Power Factor
measures true power over apparent power.
-
product
Injection Transformer
J2100A
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
product
Arc Ingintion Tester
The product is designed to carry out Arc Ignition Test as per IS/IEC 60947-1 Clause 8.2.1.1.2 (material used for electrical products). The adjustable current source is 230V AC @ 33A. The load is adjusted to get 32.5A at 0.5 power factor. Included on control unit are Digital Voltmeter, Digital Ammeter, Digital Power Factor Meter and Micro Controller based programmable Sequence Timer with LCD display for display & setting. The arrangement is made to mount the test piece with electrodes as per the specification given in the standard.
-
product
Power Meter
8015 PM
Standard Electric Works Co., Ltd
● Determine the running cost of your appliances.● Measure voltage, current, frequency, watt, power factor, and greenhouse gas emissions.● Optical USB to RS-232 data transmission.● 2 Optical LEDs are built-in for data transfer.● Transferring and showing real-time data to a PC.● Make informed decisions when purchasing appliances and equipment.● Reduce your electricity bill.● Calculate electrical expenses by real, hour, month. ● Can make different kinds of plugs for different countries / areas, such as Type B, E, G, I plugs.....etc.● Data communication function.● Freely set upper and lower limit for V,A,W and alarm when measured value is out of limit.● Backlight function.
-
product
Power Analyzers & Wattmeters
Measurements International Ltd.
Direct Replacement for 2010A Wattmeter in the AccuLoss® Loss Measurement Systems, Basic Power Accuracy < 0.005 %, 10 Current Ranges, 2 Voltage Ranges, Line-and-Line and Line-to-Ground Voltage Measurements, Full Power Factor Range, Complete Waveform Analysis, Total Harmonic Distortion Analysis, Phasor Analytical Representation.
-
product
Electronic Transformer Test System
UI2000-ET
• Input characteristics analysis 1) Measure Vrms (10-300V) Lrms (0.04-4A) W, PF, Hz, total harmonic and 0-50 component of harmonic 2) Accuracy: ± (0.4%reading + 0.1%range + 1digit) • Output characteristics analysis 1) Measure lamp voltage (1-60V) lamp current (03-20A) lamp power, crest factor and oscillatory frequency 2) Accuracy: Class 2 • It can print without compute, and provide the communication port for PC
-
product
Injection Transformer
J2101A
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
product
AC Power Source
61600 Series
Built-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable voltage,current limitComprehensive measurement capability,V, Hz, Irms, Ipk, Iinrush, P, VAR, VA, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlOne-key recall for 9 different voltage and frequencyProgrammable slew rate setting for changing voltage and frequencyAnalog input for power amplifierOptional Analog programming interfaceOptional GPIB and RS-232 interface(Model 61601~61605)Full protection: OP,OC,OV and OT protectionEasy use graphic user interface: softpanel (option)Capable of delivering power output up tp 90KVA by implementing Master-Slave operation
-
product
AC/DC Power Clamp Tester
IBL-307
International Biological Laboratories
This Digital Clamp On Power Meter Model 307 can be used to measure True Power, Apparent Power and Power Factor in single phase circuits. It measures AC/DC Current and incorporates a frequency counter. It is autoranging type Digtal Clamp On Power Meter and has 3-3/4 Digits 4000 Counts with 40 segment analog bargraph LCD Display.
-
product
Digital Panel Meter
MW(Q)-5A
Mx-5A meter to provide power (Watt or Active Power or Re-active Power or Power Factor), high-precision measurement, display and remote communication capabilities.Additional purchase: 1 group of relay outputs, 1 analog output, an RS485 communication output (the Modbus RTU Mode) interface, so that can be installed in power management, remote input and output, alarm and variety of remote communication control the use of needs.120mm (D) is ideal for assembling in panels with limited penetration depth.
-
product
Power Meter
2015 PM
Standard Electric Works Co., Ltd
● Determine the running cost of your appliances.● Measure voltage, current, frequency, watt, power factor, and greenhouse gas emissions.● Log and Recall function.● Enable users to read the data in memory directly on the meter without connecting to a PC. ● Optical USB to RS-232 data transmission.● 2 Optical LEDs are built-in for data transfer.● Transferring and showing real-time data to a PC.● Make informed decisions when purchasing appliances and equipment.● Reduce your electricity bill.● Calculate electrical expenses by real, hour, month. ● Data communication function.● Freely set upper and lower limit for V, A, W and alarm when measured value is out of limit.● Backlight function.
-
product
Power Factor Controller
R5&R8
DUCATI energia introduces the new and innovative R5 and R8 power factor controllers. The compactness, the latest technology and the complete range of features make the R5 and R8 models extremely adaptable to any application context in the field of power factor correction systems for both single-phase and three-phase networks of low and medium voltage with a lot of connectivity options.
-
product
Multifunction Power Transducer With Display
Model TRMT MULTIFUNCTION POWER
Kusam Electrical Industries Limited
• Easy Installation & Space saving.• Simultaneous detect & display : - Individual Phase to neutral Voltage - Individual Phase Current - Individual Phase watt. - Frequency - Phase to Phase Voltages. - - Power Factor - - Total Watt - - Total Var
-
product
6U CompactPCI Intel® Atom® X6413E Processor Blade
cPCI-6660
The cPCI-6660 Series is a 6U CompactPCI single-board computer available in single-slot (4HP) or dual-slot (8HP) width form factors, powered by the Quad-core Intel Atom® x6413E Processor. The cPCI-6660 now supports dual-channel DDR4-2400-3200MT/s memory with In-Band ECC (IBECC) for enhanced reliability. It features a 5V power input, four 2.5GbE Ethernet ports (3x RJ-45 and 1x M12 X-coded), onboard iSLC, and offers flexible storage options, including an optional 2.5" SATA drive space or mSATA, configurable by BOM.
