Locators
are used to find or position.
-
product
Cable Test Van
The desire for faster and more efficient cable fault location as well as cable testing and diagnostics demands the ergonomic installation of equipment into vehicles. To be able to satisfy the customer's particular requirements, each system is factory-fitted into a vehicle of their choice. The size of vehicle will dictate the equipment at the planning stage. Ergonomics, taking into account the customer's needs, is paramount.
-
product
Industrial Gas Detector
OLCT 60
Teledyne Gas & Flame Detection
The OLCT 60AD version allows the sensor to be installed remotely up to 15 meters (standard), allowing detection in inaccessible locations, or in Zone 0 in the case of the intrinsically safe (IS) version. The detector units are made of 316L stainless steel, and are rugged and resistant to corrosion. Pre-calibrated sensors can be disconnected by turning the head of the unit. These “smart” sensors can be calibrated outside hazardous areas.The OLCT 60 is equipped with non-intrusive access to a safe menu. In hazardous areas, calibration can be done with an operating mode in accordance with safety rules.
-
product
Cable Fault Locator With Time Domain (Intelligent Bridge)
GT00ZD00ZY
GAOTek Cable Fault Locator with Time Domain has a reflectometer to locate faults in metallic cables and Intelligent bridge for tesing the broken line
-
product
McMurdo FastFind - Wrist Lanyard
10-91-060-001A Fast Find 210
10-91-060-001A Fast Find 210 - standard model with GPS for extra fast position location Announcing the amazing new McMurdo FastFind Satellite Personal Locator Beacon (PLB): the most compact, waterproof and versatile 406 MHz emergency location beacon available on the market today.The Fast Find is a 406 MHz Personal Location Beacon (PLB) that should be carried by individuals, who are embarking on trips into areas around the world where there is little or no other forms of communication or where other forms of communication are unlikely to work. The Fast Find acts as your personal Emergency Location Beacon, it is your last resort communication to the national and international search and rescue bodies and it should not be misused. The Fast Find is designed as a direct communication, to the 406 MHz Search and Rescue satellite system, its signal indicates that you are in need of urgent response and assistance. The location of a McMurdo Fast Find 210 GPS PLB can be determine to a typical positional accuracy of about +/- 62 metres (0.03 miles) within a few minutes of PLB activation. McMurdo FastFind PLB Manual (.pdf)Its small size belies its rugged construction and powerful output. There is no compromise. Once activated, the distress beacon will send out a signal for help, and continues to transmit for at least 24 hours, at a powerful 5 watt output, ensuring that your call for help gets through whatever the conditions. The pocket sized beacon transmits at the press of a button, to alert search and rescue services to your plight.McMurdo FastFind PLB is an essential piece of life-saving equipment, weighing in at just 5.3 oz (150g) and having the size of an average mobile telephone (actual dimensions being 1.34”/34mm x 1.85”/47mm x L 4.17”/106mm) it will slip into the smallest pocket or backpack compartment. The user can activate it in the most remote locations around the world: on land, at sea or in the air, and can be confident of being able to contact the world’s professional search and rescue services directly if they are to encounter a possibly life-threatening situation.McMurdo FastFind PLB comes equipped with an integral 50-channel GPS system and complies with rigid federal and international standards. It operates on the global COSPAS SARSAT 406MHz search and rescue satellite communication system, so a call for help will be acted upon…and fast. The McMurdo FastFind PLB is subscription FREE and does not rely on any commercial call centers. THE McMurdo FastFind PLB model transmits two signals simultaneously: a global 406 MHz signal and a 121.5MHz local signal. Once activated, McMurdo FastFind PLB’s signals will continue to transmit for at least 24 hours, at a powerful 5 watt output, the 406 MHz transmission ensures that a call for help gets through, no matter what the conditions. McMurdo FastFind PLB also includes a unique flashing SOS LED light to further assist in speeding up the user’s recovery time during night rescues.McMurdo FastFind PLB will operate in temperatures as low as -20°c and its integral battery has a user storage life of 5 years, so there’s no need for frequent battery changes or re-charging.Put a McMurdo FastFind PLB in your pocket, and get found fast.
-
product
Low Frequency Generator
LFG-200
LFG-200 is a cable test van-mountable signal generator used as part of a cable tracing and fault location set for the following applications.
