-
product
Custom Industrial IoT Product Design
Our custom-designed access points, radio and sensor communication modules, and other Industrial IoT devices are purpose-built to deliver high performance, reliable connectivity under demanding conditions. We focus on applying the latest wireless technologies, including evolving cellular, WiFi, and Bluetooth/BLE standards, for specific applications across manufacturing, intelligent transportation, mining, utilities, oil and gas, and other industrial markets. Through the entire design and developm...show more -
product
16 Channel Multiplexer (2/4-wire) Module for 34970A/34972A
34902A
The Keysight 34902A module for the 34970A/34972A Data Acquisition/Switch Unit employs reed relays to achieve scan rates up to 250 channels-per-second. Use this module for high-throughput automated test applications as well as high-speed data logging and monitoring tasks.
-
product
Delays And Gates
Delays, Gate and Delay Generators, Logic Modules, and Linear Gates are used in many research or teaching experiments and in non-research applications such as actively shielded spectroscopy systems. Delay modules allow the alignment in time of signals from different paths, so that a logical decision can be made within a logic module which will often result in an electronic go/no-go decision as to whether a particular detector analog output will be processed within an associated multichannel analyzer.
-
product
Mixed Protocol Modules
The ANET-MxAy offers mixed protocol support, combining MIL-STD-1553 and ARINC429 data bus test and simulation capabilities in one ANET device.
-
product
OEM 1-Channel Fiber Optic Signal Conditioner PCB Module
FOTEMP1-OEM-MNT
The FOTEMP1-OEM-MNT is a small form factor PCB interface module designed for low cost insertion of high precision GaAs-based fiber optic temperature sensor technology into OEM applications where common electrical temperature sensors and thermocouples cannot be used. The OEM interface product is compatible with all TS series fiber optic temperature probes. The sensors are entirely non-metallic and electrically passive, providing immunity to EMI, RFI, MR, microwaves and radiation is required.
-
product
High Power Modules
VPC offers a wide array of modules with a variety of connection options that are configurable for virtually any interconnect requirement.
-
product
PXI/PXIe High Density 2A Multiplexer, 8-Bank, 16-Channel, 1-Pole
42-614D-003
The 40-614D-003 (PXI) and 42-614D-003 (PXIe) 8-bank, 16-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI 12-Slot BRIC Matrix, 572x4 2-Pole (13 sub-cards)
40-562B-322-572X4
The 40-562B-322-572X4 is a high density BRIC12 matrix module with a size of 572x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Network Interface Card
NIC10GBT
The NIC10GBT is a dual port 10GBase-T XMC module that brings 10GbE expandability to new and existing embedded systems with available XMC slots.
-
product
PXIe Precision AWG: 4 Channels, 400 MHz
M5301A
The M5301A is a single-slot PXIe module with four baseband AWG outputs, clock input and output, and four triggers. It provides high performance with easy-to-use programming libraries, real-time sequencing technology, and FPGA programming.
-
product
PXI-6238, 8 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sourcing DO, Bank-Isolated, PXI Hybrid, Multifunction I/O
779624-01
8 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sourcing DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6238 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, sourcing digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurement...show more -
product
Isolation Amplifier
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics...show more -
product
25 Pin D-Type Cables - Connector to Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 25-pin D-type connector.
-
product
cRIO-9042, 1.60 GHz Quad-Core CPU, 4 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controlle
785622-01
1.60 GHz Quad-Core CPU, 4 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller - The cRIO-9042 is a rugged, high-performance, customizable embedded controller that offers Intel Atom quad-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and determinis...show more -
product
PXI Hardware
PXI is now the primary format for ATE Self Integrators. Terotest offer a complete range of PXI equipment that is designed to work together and has full software support for all its PXI modules and drivers.
-
product
Built-in Measuring Instruments
PeakTech Prüf- und Messtechnik GmbH
Practical built-in module as voltmeter with freely definable measuring range from 0 to 200mV, 2V, 20V, 200V or 500 V. Current measurements from 0 to 200µA, 2mA, 20mA, 200mA and 2A can be carried out via a shunt. With the snap-in frame, this inexpensive module can be integrated into any front panel of your own construction.
-
product
O Band Tunable Laser Source
CA9812
The CA9812 O Band tunable laser integrates a widely tunable laser with a semiconductor optical amplifier (SOA). The tunable laser is electronically tuned and can address any wavelength from 1265.00 nm to 1365.00nm. The integrated SOA facilitates flexible control of the output power and acts as a shutter when reverse biased, enabling dark tuning between channels. The device is packaged into a standard module box package, with an ternal optical isolator and a polarization maintaining fiber output.
-
product
PXI Dual Microwave SPDT Relay 18GHz 50 SMA
40-780A-522
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
RTM Actuator Signal Conditioning Board
MS 3630I
CPCI Rear IO Actuator Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on Primary and Secondary actuator interface. This card shall handle excitation signals, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 32-Channel, 2-Pole
42-614D-011
The 40-614D-011 (PXI) and 42-614D-011 (PXIe) 2-bank, 32-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 32-Channel, 1-Pole
40-614D-006
The 40-614D-006 (PXI) and 42-614D-006 (PXIe) 4-bank, 32-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Quad Channel Serial Communication Controller
CPCI-SCC04-ISO
The CPCI-SCC04-ISO Module is a quad Channel serial Communication controller with 2K Fifo per Line. The CPCI-SCC04-ISO module is based on 4 enhanced Z85233, with larger FIFOs and several SDLC improvements from Zilog. This module provides four synchronous ports up to 230 kbaud synchronous ports and up to Data Rates up to 5.0 Mbit/Sec full-duplex channels, with an independent baud rate generator for each channel.
-
product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module
43-670-XYZ-AABBCC
The 41/43-670 range is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. Available with up to four banks, each bank is capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
product
Dual Port Simulator Fiber Channel PCI Module
PCI-FC4 Simulyzer
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
product
PXI 8 Slot BRIC 330x4 2A 2-Pole Matrix
40-566A-106
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. They are available in 4 or 8-slot PXI sizes and are constructed using quality electro-mechanical relays for high switching confidence.
-
product
Open Pluggable Specification (OPS) Digital Signage Player With LGA1151 Socket 8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® H310 And TPM 2.0
OPS500-520-H
The OPS500-520-H is powered by the newest 8th generation Intel® Core™ i7/i5/i3 and Celeron® processors (code name: Coffee Lake S) with the Intel® H310 chipset. The smart cableless digital signage module has two DDR4-2400 SO-DIMMs for up to 32GB of system memory. Axiomtek's OPS500-520-H supports the LGA1151 socket-type processors offering greater flexibility for CPU selections, which is easily configured to meet various performance requirements. The OPS signage module is connected to OPS-complian...show more -
product
Amplifiers
Computer-controlled charge amplifier module features variable gain and output scaling and accepts either differential or single-ended inputs. Adjustable parameters include: accelerometer sensitivity, differential or single-ended mode, scaling, filter setting, external calibration and zero mode.
-
product
NI-9375, 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-02
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
product
SWB-2816, 8x46, 0.3 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-16
8x46, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2816 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
PXI Digital Pattern Instrument
The PXI Digital Pattern Instrument is designed for semiconductor characterization and production test. It provides 32 channels, a voltage range of -2 V to 6 V, a PPMU force voltage range of -2 V to 7 V, up to a 200 Mb/s data rate, and a clock generation rate up to 160 MHz. The module includes Digital Pattern Editor software as well as debugging tools like shmoo, digital scope, viewers for history RAM, pin states, and system status.