-
product
High Precision Power Meter
MPM-1010/1010B
MPM series intelligent electrical parameter measuring instrument is a set voltage test, current test, power test. Multi-functional measuring instrument with integrated power factor and high-speed processor inside.
-
product
High Performance Programmable AC Power Source
61500 Series
Chroma 61500 Series have built in 16-bit measurement circuits and firmware utilities to measure the true RMS voltage, current, true power, apparent power, reactive power, power factor, current crest factor, and inrush current.
-
product
Resistive & Capacitive AC Load Bank
RCD
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.
-
product
300W to 1008W - Single Output
PFE Series
*Low profile, small size*100°C baseplate temperature*High Power Density*High Efficiency*Suitable for conduction cooling*Power Factor Corrected (PFC)
-
product
Single Phase Portable Energy Meter Test Bench Type KP-P1003-C
Bofa Instrument & Equipment Co., Ltd
Single-phase portable test bench, Type KP-P1003-C, is an ideal device to test all kind single-phase energy meters accuracy below 1.0. The equipment can generate single-phase voltage, current and all power factor. The equipment is box structure, light, and easy to carry, it is a very ideal device for energy meter factory to adjust meter at production line, it also can be used as testing equipment in R&D institute.
-
product
Resistive & Inductive AC Load Bank
RL
Resistive & reactive load banks are able mimic motor loads and electromagnetic devices within a power system as well as purely resistive loads by offering the ability to set a specific power factor (pf). Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit. JUNXY has an extensive range of resistive & reactive load banks to simulate these types of loads on a power source and the transformers, relays, and switches which will distribute the power throughout your facility.
-
product
Automated Data Collection
Three-phase multifunctional static electricity meters AMT B0x-FxxTIIx are determined for measurement of active and reactive electric energy, instantaneous active power for consumption and supply, maximum demand, voltage, current and power factor in threephase four wires networks in diredct or indirect connection.
-
product
Power Clamp Meters
Precision Mastech Enterprises Co.
Advanced electrical testing tools with hinged, jaw-like clamps that measure AC/DC current, voltage, power (kW), power factor, and harmonics in live conductors without breaking the circuit.
-
product
1000W, 1500W HSM Watt Power Supply Models
Series HSM
The Kepco HSM series comprises a group of ten models, seven 1000 watt power supplies with outputs from 3.3 volts to 125 volts and three 1500 watt power supplies with outputs from 24 to 125 volts. All models feature current sharing for parallel operation and redundancy applications. Kepco¹s 1000W HSM have a wide-range input (90-277V a-c). The 1500W models operate 180-277V a-c. Both incorporate power factor correction to meet EN 60555-2 and EN 61000-3-2. These modern power supplies operate at 100KHz using current mode control to provide rapid response to source and load changes and tight stabilization.
-
product
Automatic Battery with Filters with Standard Contactors
BATLVF1200
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralizedcompensation of power factor in low voltage instalations
-
product
Resistive & Capacitive, Inductive AC Load Bank
RLC
Inductive & capacitive load banks are reactive only and must be used in combination with a resistive load bank to provide the desired load profile to test a power system. Reactive loads banks can provide either a leading power factor (Capacitive) or lagging power factor (Inductive).
-
product
Resistive Load Banks
R Series
Load banks are devices which contain resistive, inductive and/or capacitive loads, apply the load to an electrical power source and dissipate the power of the electrical source. Portable and stationary resistive load banks incorporate as low as 1 kW load step increments for testing small to large generating sets. The fine control resolution ensures accurate load control and power factor targeting adjustments.
-
product
PFC Controllers
Renesas' power factor correction (PFC) controller family uses boost topology and are suitable for AC/DC power systems, up to 2kW and over the universal line input. These PFC controller IC's operate in continuous conduction mode (CCM), and the small external components result in a low cost design without sacrificing performance.
-
product
Power Quality Testing
Weshine Electric Manufacturing Co., Ltd
Transformer K Factor, Power factors(PF)and displacement factors, Short-term voltage flicker, .Three phase unbalance (Current and Voltage), Waveform real-time display(4 channels voltage /4 channels current) True RMS values of voltages and currents
-
product
Digital PFC Controllers with Power Metering
Are digital power factor correction (PFC) controllers that provide accurate input power metering capability and inrush current control for ac/dc systems.
-
product
AC / DC Digital Power Analyzer
4016（800Vp,20Arms/200Ap）
To analyze AC/DC power source, it requires a lot of parameters. Such as voltage(V), current(A), power factor(PF), Total Harmonic Distortion(THD), Crest Factor(CF), Inrush current, etc. To meet power saving regulation, the standby power measurement must be done. In this video I will show you how to operate this Prodigit Power Analyzer 4016. Furthermore, I explain what the parameter's meaning.
-
product
Power Supplies
NEO ECO SERIES
Get economical power today with the NeoECO C Series, Antec's high-efficiency power supply solution. Featuring 80 PLUS® BRONZE certification, a quiet double ball bearing 120mm fan, and universal input with active power factor correction (PFC), the NeoECO C series gives you a cooler, quieter system all powered by Continuous Power. The NeoECO C series also features industrial safety protection, including short circuit and over voltage protection, for stable and reliable power no matter what.