-
product
Open Source Service to Help Secure and Trust Your Software
Community Attestation Service / CAS
- CAS stores all signatures inside of immudb, the standard for open source immutable databases.- CAS is protected against tampering. All attestation data is integrity-checked and cryptographically verified by the CAS client.- CAS is also protected against MITM attacks. The public key below is checked by every communication.A Software Bill of Materials (SBOM) is a list of components in a piece of software.Like a list of ingredients on food packaging -- where you might consult a label to avoid foods that may cause an allergy -- SBOMs can help companies avoid use of software that may harm their organization.If defects are later found in a specific part, the SBOM makes it easy to locate affected products.
-
product
Tone Generator
140BMC/6P
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
product
360° Edge Analytics
360° Edge Analytics fills the gap between location data and the individual business application. The Location Data Analytics technology leverages precise position data augmented by application context information to gain business insights from complex processes. Assessment, optimization as well as process restructuring will be possible with nanotron’s complete solutions based on its Location-Aware IoT Platform with Location Data Analytics.
-
product
Remote Display Kit for Post.4d
postrd
remote display kit for post4d, not RoHS compliant (can be considered test equipment, not subject to RoHS). Connects to PC Engines post4d PCI POST card (will not work with post2b or post5a). 20 inch cable, place display in a more accessible location. Ideal for software development or test fixtures.
-
product
Single Beam Echosounder, Hydrographic Survey Boat
Z-Boat 1250
Teledyne Oceanscience Z-Boats® are the number one choice for reliable, remotely controlled, hydrographic surveying in streams, rivers, lakes, and coastal waters around the world.Whether you need to reduce survey time, keep people safe during hazardous conditions, or access hard to reach locations, there is a Z-Boat to suit your survey and your budget. The Z-Boat 1250 is easy to operate. The integrated echosounder has an embedded transceiver with digital signal processing and outputs depth & temperature using NMEA 0183 data output.
-
product
Transformer Rated And Self-Contained Training Bench
Model 8803A
The PowerMaster® 8803A Transformer Rated and Self-Contained Training Bench uses an integrated Windows-based touchscreen interface to select and modify a simulated error scenario while located at the bench. This display is mounted on an articulating arm to maximize bench space and enable line-of-sight while standing.
-
product
AC Power Sources
RS Series
AMETEK Programmable Power, Inc.
The RS Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the RS series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the RS unit to its designated location (using included casters), plug it in, and the RS series is ready to work for you.
-
product
PXI 12x8 RF Matrix 300MHz 50 SMB - With Loop-Thru
40-726A-511-L
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
product
Carbon Monoxide Analyzer
707
Test flue gases at home or office spaces for the presence and location of CO leaks. With a protective rubber boot, the new 707 fits comfortably in your hand and operates with just the push of a button
-
product
Precision Locating System
Pathfinder PLS
The Pathfinder PLS is RYCOM's Precision Locating System for the damage prevention specialist...
-
product
Cable Locator
A cable locator can locate open power cables, either live or without current, with voltages up to 300 V. A cable locator can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested. Many cable locator devices also can locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy.
-
product
Portable Monitoring Receiver
PR200
The R&S®PR200 portable monitoring receiver is engineered to effectively support spectrum monitoring, interference hunting, spectrum clearance and site testing. It reliably detects, analyzes and locates signals from 8 kHz to 8 GHz and can be extended up to 20 GHz with the R&S®HE400DC handheld directional antenna and up to 33 GHz with the R&S®HE800-DC30 handheld directional antenna both with an integrated downconverter. Optimized for field operations, the R&S®PR200 provides a perfect balance between RF performance, speed and operability, while offering a range of measurement functions suitable for complex 5G signals.
-
product
PXIe-5110, 100 MHz, 1 GS/s, 8-Bit PXI Oscilloscope
785767-01
PXIe, 100 MHz, 1 GS/s, 8-Bit PXI Oscilloscope—The PXIe-5110 oscilloscope has two channels that sample up to 1 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated applications that require flexible measurement configurations and up to 100 MHz of analog bandwidth. The PXIe-5110 also features advanced PXI synchronization and data throughput capabilities. Some options also support CableSense™ technology, which can detect and locate signal path faults, changes, or discontinuities.
-
product
Sarsat Distress Signal Fixed Receiver
406
We propose to use Sarsat Beacon Monitor 406 in seaport services, rescue marine centers, coast guard rescue centers or GMDSS rescue coordination centers. However, this system has various prospective effective use fields. SBM 406 is a wide range ground COSPAS-SARSAT signal receiver which allows to locate emergency rescue signals sent by any 406MHz beacon in local responsibility area. The device can be connected to PC or laptop, and this gives possibility to observe distress signals and beacon position data on monitor.
