Voltage Regulators
-
product
Bench Power Supply, DC, Single, Adjustable, 1 Output, 1 V, 36 V, 0 A, 3 A
72-8345A
Switch Mode Laboratory DC Power Supplies Precision adjustable supply provides adjustable 1~36VDC output with adjustable current limiting from 0~3A. It is ideal for test, measurement and service applications where tight voltage and current regulation are critical. Highly efficient switch mode design delivers outstanding performance from an extremely compact footprint. Unique separate output ON/OFF control allows voltage and current setting, with the supply output turned off. Part of a Complete Series, this slim supply occupies little bench space while providing very high precision and 90W of continuous output.
-
product
Miniature Fluxgate Magnetometer
WFG-120
The Model WFG-120 System is a complete 3 axis fluxgate magnetometer packaged in a rectangular/parallelpiped package of dimensions 0.75\" x 0.75\" x 2.75\". The package corners are rounded to enable the unit to fit inside a 1.0\" diameter cylinder. The system operates from one of two optional input voltages: regulated ±5 VDC or unregulated ±7 to ±12VDC and consumes a total power of 200 mW.
-
product
Low Voltage Switching Regulators
Renesas' comprehensive portfolio of low voltage, synchronous buck integrated FET switching regulators offer a compact solution size with outstanding performance.
-
product
AUTOMATED SUB-MM POWER SUPPLY/SWEEPER
IPPS 2-6/60
Power supply/sweeper model IPPS 2-6/60 specially designed by Insight Product Company to operate sub-mm wave BWO at frequencies up to 1500 Ghz. IPPS 2-6/60 produces highly stable regulated voltages for slow wave structure (anode) and filament/heater. This power supply is designed to simplify the operation with BWO, to protect BWO against distraction during start/stop routines, to allow fast frequency sweeping in the entire band, and also to allow BWO to be used within a frequency stabilization system.
-
product
AC Hipot Tester /DC Hipot Tester
YD-Series
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
YD series HIPOT tester is applied to test the insulation ability of electric power equipments and insulation materials at power frequency high voltage. The insulation test result of the tester is go or not go. Also the YD series HIPOT tester is a universal power source in HV test. The maximum output voltage and capacity could be customized according the requirements of custom.The tester is consists of single HV transformer and main control box. There are two kinds of HV transformer according to the insulation materials of the HV transformer.They are dry HV transformer and oil HV transformer. For the dry HV transformer the insulation material is epoxy resin.For oil HV transformer the insulation material is insulation oil. The dry HV transformer has a smaller size and less weight than oil HV transformer. But the maximum output voltage is less than 100kv for dry HV transformer. The functions of the main control box are voltage output regulation, protection in emergency and voltage/current value indication
-
product
Semiconductor Testing
Teradyne’s semiconductor test portfolio is transforming the way you test chipsets for automotive, industrial, communications, consumer, smartphones, and computer and electronic game applications. Semiconductor devices span a broad range of functionality, from very simple low-cost devices such as appliance microcontrollers, operational amplifiers or voltage regulators to complex digital signal processors and microprocessors as well as memory devices.
-
product
Power Discrete Tester
Mostrak-2
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
product
High Voltage SMU 2500 V
AXV7607
Generate extremely short, fully regulated voltage pulses of up to 2500 V. Measure leakage currents up to the pA range.
-
product
High Voltage SMU
Source and Measurement Units (SMUs) are devices that generate voltages or currents and can measure them simultaneously using the integrated measuring units (VMU, CMU).High-voltage SMUs work as a regulated voltage source and are able to generate very high output voltages.
-
product
Arduino CAN Shield
IFB-10003-ANP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
PXI Dual Programmable -10V Power Supply
41-736-001
A single slot power supply module providing two programmable negative output voltages. It provides high quality regulated voltages from a linear regulator to ensure low levels of output noise.
-
product
Analog Power Supply
Type NPS-2412
National RF's Type NPS-2412 analog power supply was designed to be used in communication equipment where radiated switching inverter noise from conventional “switching type” supplies is not acceptable. The power supply consists of a standard rectified transformer output driving a pair of voltage regulators and filtering networks. The 2412 offers an adjustable voltage output between 2 and 24 volts as well as a fixed voltage output of 12 volts. A maximum of 20 Watts of DC power can be supplied from the unit. As the voltage regulators dissipate power in the regulation process, the power to the load is derated accordingly, dependent on the set voltage to the load. The adjustable regulator is a standard LM-317T integrated circuit device. The fixed regulator is a standard LM 7812 device. Upon customer request, the LM 7812 device may be changed to any voltage rating within the the LM-78xx series of regulators. Contact National RF for this modification if desired.
-
product
PXI Dual Programmable +10V Power Supply
41-735-001
A single slot power supply module providing two programmable positive output voltages. The module provides high quality regulated voltages from a linear regulator to ensure low levels of output noise.
