EMI
unintentional signal interference originating within or outside the system or circuit. Also known as: Electromagnetic Interference
See Also: Interference, Interference Generators, EMI Receivers, RFI, EMC, LISN
-
Product
ITA, G20x, 6.75" Series Adapters, 28 Module, EMI, 2"
410120253
ITA
ITA, G20x, 6.75" Series Adapters, 28 Module, EMI, 2"
-
Product
ITA, i2 MX, EMI, High Speed, XL Backshell (XL Bend Radius and Cable Exit)
410130133
ITA
This model i2 MX includes VTAC high speed rail inserts making it compatible with VPC wired SIM ITA inserts. The XL-size backshell allows for a greater cable bend radius and large cable exit which accommodates larger, high speed cables. The max cable bundle eff diameter= 1.67".
-
Product
Power Line Meter
-
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
Product
Emissions Test System
PC-114
-
Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.
-
Product
EMI Test Receiver
ESL
Receiver
The R&S®ESL EMI test receiver combines two instruments in one, measuring EMC disturbances in accordance with the relevant standards and also serving as a full-featured spectrum analyzer for diverse lab applications. The combination of very good RF characteristics and all of the important functions needed for fast, precise measurement and evaluation of the EMC of a device under test in accordance with commercial standards is unmatched in this instrument class.
-
Product
EMC Testing
-
EMI is emitted radiation and its effects – a phenomenon. EMC is a device’s ability to limit the levels of unintentionally emitted EMI (that can harm other devices) and also a device’s ability to operate normally when subjected to EMI. Therefore, EMC testing seeks to ensure that a product possesses the characteristic of Electromagnetic Compatibility (EMC): the ability to limit creation of EMI (Electromagnetic interference) and the ability to operate properly when subjected to EMI. Stated differently, EMC testing measures the level of EMI control found in a device, and therefore helps to ensure that unwanted effects are prevented.
-
Product
EMC/EMI
-
American Environments Co., Inc.
ElectroMagnetic Compatibility/ElectroMagnetic Interference
-
Product
Electromagnetic Interference Test
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Electromagnetic Compatibility (EMC) Testing Capabilities
-
Electromagnetic Compatibility testing analyzes the ability of electronic devices to operate as anticipated when in proximity to other electronic devices or in the presence of electromagnetic disturbances that interfere with their intended operation.We help you ensure EMC compliance and attain the needed EMC certifications by assisting you in maximizing accuracy, reducing testing cycles, and getting your products to market faster — from design conception to end-product completion even against the most demanding electromagnetic regulations.We understand that time to market is everything which is why our global testing capabilities and custom testing solutions utilize the latest technology and automation software, helping you meet demanding time-to-market needs. Our streamlined testing process brings your product from development to end use efficiently in accordance with government, regulatory, military, or industry standards based on your compliance needs.
-
Product
Antenna Impedance Converter
-
The low noise impedance matching equipment has a high impedance input with minimized capacity. With the 50 Ω output it can be used with common EMI receivers or spectrum analyzers to measure the emissions received by an antenna on a vehicle.
-
Product
Fibre Network Providers for High Speed and Low Latency Network Infrastructure
-
PBE Group is a fibre network provider that delivers a vast array of integrated tunnelling and mining projects globally and offers custom fiber-based solutions that are reliable, robust and easy to use.Rebroadcasting systems (LTE, FM, TETRA, P25, etc), video monitoring and real time machine control systems can demand high bandwidth and low latency for operation. PBE offers a wide range of fiber-based solutions that can satisfy these requirements. PBE provides Ethernet over Fiber Network and RF over Fiber Network systems in mines and tunnels.Fiber network has a number of advantages:- Covers greater distances with less loss- Support high bandwidth- Immunity to EMI and RF Interference- Support different topologies (Star, Ring, Tree, etc.)- Flexible design and deployment- Flat frequency response and wide frequency ranges- Easy to implement redundant network
-
Product
OEM 1-Channel Fiber Optic Signal Conditioner PCB Module
FOTEMP1-OEM-MNT
-
The FOTEMP1-OEM-MNT is a small form factor PCB interface module designed for low cost insertion of high precision GaAs-based fiber optic temperature sensor technology into OEM applications where common electrical temperature sensors and thermocouples cannot be used. The OEM interface product is compatible with all TS series fiber optic temperature probes. The sensors are entirely non-metallic and electrically passive, providing immunity to EMI, RFI, MR, microwaves and radiation is required.
-
Product
EMI Shielding Effectiveness Testing
-
Eurofins E&E North America can easily develop sound engineering measurement techniques to quantify the SE of your product. Our process involves creating detailed SE Test Plans used to insure accurate and repeatable test results.Eurofins a has years of experience to assure our customers that the evaluation reflects the electrical attenuation performance of the material. Often times, our test report becomes supporting documentation for our customer’s end-user contractual requirement, where Independent Test Laboratory results verify the electrical performance of the material being tested.
-
Product
Magnetic Shielding Cabinet for EMI Testing
SDR-2000B
-
Cabinet Shell 2mm galvanized cold-rolled steel sheetCabinet Door 0.9*1.7m(L*W) 0.6*0.6mCabinet Window 0.3*0.3*0.025m(L*W*T) with 4mm hole N/APower Supply Filter 30A/220V 30A/220VInternet Line Filter RJ-45 N/ACabinet Inside Decoration PVC ceiling, PVC plastic steel wall, 10mm wooden + 2mm galvanized steel sheet floorCabinet Inside Size 2*1.2*1.8m 0.8*0.8*0.8mAfter Packing Size 2.2*2.3*2.3m 1*1.1*1.2mAfter Packing Weight 800kg 200kgWorking With EMI-9KA/EMI-9KB EMI-9KA/EMI-9KB, PC, Testing load, and operator inside Testing load is inside to connect with EMI-9KA/EMI-9KB via BNC
-
Product
EMI Test Receiver
ESRP
Receiver
The R&S®ESRP EMI test receiver has been designed for diagnostic measurements during development and for precompliance measurements to prepare products for final certification testing. It measures electromagnetic disturbances in the 10 Hz to 7 GHz frequency range, using either conventional stepped frequency scans or FFT based time domain scans to significantly speed up measurements.
