Magnetic Field Meters
Measure magnetic flux density/field strength.
See Also: Magnetic Field, Magnetic Field Mapping, Magnetic Field Probes, Magnetic Field Sensors, Magnetic Field Test
-
Product
Magnetic Field Cancelling System
MK-1
-
Single axis magnetic field cancelling system for MRI scanners and biomagnetic applications. This system is used when the magnetic field sensor cannot be placed within the shielded volume. For example, in MRI applications the sensor is usually installed outside of the shielding room because of the MRI scanner's high fringe field.
-
Product
Magnetic Flaw Detector (Magnetic Yoke)
NOVOTEST MPD-DC
-
Magnetic Flaw Detector (Magnetic Yoke) NOVOTEST MPD-DC applies in circumstances where the electric equipment mustn’t be used or prohibited by the rules.
-
Product
Optical Power Meter - MATRIQ
Power 1400 Series
Power Meter
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
Product
Field Testing
-
Electronic force measuring device with digital display in MN / m², switchable for load plate.
-
Product
Magnetic Encoders
-
The magnetic encoder detects rotational position information as changes of the magnetic field, converts them into electrical signals, and outputs them. The simplest magnetic encoder consists of a permanent magnet and a magnetic sensor.
-
Product
Magnetic System
NMR-EA300 System
-
The NMR-EA300 system is the reference for calibrating magnetic sensors. It allows to generate an absolute magnetic field at <±10mG (0.1 uT) without temperature drift (<0.1ppm/C°) over a range from 14mT to 3T. This system is composed of an EA300 electromagnet with NMR poles, a MPU-16U ±150A ±70V current source of class 1ppm and a NMR20 Teslameter with a magnetic field controller (FR020).A thermostat chamber can be installed in the air gap (Optionally available on 50mm and 70mm gap poles).
-
Product
Field Strength Meters
FIM-22 And FIM-41
-
The Models FIM-22 and FIM-41 are portable field strength meters designed to provide precise, direct measurements of electro-magnetic fields in the 200 kHz to 5.0 MHz spectrum. These units include a receiver, integral shielded loop antenna, precision attenuator, internal calibration source, and battery power supply. With calibration accuracy traceable to the National Institute of Standards and Technology, the FIM-22 and FIM-41 meet the most exacting requirements of government and industry. Their hinged covers, on the rugged drawn aluminum cases, contain a loop antenna. Opening the cover to a vertical position connects the antenna terminals to the receiver via maintenance-free gold-plated contacts. An interlock switch prevents inadvertent battery discharge when the cover is closed.
-
-
Product
Magnetic Connectors
-
C.C.P. Contact Probes Co., LTD.
Easy to use and extremely smart. CCP has long-standing experience for magnet connectors
-
Product
Magnetizer
-
MAGSYS magnetizers allow the magnetization, adjustment and also the demagnetization of isotropic and anisotropic magnetic materials of different sizes. In particular, all highly coercive magnetic materials, such as Sm2Co17 or plastic-bonded NdFeB magnets, can be magnetized easily and with short cycle times. In addition to raw magnets, e.g. directly after production, complete workpieces with magnets already installed can also be magnetized.
-
Product
Magnetic Field Logger Sensor
NUL-214
-
This is a very sensitive magnetic fields sensor. It can measure a very low level of magnetic fields such as the magnetic field of Earth.The logger sensor measures the magnetic fields in milli Tesla (mT).
-
Product
Complete Field Meter Site Testing Solution
7 Series
-
We raised the industry standard by introducing the PowerMaster 7 Series as a true 3-phase analyzing reference standard with internal 3-phase current and voltage source capability. The innovative design of the PowerMaster® 7 Series allows utilities to fully test a metering installation with one piece of equipment. Customer load meter testing, phantom load meter testing, CT burden and ratio testing, CT de-magnetization, PT ratio testing, and transducer testing can all be performed with one solution. In addition, vector diagrams, voltage and current waveforms, and harmonics data up to the 100th harmonic can all be analyzed to complete a true wiring verification.
-
Product
Magnet Tester
MP
-
Computer aided measuring desk for automatic measurement of hysteresis loop of hard magnetic materials. Use pole pieces with integrated measuring coils, or J-compensated surrounding coils.
-
Product
Field Management
-
EAG offers field-to-final report project management for studies to demonstrate human and environmental safety. As on-site study directors, our Field Managers bring decades of study design, protocol development, analytical oversight, and GLP/QA compliance expertise across a variety of field management study types. In addition, EAG’s access to a broad network of field sites across the United States and Canada ensures that we can deliver the test system, soil characteristics and geography necessary for just about any regulatory need.