-
product
Bi-Directional Amplifiers
Fairview’s bi-directional amplifier models are designed for use in both commercial and military applications and will support any signal type and modulation format such as 3G and 4G telecom, WLAN, OFDM, DVB and CW/AM/FM. Fairview’s bi-directional amplifiers offer high power density, efficiency and linearity in small lightweight environmentally sealed packages with SMA connectors. These units also feature a quick-connect circular locking connector for DC and control functions and each design uses a single voltage supply with voltage regulation.
-
product
Powertrain ICs for ICE/HEV/EV
ST's powertrain ICs cover a variety of functions including voltage regulators, sensor interfaces, and load or motor drivers, which are the building blocks of typical Engine Control Units (ECU) found in a vehicle's main applications (engine management systems, transmission control systems, alternator regulators, etc.).
-
product
PicoBuck LED Driver
The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8860 part.
-
product
Phase Locked Dielectric Resonator Oscillators (PLDRO)
Corech’s PLDRO series is available in 10MHz/ 50MHz/ 80MHz/ 100MHz/ 120MHz/ 160MHz external reference, internal / external reference, internal voltage regulator and high output power. They are suitable for high-reliability and environmentally stressful applications including communication systems, test and measurement equipment, radar systems and instrumentation etc.
-
product
Power/Voltage Rail Probe. 4 GHz Bandwidth, 1.2x Attenuation, +/-30V Offset, +/-800mV
RP4030
The Teledyne LeCroy RP4030 Power Rail Probe meets the specific requirements of those who need to acquire a low-voltage DC signal as part of a:-Comprehensive power integrity, digital power management IC (PMIC), voltage regulator module (VMR), point-of-load (POL) switching regulator, or low-dropout regulator testing- Complete embedded power management system that includes PMICs, VRMs, POLs, and LDOsThe RP4030 will faithfully acquire a low-impedance, low-voltage DC power/voltage rail signal without unduly loading the device under test (DUT), while providing high offset to allow DC power/voltage rail signal display on an oscilloscope with high gain.
-
product
SparkFun Breadboard Power Supply Stick, 5V/3.3V
13032
This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.
-
product
Non-Contact Type Magneto-Electric Rotation Detector
MP-9820
MP-9820 is a magneto-electric-rotation detector using an internal hall element, a permanent magnet, DC amplifier, and voltage regulator in its compact body. Using MP-9820 in combination with detection gear enables deriving stable rectangular waveform from ultra low speed all the way through high speed. (1 Hz to 100 kHz)MP-9820 finds wide range of applications and rotational measurement objects by using with TM-3100 series tachometer and FV-1500 FV converter.
-
product
Power Supply PowerLab 305d-ii
PowerLab triple Series power supplies are reliable and accurate laboratory equipment with two outputs with adjustable and stabilized DC voltage and regulated (limited) power consumption and additional output has-voltage. Adjustable outputs can work independently, in series (max output voltage 120V DC for model 605-II) or parallel (max current of 10A for models 305-II and 605-II). Power can be used in the design of electronic products, scientific works, laboratories, production lines and in teaching.
-
product
Analog Sequencers
Analog sequencers from Analog Devices integrate accurate comparators with the control functionality of power-on and power-down sequencing for voltage regulator banks. The comparators monitor the regulator voltage outputs and trigger the turn on of next rail in the system after a preconfigured time delay. Some members of this portfolio can be cascaded together, which provides scalable solutions to expand functionality across multiple devices. Our analog sequencers provide an easy to use solution for power sequencing challenges in cellular infrastructure, telecommunication, data communication, and data center applications.
-
product
Test Bench
BERTA
OPAL-RT’s BERTA test bench is a safe, reliable and portable test bench for speed governors, turbines, voltage regulators (AVR) and power system stabilizers (PSS). Equipped with a high-performance real-time simulator programmed with world-renowned RT-LAB software, the BERTA Test bench enables users to easily and comprehensively test real generating units in the power plant, synchronized and transmitting power to the main grid and/or on real controllers connected to a virtual generating unit in laboratory.
-
product
SparkFun Breadboard Power Supply Stick
3.3V/1.8V
This is a very simple board that takes a 4-9V input voltage and outputs a selectable 1.8V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.
-
product
AC Voltage Monitors
NAI's AC- and DC-powered AC voltage monitors are used to monitor and measure voltage characteristics of single- and three-phase power lines. Field-adjustable AC voltage monitors are also available. These monitors are specifically designed for rugged defense and industrial applications.
-
product
NI-9202, ±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module
784400-01
±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module - The NI-9202 has excellent flexibility to meet the needs of your applications. The module has 16 simultaneous sampling, differential input channels to create large, distributed systems in a rugged form factor. It also has configurable filters to eliminate noise in your system while maintaining low-latency to be used in control systems.
-
product
NI-9269, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781098-01
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-02
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
product
NI-9239 , ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
780181-01
±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the NI‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range.
-
product
NI-9221, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779373-01
±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the NI‑9221: a 36‑position spring‑terminal connector and a 37-position D‑SUB connector.





























