-
Product
CPCI Based 486DX4 Board
MS 1501
-
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS
-
Product
PCI Daughter Boards
DB-24SSR
-
The DB-24SSR/DB-24SSRDC includes 24 normally open, or form A, solid-state relays The board interface to filed logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The user can use the DB-24SSR/DB-24SSRDC to switch high voltage load, up to 240 VAC/50 VDC and up to 4 A. The relay is energized by applying a 5-voltage signal to the appropriate relay channel on the 50-pin header or 37-pin D-sub connector. Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated. Because there is a D-sub 37-pin connector on the board, the user may use it to interface to any TTL output board. In other words, the user may use it as a general purpose solid state relay output board.
-
Product
Dynamic Digital I/O (3U), 16 Ch., Per Pin Control, Up To 200 MHz W/256MB Memory & LVDS
GX5293
Digital I/O
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 16 ch., per Pin Control, up to 200 MHz w/256MB Memory & LVDS
-
Product
Debug Adapters
-
One thing is sure in the life of an embedded developer - your next microcontroller development board will be fitted with a different debug connector to the one used in your previous design.
-
Product
Digital Input Board, 32 Isolated Channels, 24V
APCI-1032
-
32 digital inputs, 24 V or 5 V, incl. 16 interruptible inputs Optical isolation 1000 V Input filters Protection against pole reversal
-
Product
Connector Block, 50-Pin D-Type, Female
40-965A-050-F
D-Sub Female Connector Block
The 40-965A-050-F connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
Sensor Board for micro:bit
-
The MonkMakes Sensor Board for micro:bit allows you to sense sound level, temperature and light level. You can connect it up to your micro:bit using alligator clips.
-
Product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Custom Test Connectors and Sockets
-
Custom test sockets are traditionally expensive to build and maintain. To reduce these costs, consider: Using rapid prototyping techniques to build a housing. Using replaceable Z-Axis Connectors. Depending on board layouts and compressed height, these sockets or test fixtures can achieve high numbers of mate/de-mate cycles and operate at GHz frequencies.
-
Product
Plugbord
3682
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience. Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
Product
LAN (supporting POE) Expansion Board
OP-SB89
-
OP-SB89 is an expansion board for Ethernet LAN, inserting into a slot of battery drive portable data communication analyzer (LE-8200A/LE-8200). It supports the PoE (Power Over Ethernet) standard, and able to analyze the communications and power consumption at the same time.
-
Product
Hign Speed Bare Board Test System By Non-Contact Test Technologies
SX-750SUPERⅣ
-
Suitable for a wide range of applications. Can be connected to a wide range of machines: from hand press to reel mechanism and in-line mechanism. We offer docking with our customers own machines. Compact main tester simplifies integration via installation inside a mechanism. If requested, we will perform a study to decide which functions should be added.
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
Actuation Methods for In-Circuit Test Fixtures
-
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
Product
6U CPCI Processor Board
CP67001
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP67001 is a CompactPCI® processor board based on China local-manufactured Phytium FT1500A/4 4 cores ARM processor, with more than 10-year lifecycle. Designed with ARM v8 Architecture, 28nm process technology and fine-grained power optimization technologies, its CPU integrates 4 ARM cores with CPU clock speed up to 2.0 GHz. Combined with the maximum power consumption of 15w, CP67001 is highly applicable for making low-power-consumption solutions.Equipped with Intel82580, CP67001 supports 4x Gigabit Ethernet; 4x SATA 2.0 and 8x USB 2.0; 1x16 PCI Express for XMC and PMC; SM750 graphic controller with resolution up to 1920x1080p. CP67001, as a single board computer has up to 64GB flash memory, provides outputs including HDMI, DP, DVI and VGA, and provides 2 serial ports with one port supports RS232/RS422/ RS485 configurable through software. In addition, CP67001 supports GPIO and can meet customized demands in different situations.
-
Product
Analog Backplanes
MSXB 030
-
Analog Backplanes provide expansion slots to accommodate compatible analog external boards. Analog Backplanes are passive, and connect all signals in each of the expansion slots in parallel. All expansion slots are identical
-
Product
SparkFun Single Lead Heart Rate Monitor
AD8232
-
The AD8232 SparkFun Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal from the PR and QT Intervals easily.
-
Product
Gyro Test Panel
TA-256
-
Designed to test the KI256 / KI258 panel mounted Flight Director gyros. The panel contains a power supply, the special manufacturers recommended rate board required by SA-103 to properly verify outputs As well as all other electronics required to support by the book testing.
