which the test cable is connected, and identify unknown RJ45 outlet for active Ethernet.
-
TIME®3231 -
Beijing TIME High Technology Ltd.
TIME® 323X series is advanced high-end surface roughness measuring instruments with wide testing range (±400µm) and high accuracy (tolerance±5%, repeatability 3%). Meanwhile, TIME® 323X surface roughness tester features with skidless/skid measurement, which means it can reach smaller and harder to reach parts than other conventional tools. Up to 55 paramenters for roughness, waviness and primary profile are supported. Apart from those features mentioned above, TIME®3231 is loaded with 90° measurement function.
-
FLIR VT8-Series -
Teledyne FLIR
The FLIR VT8-Series are high-quality voltage, continuity, and current testers. They feature an optimized, open-jaw design that can fit into tight spaces and reliably measure large-diameter cables. The VT8-600 carries a CAT III-600 V/CAT IV-300 V safety rating and a 100 A/600 V measuring range, while the VT8-1000 carries a CAT III-1000 V/CAT IV-600 V safety rating and a 200 A/1000 V measuring range. Extensive measurement features make the VT8-Series versatile tools – just one meter can get the job done.
-
DWTT -
Qualitest International Inc.
Since the introduction of the Drop Weight Tear Tester - DWTT, materials have moved on. In particular, demands for high operating pressures of line-pipes and larger diameters have driven the development of higher strength steels. Forty years ago the work that led to the drop weight tear test was done on X52 steel (360MPa yield strength). Improvements in thermo-mechanical processing has yielded improvements of approximately 10,000psi per decade, to the point where the state of the art is now X100 steels, and the use of X120 steels is being considered.
-
1825 LP -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures the voltage drop as if 16A was flowing between Line and Neutral.● Displays voltage without current (V at 0A).● Display voltage as if 16A flowing between Line and Neutral (V at 16A).● Loop test for L-E● PSC between L-N.● Single one smart push button operation; ON, Scroll through results and menus.● Checks wiring integrity (LEDs).● Auto off/auto ranging (software range).● Combined prospective short circuit current, loop and load tester.● Display can be customized for large orders.
-
BAE Systems Inc.
The nation’s Air Force, Army, Navy, Marine Corps, and key government agencies all depend on countermeasure dispensing systems – including the AN/ALE-47 and others – aboard their aircraft for self-protection against missile attacks and other airborne munitions. Especially when operating in contested areas, a properly-functioning countermeasure dispensing system can make all the difference to the success of a mission. That’s ample reason for aviation maintenance and flight prep crews to prefer the unmatched reliability of BAE Systems Rokar Countermeasure Dispenser Testers (CDT) for keeping their countermeasure dispensing systems performing effectively and safely.
-
LEDLS-60/LEDLS-12 -
Lisun Electronics Inc.
• The tester includes A Group Measuring Module and B Group Measuring Module. The A Group measuring module can test 6pcs LED Driver AC Parameters. The B Group measuring module can test 6pcs LED Driver AC, DC and AC/DC Parameters. • There are 12 windows to display the input and output parameters, it is good for comparing and analyses. • Quick test for all of the parameters in 0.1 seconds. • It can set up the testing parameters PASS/FAIL range, it will have Noise/Light warning if it is Fail. We also supply handle port (Extra cost) • Software communicate with PC (Extra cost)