-
-
Product
Magnet Testing
3MTS – Triple Axis Handheld Teslameter
-
3MTS is a handy 3-axis teslameter, which was developed in cooperation between Matesy GmbH and SENIS AG.
-
Product
Field Balancing Software
DS-0227A
-
The trouble of rotation machinery is caused most frequently by unbalanced phenomenon of rotating shaft. However, balancing correction on-site is not easy because the conventional vector calculation method with drawing needs quite some time.
-
-
Product
3-axis Magnetic field Sensor
FLC3-70
-
Compact, low-power, 3-axis fluxgate magnetometer for the measurement of weak magnetic field down to nanoteslas. Due to its rugged design and extended operating temperature range suited for automotive and aerospace applications and for deep drilling tools.
-
Product
Field Current Regulator
-
We are counted amongst the leading names in the industry, offering wide range of Field Current Regulator. Our entire product line ensures easy operations and is performance based. Field Current Regulator are quality tested and are delivered in standard configurations. Our entire product range has high strength and is delivered at most affordable rates.
-
Product
Field Strength Meter
FIM-72A UHF
-
The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range of either 20 dB or 60 dB. A dc analog voltage, proportional to meter indication, is provided for driving a chart recorder or similar device. A leveled output from the calibrating generator is available for measuring cable insertion loss, filter response, amplifier gain, VSWR, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
Product
PRECISION MAGNETICS ANALYZER
3260B SERIES
-
At the design stage of component development it is vitally important to understand how the component performs under different operating conditions. This might include operation at diverse frequencies, AC drive levels or DC bias currents.
-
Product
Magnetic Field Visualization
cmos-magview
-
The devices of the cmos-magview family are high-resolution and precise measuring and visualization systems for magnetic materials, assemblies and surfaces. Pole distances or other geometric information can be measured down to the µm range.
-
Product
Field Testing Services
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT offers three levels of testing services both domestically in the US and globally. With the best quality products, complete PD solutions, rich on-site testing experience, experienced partial discharge experts and field engineers, PMDT also provides PDExpert Services -- professional on-site partial discharge detection and location services to help the customers find the potential risks, evaluate the operating status of the electrical assets, and deliver complete and final problem solutions.
-
Product
Reference Magnet
-
Reference magnets generate a homogeneous magnetic field in an air gap. They are mainly used to calibrate hall probes for their full scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using reference magnets.
-
Product
Magnetic Research System
MagRS
-
The MagRS base system comes with a 4 or 7 in magnet, with additional options to customize the system for your experimental needs. Choose to add VSM capability, temperature option accessories, or optical access. MagRS comes standard with ExactGAP magnet pole gap indexing and GlideLOCK precision sample positioning.
-
Product
Universal Field Calibrater
UFC 45-B
-
Model UFC-45-B field calibrater is widely used calibration tool in process industry for last 15 years. Functionally it is designed to tackle most common trouble-shooting during commissioning and routine maintenance. Model UFC-45-B is truly hand held calibration instrument purposely limited functionally to simplify its use. With all its features UFC-45-B battery operated field calibrator is an essential tool in a service engineers kit.
-
Product
Field Analyzers
-
Active broadband isotropic antenna combined with portable USB powered spectrum analyzer. OFA-S/SE antenna has frequency response independent of antenna or electric field orientation. It offers broad dynamic range for the variety of RF regulatory, safety, EMC, wireless and telecommunications applications. Spectrum analyzer SA-S displays the frequencies and field strength of selected signals, allowing all results to be viewed and stored on PC.
-
Product
Magnetic Flaw Detector
CJX-A
-
multifunctional magnetic flaw detector absorbed the advantages of similar products at home and abroad. With small size, light weight, easy operation, multifunction in one unit. The detector can equip A, D, O three types of probes to realize the functions of magnetic clamp detection, electromagnetic yoke detection, ring detection. It is the necessary detector to do flaw testing, quality control, safety check, life evaluation in the fields of petrol, chemicals, metallurgy, shipbuilding, aviation, railway etc..
-
Product
Magnet Tester
-
The Magnet Tester invented by JUNG locates magnetic fields and notify it with its integrated lamp: compact, simple and fast!Easily check switch conditions with zero set-up time and no need to halt operations. The magnetic field test stylus is an indispensable tool for countless companies and toolboxes. Its light-function also makes it as an ideal flashlight.
