Evaluators
-
product
CDPH Standard Method for VOC Emissions
Underwriters Laboratories Inc.
The Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions From Indoor Sources Using Environmental Chambers, an expanded standard for what is commonly known as California Specification 01350, is one of the most widely used standards to evaluate building and interior products for low chemical emissions.
-
product
Vehicle Electromagnetic Field Exposure Test System
SEM-400
Beijing KeHuan Century EMC Technology Co,.LTD
Vehicles are our daily public transportation. Electromagnetic pollution in vehicles has attracted more and more public attention. The newly revised compulsory standard GB27630-201X "Passenger Car Air Quality Evaluation Standard" intends to require the electromagnetic field in the car as one of the indicators, according to GB/T37130-2018 "Measurement method of vehicle electromagnetic field relative to human exposure" The measurement method is to measure the intensity of the magnetic field in the car. In the frequency range of 10Hz-400kHz, the electromagnetic field measurement result should meet the public limit requirements of GB8702-2014 for electromagnetic exposure.
-
product
MicroSemi-SiC-Module / Evaluation Board
EV-MS4135PL1Z-U1 Pre-Release
High power evaluation board, up to 1200V & 50A @ 200kHz switching frequency featuring the combo ADI ADuM4135 isolated gate driver + LT3999 isolated power supply controller + Microsemi SiC power module in half bridge configuration.
-
product
Magpie 2 Database Evaluation Software
OTP2 module no.171
LXinstruments Magpie 2 is an advanced evaluation and data mining application for our test database. The data to be evaluated can be pre-selected using complex, easily configurable filters. Based on the selected data, reports and trend analyzes can then be created and statistical investigations, machine and process capability analyzes can be carried out. The administration of the database is also easily possible for appropriately authorized users via a graphical user interface.
-
product
Sound Quality Evaluation Function for O-Solution
OS-0525
The sounds generated from the equipment are mainly measured by evaluation based on general analysis such as sound pressure level, FFT analysis and 1/3 Octave analysis. However, since those analysis don’t take into consideration the human hearing characteristics enough, sounds with even the same analysis result may give different impression.When a human listens to a sound, various sensations such as loudness, sharpness, and roughness occur.
-
product
Cartridge Testing
Print Quality Text and Graphics. Seal Evaluation. Toner Hopper Seal Performance. Remanufactured and Recharged Cartridges. Machines and Multifunctional Products
-
-
product
Magnet Temperature Characteristics Apparatus
TDF
Evaluation of thermal stability of varieties of permanent magnets including rare-earth permanent magnet. TDF-5-200auto This apparatus automatically measures and analyzes reversible temperature coefficient(a) and irreversible temperature coefficient (Flux loss ?f) of magnetic flux density of rare-earth permanent magnet in the wide range from low to high temperature.
-
product
Axial Force And Torsion Testing Machine
Evaluation Testing That Approximates Operating Conditions of Materials and Parts - Loading methods similar to actual usage - Allows simultaneous application of axial and torsional loads to samples
-
product
PCI Evaluation Board
BCM91125E
The BCM91125E is a full-length PCI evaluation board with the SiByte® BCM1125H MIPS processor System on a Chip (SoC). The board is designed for software development and developing PCI applications, which require high-performance processors. The BCM91125E can be plugged into a PCI slot in any PC, workstation or server, or can be used as a stand-alone device.
-
product
Hydrogeology
HAPPIE
The H.A.P.P.I.E. program (Hazard of Aquifer Pollution Potential Impact Evaluation) provides a conservative answer to the problem of determining risk levels in emergency conditions, which means that areas where illegal waste disposal sites, overflows and ruptures of impermeable sheeting are present and where water withdrawal should be discontinued can be identified. H.A.P.P.I.E. in fact offers a conservative response to the problem of the determination of the environmental impact in critical conditions that can usually be correlated to the requirements of defining areas in which the supply operations should be interrupted in emergency conditions, therefore in very short times and without the possibility of obtaining an accurate collection of the hydrogeological data.
