Collectors
-
Product
Open Loop Current Sensor
C03 30A
-
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in industrial, commercial and communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
Product
Condition Monitoring
Falcon
-
The ultimate portable vibration data collector and analyzer. With a wide range of optional features available, the FALCON can be configured to perform balancing, run up coast down, frequency analysis and more.
-
Product
Dust Collector Timer Controller
DCT1000DC
-
Simplify your on-demand cleaning requirements with the Series DCT1000DC Dust Collector Timer Controller. Relying on one timer board for on demand and continuous cleaning applications, the DCT1000DC eliminates external devices such as pressure switches, relays and timers.
-
Product
PXI/PXIe 16-Channel Digital Output Module
40-412A-024
Digital Output Module
16-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
Digital I/O Module
ND-6050
Data Acquisition Module
- Interface: RS-485- 7 TTL digital inputs- 8 open collector DO- Output up to 30V, 30mA max. load- Programmable input polarity
-
Product
Settling Dust Chamber
-
Dust material is placed in a collector, or trough, at the bottom of the chamber, where air nozzles periodically agitate the material, causing a cloud in the chamber. After the agitation, the dust cloud is allowed to settle onto the test sample, which sits above the collector.
-
Product
8-Ch Digital Output Module
ADAM-3656
-
Rated voltage : 8 ~ 30 VDCSupports open collector (Sink) output typeOver voltage protection : +40 VDCOpto-isolator response time : 150 us (max)Pulse output frequency : 1 KHzIsolation voltage : 2000 VDCRated current : 200 mA (max load)-40 ~ 70°C operating temperature
-
Product
Precipitation
-
Bristol Industrial & Research Associates Ltd
Biral provides a wide range of instruments for the detection, measurement and study of precipitation. We offer the following classes of instrument: Precipitation Monitors to detect the presence of precipitation Rain Gauges for the measurement of precipitation amount Laser Precipitation Monitors for the detection and classification of precipitation in real-time Micro Rain Radar for the measurement of precipitation in a column up to 6km high Precipitation Collectors for the collection of precipitation for subsequent chemical analysis
-
Product
Remote Indicator System
LineTroll R110CQ
-
The fault indicator use a 2.4GHz ISM band short-range radio to communicate with the collector mounted on the pole. The collector communicates with up to 9 fault indicators. Both the indicators and the collector are powered by long-life lithium batteries for long and maintenance free operation.
-
Product
4 Thermocouples/RTD Ch
APCI-3200-4
-
18-bit resolution, 16-bit accuracyEach channel can be configured either for thermocouples/RTD or as an analog voltage input channel4 analog input channels for thermocouple typesJ, K, T, E, R, S, B, N - or 2 diff. analog input channels for the acquisition of resistance temperature detectors (Pt100)- or 16 SE/8 differential analog voltage input channels, ± 2.5 V8 independent current sources for resistance temperature detectors (RTD) and one current source for cold junction compensationCold junction compensation (on separate screw terminal board PX 3200)Gain and offset calibrationLinearisation through table and calculation for the thermocouple types J, K, T, E, R, S, B, N and RTDsProgrammable gain16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz (other rates on request)4 digital input channels, 24 V and 3 digital output channels, open collector, isolated
-
Product
Quadrature Sensor
-
SPECTEC Innovative Sensor Solutions
DIGISPEC Hall Effect Quadrature Sensors provide two digital output signals, 90º out of phase to each other, detecting speed (down to true zero speed) and direction of rotation of gear teeth and ferrous targets. Gear teeth as small as module 0.10" wide can be sensed. Standard output is provided from a 2.2kOhm internal pull-down resistor to a collector, which can sink 25 mA. Open collector can be provided. Output is protected against reverse voltage.
-
Product
Hall Effect Sensor
907 XP (Explosion Proof)
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
Product
Split type Pulse Current Sensor
CTF-05K
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Pulse current detection for power demand meter.*Clamp type CT.*Open collector output.
-
Product
Coupled Cavity TWTs
-
Communications & Power Industries
• Frequencies from 2.7 to 37.5 GHz• Peak levels: 500 W to 180 kW• Cooling type: air, liquid, conduction• Depressed or grounded collectors• CW (Continuous Wave) and Pulsed
-
Product
Klystron HPAs
-
Communications & Power Industries
CPI's GEN IV klystron power amplifier (KPA) is the overwhelming choice among Direct-to-Home service providers for uplink service, and is also very popular for other broadcasting applications. As the first KPA to utilize multi-stage depressed collector (MSDC) technology, the GEN IV offers by far the best combination of high power, high efficiency, small size, low heat dissipation and low acoustic noise in its class.
