Voltage Regulators
-
product
Regulators
The voltage regulators made by Ducati Energia are combined with permanent magnets alternators in order to manage both the battery charging and the direct supply of AC loads (lights, cooling fan, etc).
-
product
Dielectric Resonator Oscillators
Dielectric resonator oscillators (DRO) are free running oscillators that utilize state-of-the-art planar circuits, three-terminal devices and dielectric resonator technology to generate high-quality microwave signals with excellent frequency stability. In addition, these oscillators are equipped with an internal voltage regulator that further improves the frequency stability by isolating the external bias pushing and modulation. In general, these oscillators are fixed. However, a small mechanical or electrical tuning range can be achieved by use of a self-locking screw or an integrated Varactor diode. The standard offering covers the frequency range of 2 to 40 GHz. While standard models are equipped with female SMA and K connectors at the RF port, other RF interface options are also available.
-
product
GPIB Serial Interface
Model 4804B
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
product
Transformer Monitoring And AVR
Power transformer is a basic equipment for the Transmission and Distribution Network and requires the application of powerful Monitoring and Control Systems. RTU Dt set is developed and intended for medium and large oil immersed Power Transformers with On-load Tap Changers (OLTC). The set provides safe, reliable, easy to use and cost effective power transformer condition monitoring and Automatic Voltage Regulation (AVR).
-
product
AUTOMATED POWER SUPPLIES/SWEEPERS FOR BWO
nsight Product Company offer Automated Power Supplies/Sweepers specially designed to control mm- and sub-mm wave BWO sources. Those power supplies provides:*highly stable regulated voltages for slow wave structure (anode), filament/heater and control electrodes;*special design to simplify operation with BWO or WRO tubes;*special design to protect tubes during Start/Stop;*unique possibility for fast frequency sweep within entire frequency band;*possibility to use tubes within a PLL frequency stabilization system;*digital control and digital indication of output frequency;*built-in IEEE-488 interface;*multiple possibilities to control output frequency
-
product
Soil Moisture Sensor
Modbus RS485
This is a contact-less capacitive soil moisture sensor, a continuation of my I2C soil moisture sensor. This particular version of the sensor is suited for more professional installations where long cable runs is a requirement. It adds a local voltage regulator to mitigate the voltage drop and RS485 transceiver to accommodate long wires, also reverse polarity and an additional ESD protection level is added.
-
product
Arduino CAN Shield
IFB-10003-INP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
AC Source
5310(0~500Vrms/1KVA)
Voltage output has totally six ranges,maximum up to 500V,convenient for 300V above the voltage regulation test
-
product
Smart GPIB Serial Interface Board
Model 4806
* Provides GPIB-to-serial and serial-to-serial data paths for serial devices with RS-232 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message. • On board voltage regulator for operation from 5 to 15 Vdc power. • Rear panel mounting eliminates cables.
-
product
Stabilized Power Supplies
Stabilized power supplies are essential devices for providing stable DC voltage to electronic circuits and equipment.They offer features such as precise voltage and current regulation, short-circuit and overload protection, and advanced control functionality.Stabilised power supplies of our own design and manufacture can be built with output power up to 40kW even in models with 2- or 4-quadrant bipolar outputs.
-
product
Magneto-Electric Rotation Detector
MP-981/AP-981
The MP-981 is a magneto-type detector using a hall element which is suitable for revolution (r/min) measurement from low speed to high speed.Magneto-type detectors use an internal hall element, a permanent magnet, DC amplifier, and voltage regulator and respond to flux, so that a rectangular wave form is derivable from much lower speed all the way though high speed.In addition, a signal indicator is provided in spite of the detector's compact design, making verification of operation and mounting position possible.Meanwhile, the AP-981 is the water and acid proof type, which conforms to Class ' of JIS C0920.
-
product
Arduino CAN Shield
IFB-10003-IWP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
Micro-Size Power Supplies
Advanced Energy’s micro-size, high voltage DC-to-DC converters offer a variety features — arc limits, tight line and load regulation, voltage monitoring, and more. Get the right solution in the perfect size.
-
product
6000 Series ATE(AC Source)
Voltage output has totally six ranges,maximum up to 500V,convenient for 300V above the voltage regulation test
-
product
SMD Testers
Is a miniaturized and integrated utility model measuring instrument, which can automatically identify components such as resistance, capacitance, diode, etc., with LED, voltage regulator, DCV, on-off and battery power measurement functions. SMD resistance, capacitance, diode (RCD) parameter measurement, is a good helper for electronics factories and electronics maintenance.