-
Product
8 Channel 100 MS/s 16-bit ADC
SIS3302
-
The SIS3302 is the 16-bit extension to our 100 MS/s digitizer family. It is the 2nd DDR2 memory based digitizer unit in the SIS33xx family. The board is used for the readout of high resolution detectors, accelerator controls and other applications.
-
Product
CPSI-S.0 Standard Compliant Peripheral Board Controlled by a PCIe Channel Derived from a Backplane Connector P1
MIC-3811
Backplane
It is a dual mini-PCIe carrier board with two onboard SIM card holders and mini-PCIe connectors, routed by PCIe and USB2.0 interface. It allows connection with different types of Mini PCIe form factor add on cards like Wi-Fi/3G/4G LTE/GPS/DIO/CAN/ and MVB modules, either full- or half-size style.
-
Product
Rackmount IPC
-
Industrial Computer Chassis series offer motherboards, backplanes and single board computers, such as IPC chassis, ATX chassis, IPC enclosure for Servers, Server Boards, Server Chassis, and Server Systems. The IPC chassis series build an essential bloc for performance demanding applications.
-
Product
Pico-ITX SBC With Intel® Pentium® N3710 & Celeron® N3060 Processor, HDMI (VGA)/LVDS, LAN And Audio
PICO300
-
The PICO300, an extreme-compact fanless pico-ITX motherboard, is built with the Intel® Pentium® N3710 or Celeron® N3060 processor (codename: Braswell SoC). One SO-DIMM socket is provided to support up to 8GB of DDR3L-1600 memory. The PICO300 is supported in dual display configurations along with one 18/24-bit single/dual-channel LVDS and a choice of VGA or HDMI. Furthermore, the tiny 2.5” pico-ITX embedded board features Intel® integrated Gfx graphic engine to build excellent media and graphics performance capability. In addition, the compact size of the pico-ITX form factor also makes the PICO300 suitable for space-constrained embedded applications. It runs fanless operation, and supports -20°C to +60°C operating temperature. Combined all features as above, the PICO300 is ideal for any media editing, imaging, graphics and video intensive applications that be applied for a wide array of industrial IoT industries.
-
Product
Diode Laser Spectroscopy
-
Diode Laser Spectroscopy by Mesa Photonics: Herriott Cell and OEM laser diode controller boards.
-
Product
Mini PC
DS-410
-
Palm-sized mini PC designed for hospitality and signage applications. Stylish Aluminum Die-cast Design with Intel Atom® J6412 processor. Optimized GFX performace by on board 4GB/8GB DDR4 (3777Mhz). Support HDMI 2.0 up to 4K(3840 x 2160), and VGA up to Full HD.
-
Product
3.5" Single Board Computer
RSB-4810
Single Board Computer
Advantech’s RSB-4810 is an Arm-based 3.5" single board computer (SBC) powered by Rockchip RK3568 SOC. It leverages 4 x Arm Cortex-A55 cores, a 1.0 TOPs NPU, and a Mali-G52 graphics engine. RSB-4810 provides USB 3.0, PCIE 3.0, SATA 3.0, 2 x Gigabit Ethernet ports, a single channel LVDS (shared with MIPI-DSI), 6 x UART, and 2 x CAN for embedded applications. RSB-4810 also features Mini-PCIe, M.2 E-Key, and SIM card slot for Wi-Fi 6, BT, 5G/LTE, and AI acceleration modules. These features make Advantech’s RSB-4810 an ideal solution for entry level edge AI computing in AIoT applications.
-
Product
MTM Development Board Kit
-
REDUCE MTM WIRING COMPLEXITIES: The MTM Development Board Kit development and testing of embedded and high-level programs with comment MTM modules.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5912-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
-
Product
224 Channel Digital I/O Modular PXI Card
GX5731
Digital I/O
The GX5731 is a 6U modular digital I/O card with 224 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5731 offers the highest density in the industry for a single PXI plug-in board. Of the 224 channels, 128 support TTL levels with the direction of each group of eight channels programmable as input or output. The other 96 channels can be used for customized I/O using MTS' GX57xx series I/O modules.
-
Product
SparkFun GPS Breakout
NEO-M9N, Chip Antenna (Qwiic)
-
The SparkFun NEO-M9N GPS Breakout with on-board chip antenna is a high quality GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations witn ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions, increasing precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