-
Product
16-Ch Digital Output Modules
ADAM-5056D
-
Operating voltage: 30 VmaxDigital output: Open collector to 30 V, 100 mA max. loadOutput status hold functionPower consumption: 0.5 W (typical); 0.84 W (max.)Power dissipation:300 mW for each channelLED indicator: On: Output logic level "1"Channels: 16
-
Product
PXIe 64-Channel Digital Output Module
42-412A-021
Digital Output Module
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
DCDC
JA/JP Series
-
The 15-Watt JA/JP series operates over an ultra wide range of 9-36 Vdc or 20-72 Vdc. Efficiencies of 80% are typical over varying load conditions of 25% to 100%. Additional features include input reverse polarity protection, remote on/off control, logic compatible with CMOS or open collector TTL, short circuit protection with auto restart, overvoltage protection, and an operating temperature range of -25°C to +71°C with no derating. Units are packaged in a six-sided continuous shielded case for EMI/RFI protection and measure 2.0” x 2.0” x 0.40”.
-
Product
Digital Geological Data Collector
TECTRONIC
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Measurement and reading of azimuth of dip and angle of dip in one single operation (according to Clar method)*LCD display and memory for approx. 4.000 measurements*RS232 interface*Display indication 1° (360°, 400g, 6400– or 6300– selectable)*Many additional functions like measurement of magnetic field intensity)*Circular spirit level*Accessories upon request (Software, tripods, battery packs, …)
-
Product
System and Collection Tester
SysColl
-
For certification in many markets, performance of the complete factory made system (for example thermosiphon systems) plays an equally important role as collector performance. Our SysColl test stand is a combined test facility for performance testing of both solar collectors and solar thermal systems. This allows you to take advantage of a flexible two in one test solution.
-
Product
Mechanical Load Tester
-
Solar modules and collectors, whether on roofs, in façades, or freestanding, are often exposed to high mechanical stress or load: A deep layer of snow or strong winds can greatly affect the materials and connections. Mechanical load test stands accurately test the durability of PV modules and thermal solar collectors.
-
Product
Automatic Tablet Weighing System
CIW 7.2/7.3
-
With the automatic weighing system CIW 7.2 / 7.3 LAB you weigh tablets, dragees, capsules and similar products. Based on the UTS tablet testing systems by Kraemer Elektronik, the standard unit offers a tablet separation system and a special transport star for precise positioning of the test specimen on the integrated scale.The CIW 7.2 / 7.3 LAB in the laboratory version is now equipped with the database-driven, intuitive all-in-one touch software and no longer requires additional software solutions for most areas of application.The functionality of the software can be extended modularly – matching your needs and requirements.Alternatively, you can expand the CIW 7.2 / 7.3 LAB weighing system with a 12-station feeder and/or a 12-station collector to perform multiple defined tests (12-station feeder) in one measuring cycle. All cleaning-related parts can be easily and quickly disassembled without tools.The CIW 7.3 LAB model is nearly identical to the CIW 7.2 LAB, but additionally features a precise measuring device for thickness determination.
-
Product
Vibration Analyzers & Data Collectors
-
Wireless Vibration Analyzers and Data Collectors are replacing analyzers all over the world. Their easy connectivity and fast data collection timings make them the most convenient solution for vibration analysis nowadays. Digivibe products are the Vibration Analyzers with the largest number of functions in the market. They integrate advanced functions for Vibration Analysis and Dynamic Balancing with new Triaxial Wireless technology making them more portable and versatile. Furthermore, their compatibility with current mobile devices make them very easy to use and ultra-portable. ¡Meet our improved functions for bearing and gearbox analysis!
-
Product
Digital I/O Switch Card - 96 Open Collector Channels in 12 Groups of 8 Bits Each
1260-14/14C
Switch Card
The Astronics 1260-14 Digital I/O Switch Card provides 96 open collector channels in 12 groups of eight bits each. With the open collector version each independent group can utilize a separate internal or external pull-up supply up to 32VDC.Each channel can be configured as an input or an output and individually controlled in the asynchronous mode, or be synchronous with other channels.
-
Product
PXI/PXIe 16-Channel Digital Output Module
42-412A-024
Digital Output Module
The 40-412A-024 (PXI) and 42-412A-024 (PXIe) are 16-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
Hail Impact Tester
HIT
-
Hailstorms can cause severe damage to modules and collectors. Our test stand enables you to carry out tests according to international standards. The hail impact test stand uses an air-pressurized launcher that shoots ice balls representing hailstones of a predetermined size at the module or collector mounted on the support frame.
-
Product
Vibrocollector
STD-500
-
The STD-500 Vibration Collector is a portable, single-channel vibration measuring instrument with built-in spectral analysis capabilities designed for regular inspection of equipment condition.
-
Product
Filters, Collectors, Separators, Purifiers
-
Parker's filters, separators and purifiers come in a variety of options and media and are used to filter out air or fluid contaminants in an array of industrial and commercial applications.
-
Product
Renewable Energy
-
ETAP's Renewable Energy offering enables designers and engineers to conceptualize the collector systems, determine wind and PV solar penetration and perform grid interconnection studies.
-
Product
CPCI 48 Optically Isolated Outputs Card
CPCI-48OUT
Controller
The output board consists of FPGA controllers for DC output control. An FPGA provides the timing and control. Each output has its own optical isolation, and supports an open collector output. An PCI controller provides the interface to thehost computer. All I/O is accessible from the front panel.