-
Product
EMC Chambers
-
A specialized, shielded room designed to test electronic devices for radiated and conducted electromagnetic interference (EMI).
-
Product
IC & Transformer
-
Mornsun Guangzhou Science & Technology
MORNSUN launched the self-designed electronic integrated circuits according to the different product lines, types of the integrated circuit include AC/DC power supply control ICs, DC/DC power supply control ICs, interface ICs, start-up ICs, contactor power saving controller ICs and digital isolator ICs. MORNSUN IC chip can be widely used in industrial equipment, process control, data acquisition system, building automation, smart meter, etc. Adopting MORNSUN's AC/DC transformers and DC/DC transformers, with the use of its control ICs, can achieve wide voltage input flyback power supply design with multiple protection functions and superior EMI performance. We hope that those power transformers along with the integrated circuits & chips electronics can be an ideal fit for your application needs.
-
Product
120W to 150W - Single Output
CUS150M Series
-
*150W Convection rating (/U version)*ITE and Medical Certifications (2 x MOPP)*Class B Conducted and Radiated EMI*Suitable for Class I and II installations*Compact 2 x 4 x 1.24" footprint*Suitable for BF Rated Equipment*Operation up to 85°C Ambient
-
Product
Ground Pro Meter
-
Verifies Critical Grounding Parameters of a FacilityMeasures AC voltage, DC voltage, EMI voltage and AC impedanceProvides Accurate Measurements of Ground Impedance on a Working ToolMeets ANSI/ESD S20.20 requirements for AC impedanceIdentifies Potential EOS Generators
-
Product
Power Supplies
CF-480B
-
The CF-series power supply is built with high-quality components for extra long life and maximum system performance along with heavy duty transformers supporting high-end systems. This fanless power supply has a built-in EMI filter for a true no-noise design. The aluminum chassis is built for maximum heat relief to keep the system cool. Combined with a great ventilated structure, you’ll never need a fan. This is a true silent structure that powers your system at 480 watts efficiency.
-
Product
Spectrum Analyzers
DSA700 Series
-
Entry level spectrum analyzers for education, IoT, hobby, and radio applications 500 MHz and 1 GHz models with option for Seamless Signal Capture, EMI, and more
-
Product
RF Shielded Box
LTL A4001
-
Liveon Technolabs LTL A4001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL A4001 RF shielded test enclosure can comfortably house the intermediate device on test. LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
ITA, G10x, 15 Module, Removable Backshell, Keying Feature
410104773
ITA
The adaptable G10x ITA integrates a wide variety of I/O options in various module configurations that allow engagement of up to 3,200 signal contacts. The G10x ITA has a removable backshell that also reduces electromagnetic interference.
-
Product
ITA, i2 MX, 2 QP Modules, Crimp, EMI Backshell (includes front protective cover)
410130202
ITA
ITA, i2 MX, 2 QP Modules, Crimp, EMI Backshell (includes front protective cover).
-
Product
Drum Core Inductors
-
Drum core inductors are so named as the conductor (round magnet wire) is wound directly onto the ferrite core which is shaped like a drum or spool. The wire is then connected to the core, a plastic base or metal lead frame to form the surface mount termination. Drum core inductors come in unshielded (high saturation current but potentially more EMI) and shielded constructions (lower saturation current but closed magnetic path for lower EMI). The shielded constructions use either a second ferrite core or a magnetic resin epoxy to create the magnetic shield.
-
Product
Resistors
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers a broad line of Resistors that include Chip Resistors, Power, High Power, Fuse, EMI Filters, and Arrays and Networks for all applications.Panasonic Resistors have a wide range of features and specifications including conventional Thick Film Chip Resistors or specialized types like Anti-Sulfur, 0201 to 0805 case sized Chip Resistor Arrays, three different types of Power Resistors, Surface Mount and Leaded EMI Filters and one of the smallest Chip Fuses in the industry.
-
Product
RF Shielded Box
LTL B2001
-
LTL B2001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL B2001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
Receiver, i2 MX, 22 Slot VTAC/SIM Insert, EMI
310130113
Receiver
Receiver, i2 MX, 22 Slot VTAC/SIM Insert, EMI.
-
Product
USB Harmonic Comb Injector
J2150A
-
The USB Harmonic Comb Injector is a fast, easy-to-use, ultra-portable signal generator for interrogating your PDN to identify noise sensitivities. Quickly identify power supply related issues. Multiple modes include time and frequency jitter. Wideband harmonic comb spans 1kHz-1GHz+. Great for clock power supply EMI spectrum testing.
-
Product
200 MS/sec RF/IF Extreme 1/2 ATR Recorder
Talon RTX 2586
-
- Rugged 1/2 ATR MIL-spec chassis for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 18 lb (8 kg)- QuickPac® drive packs allow quick removal of all data storage up to 61 TB via the front panel- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- RF/IF recording with phase coherent 200 MHz 16-bit A/Ds and DDCs- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow GUI, API and Signal Viewer analysis tools- Optional telnet remote connection to recorder