-
product
Manufacturing & Smart Factory
Industrial Internet Consortium
The Industrial Internet will dramatically improve productivity and efficiencies in the production process and throughout the supply chain. Processes will govern themselves, with intelligent machines and devices that can take corrective action to avoid unscheduled breakdowns of machinery. Individual parts will be automatically replenished based on real time data. Every handheld digital device in the factory will report the status of every fixed device, giving personnel mobile access to real-time, actionable information. Wearable sensors will track the location of each employee in the factory, in case of emergency. The list goes on and on.
-
product
Rechargeable Submersible Strobe up to 4,000m
ST4K
The Teledyne Bowtech ST4K, Xenon rechargeable submersible strobes are self-contained, compact, high intensity xenon beacons designed for use as a visual aid to locate submersible vehicles, or instrumentation packages when they surface for recovery. They can also be used to mark underwater objects, vehicles, divers or work sites.
-
product
TSCOE4 Operator Interface Software Module
The TSCOE4 Operator Interface provides a graphical user interface for the operator or the implementer in a production environment. It permits selecting the test sequence and supports parametrization of the test. During the test sequence, the current measurement values are displayed in relation to the relevant limits and the pass/fail evaluations for each individual test. After completion of the test sequence, the global test result is visualized.In addition, there are online statistics available to the user, which show the measurement value distribution within the current batch.The editor which is supplied with the product makes it possible to adapt the user interface language to any new deployment location. Several languages – German, English and Chinese – have already been implemented and are available out of the box.
-
product
Surge Generator
Techno Instrumentation (India) Private Limited
LT to HT 11 kV and 33kV Surge Generator is an all in one solution for thumping, DC high voltage testing(Hipot-test) and burning for effective fault location in LT to HT 11 kV and 33kV cables.
-
product
High Density 68 pin
HDEterm68
The high density 68 pin SCSI II/III connector is being used for purposes other than SCSI interfaces because of board and front panel space limitations. For example in the PMC environment the SCSI connector provides an excellent size and pin count for the front panel space allowed. The SCSI connector while dense, is not easy to connect to with wiring intended to go to multiple locations
-
product
Research & Industry
XPERT 20
A small focal spot x-ray source provides increased visibility and sharpness of detail. With an X-ray source of up to 25kV and 1.0mA, the XPERT 20 provides images with the highest resolution to locate the smallest detail. Designed for use in the most limited spaces with complete shielding and other radiation safety features, the XPERT 20 is fully compliant with U.S. Federal and State requirements for radiation safety and operates with only a standard AC power source.
-
product
Ground Detection and Earth Fault Location Equipment for Ungrounded or Floating DC Systems
ZX3
The ZX3 is a ground fault locator that finds grounds (current leakage) on a battery system positive rail, the negative rail, on both rails simultaneously, in a field device, battery bank or solar array/string, regardless if they are high resistance or low resistance or in a capacitive environment. It also can provide more information about the DC ground than any other equipment available, providing maximum analyzing capabilities.
-
product
Multipoint Temperature Sensor
TSM800
The TSM800 multipoint temperature sensor is ideally suited for measurement of process temperatures over multiple locations with a single access point.Typically used in process plant vessels the TSM800 provides a cost effective alternative to mounting multiple individual sensors and their associated process vessel entries.
-
product
6-12V Heavy Duty Circuit Tester
1671
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems.1. Locate short, ground or open circuit.2. Make it easy to find out where current is present.3. The most essential for troubleshooting automotive electrical systems.4. Checks series-parallel switch and solenoid on tractor-trailer start system.
-
product
Flow Monitor
B2900
Blancett B2900 flow monitor offers advanced digital signal processing technology in an easy-to-access package. Enclosed in a spacious polycarbonate NEMA 4X housing, the electronics are located on a single board, designed for straightforward and convenient field installation. The B2900 enclosure features an LCD display with push button programming as well as a pre-drilled hole for external wiring connections, such as Modbus RTU and other outputs.
-
product
Software / Firmware
You can connect to our Ethernet test box right now and send/receive remote commands. It is located at fixed IP address 104.63.176.50 (tcp port 3001). The most often asked question about our test systems is “How easy are they to remotely control”? So we built up a test system and put it on an outward-facing IP address so that any of our customers can interact with our firmware.