-
product
SINE (Sinusoidal) Targets & Arrays
Sinusoidal Target Arrays have been recognized as a superior test method for a variety of applications, from moiré contouring to reliable MTF Evaluation of materials, lenses, cameras, and electro-optical systems (Follow the hyperlink to learn about using Sinusoids for MTF eval). Sinusoidal Pattern Arrays are manufactured on two different materials for both reflective and transmissive applications. Because of the inherent limitations of reflective materials, the maximum spatial frequency of the reflective pattern arrays is limited to 20 cycles per mm, while the transmission film arrays are offered in various sizes up to 256 cycles per mm. In addition, the sinusoidal arrays are available in a Single Frequency Grating or with Multi-Frequency Gratings. If instead of continuous sinusoidal frequency, you are looking for a square wave frequency design, then look to the Ronchi Gratings page. Should you need to alter the size of the pattern or the substrate, fill out our Custom Test Targets and Charts form and start the conversation.
-
-
-
product
FRAMOS SLVS-EC RX IP CORE
Sony’s SLVS-EC interface standard has emerged as the best high speed interface to Sony’s best image sensors, enabling higher throughput, greater signal integrity, and simpler designs. Engineers developing solutions using Xilinx FPGAs and SoCs can take advantage of FRAMOS’s SLVS-EC RX IP Core, Evaluation Board and tested source code examples. Device builders and camera vendors can de-risk the design while reaping the benefits of Sony’s latest high-speed interface.
-
product
Paper Softness Tester ZRD-T1
The ZRD-T1 Paper Softness Tester is a device designed to objectively measure the softness of paper products, such as tissues, toilet paper, or specialty papers. Softness is a complex tactile property influenced by factors like surface smoothness, flexibility, and bulk compressibility. It is widely used in industries such as tissue manufacturing, hygiene product development, textiles, and packaging to ensure compliance with quality standards and end-user comfort requirements. This test instrument conforms to many national and international standards: ASTM D2923: Standard Test Method for Rigidity of Paper – Measures bending resistance to determine stiffness. ASTM D6828: Standard Test Method for Stiffness of Nonwoven Fabrics – Evaluates drape and flexibility in materials like medical textiles or wipes. TAPPI T498: Bending Resistance of Paper (Gurley Method) – Quantifies resistance to bending forces, inversely related to softness. GB/T 8942: Chinese Standard for Softness Testing of Household Paper – Aligns with consumer expectations for tissue and toilet paper tactile quality. ISO 12625-9: Softness Evaluation of Tissue Products (optional add-on).
-
product
Evaluation Units and Analysis Software
Benefit from over 40 years of experience in inline and laboratory beverage analysis: Connect Anton Paar’s versatile and well-proven evaluation units to all generations of Anton Paar density, sound velocity, concentration and CO2 sensors. Let the data acquisition and visualization software master complex measuring tasks for you – bringing home the precision that marks measurement solutions from Anton Paar.
-
product
SMARC V2.0 SoM Evaluation Kit With I.MX8M Quad/Dual 1.5 GHz/1.3 GHz (Industrial) SoC, 4GB Memory, 64GB EMMC, CAN, MIPI CSI/DSI, And HDMI 2.0
SCM180-180-EVK
*Ultra-Low Power i.MX8M Dual/Quad A53 Core*Single M4 Core*HDMI 2.0a up to 4K*Dual Channel LVDS*MIPI CSI*10/100/1000 Mbps Ethernet*USB3.0, USB OTG*PCIe 2.0*CAN 2.0B*Audio
-
product
COM Express Type 6 evaluation carrier board
ATX-M-CC462-T6
The ATX-M-CC462-T6 is a fully featured COM Express Type 6 evaluation carrier board designed for use with the WINSYSTEMS Intel® Tiger Lake UP3 COM Express and other COM Express Type 6 modules.
-
product
Laser Type PM Sensor Evaluation Kit
Panasonic Industrial Devices Sales Company of America
The SN-GCJA5L Laser Type PM Sensor Evaluation Kit provides design in concept prototyping and testing of the Panasonic SN-GCJA5 Laser Type PM Sensor.
-
product
Accelerate the Process of Evaluating
Simulia
Powered by the Powered by the 3DEXPERIENCE® Platform, SIMULIA delivers realistic simulation applications that enable users to explore real-world behavior of product, nature and life.