-
product
RF Power Amplifiers
RF power amplifier category from Pasternack have components packaged in a hermetically-sealed metal enclosures and exhibit outstanding performance in high gain, gain flatness, high linearity and wide dynamic range. RF power amplifiers have excellent performance by using a hybrid microwave integrated circuit design and advanced GaAs pHEMT components. These SMA power amplifier modules are unconditionally stable and include built-in voltage regulation, bias sequencing, and reverse bias protection for added reliability.RF power amplifier over-voltage protection is installed externally for easy repair. These high reliability radio frequency power amps are fully matched internally for 50 Ohm input and output. This 50 Ohm power amplifier matching helps eliminates the need for any additional sensitive external RF tuning components.Our power amps are ideally suited for high linearity applications. These radio frequency power amplifiers offer small signal gain over a temperature range. The Pasternack RF power amplifiers have excellent gain flatness ranges and the IP3 output performance.Most all Pasternack RF power amplifiers are EAR99
-
product
Low Voltage Regulation
The low voltage regulation system LVRSys represents a cost effective alternative for grid expansion. The economic use is recommended in all low voltage grids where short-circuit power is sufficient, but have voltage maintenance problems.
-
product
NIM and CAMAC Power Supply
UEP 15
The UEP 15 is a plug in power supply for use in UEN 04 bin or for powering every non-powered extant NIM bin. The UEP 15 features all 6 voltages, stabilized by adjustable monolithic voltage regulators. Outputs are ported using a rear mounted NIM connector with a standard NIM pin out.
-
product
Voltage Regulator Testing Units
With the goal of providing the industry with the best products ahead of the curve, we continue to develop a complimentary line of Voltage Regulator Testing Units for laboratory and production testing.
-
product
Miniature Fluxgate Magnetometer
WFG-110
The Model WFG-120 System is a complete 3 axis fluxgate magnetometer packaged in a rectangular/parallelpiped package of dimensions 0.75\" x 0.75\" x 2.75\". The package corners are rounded to enable the unit to fit inside a 1.0\" diameter cylinder. The system operates from one of two optional input voltages: regulated ±5 VDC or unregulated ±7 to ±12VDC and consumes a total power of 200 mW.
-
product
Filament Transformers
Osborne designs and produces high impedance and unregulated Filament Transformers. An unregulated filament transformer supplies a specified voltage and current to the filament of an electron vacuum tube. High impedance filament transformers are designed around a tungsten tube filament. Osborne often works with our clients to increase the life-span of their vacuum tubes through the use of a regulated voltage supply.
-
product
Smart GPIB Serial Interface Board
Model 4816
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
product
SparkFun FTDI Basic Breakout
Beefy 3
This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. Built upon the same foundation as our 3.3V SparkFun FTDI Basic Breakout, the Beefy 3 is equipped with an AP2112K voltage regulator making this FTDI basic breakout board capable of handling a current load of up to 600 mA! With the addition of a more "Beefy" voltage regulator your will now be able to power a 3.3V project directly from the FTDI. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards.
-
product
Rad-Hard Power Management
ST offers a comprehensive range of QML-V rad-hard power management solutions for space applications including linear voltage regulators (low-dropout regulators), point of loads (switching DC/DC converters), PWM controllers, gate drivers, and an industry-unique integrated current limiter.
-
product
Alternator Tester
ALTALYZER Tester
The Altalyzer tester is used to check the correct operation of alternators equipped with electronically controlled voltage regulators. In alternators of this type, the charging voltage is not constant, but varies depending on external factors such as: engine revolutions, number of current receivers, etc. The voltage at a given moment is determined by the motor controller by sending the appropriate information to the alternator.
-
product
ST10 16-bit Automotive MCUs
ST's ST10 microcontroller family offers a wide range of devices for use in automotive applications. The family integrates scalable single-voltage embedded Flash, from 128 to 832 Kbytes. Processed in 0.18 µm CMOS technology, it offers full 5 V capability and an internal on-chip voltage regulator.
-
product
Automatic Voltage Regulating Relay
NMC introduces low cost microcontroller based basic automatic voltage regulating relay, type : h-101.





























