EMI Filters
mitigate high-frequency noise. Also known as: RFI Filters
See Also: Filters, Filter / Amplifiers, Low Pass Filters, Programmable Filters
-
product
Automated Filter Tester
3140-1
The model 3140 filter tester uses the same aerosol generation technology as the model 8130A respiratory filter tester. It works with Emery oil, DOP, DEHS, paraffin and other oils. Two new generation CPCs simultaneously count upstream and downstream particles. This enables accurate, repeatable and fast measurements, for example a HEPA filter can be tested in less than 15 seconds.
-
product
EMI Test Receiver
KH3938B
Beijing KeHuan Century EMC Technology Co,.LTD
Is a fully automatic radio disturbance test receiver and is the main tool for EMI testing. KH3938B receivers frequency range 9kHz-1GHz, in accordance with: 2010 and GB / T6113.101-2016 development standards designed to meet the requirements of the standard-compatible, can be used to power emission test, Sao conduction disturbance voltage test, radiated disturbance within 1G test. The receiver has the advantages of fast test speed , strong maneuverability, stable performance, and convenient test data processing.
-
product
Dual Channel Variable Filter
4302
The Model 4302 Dual Filter is a high performance, low priced, general purpose filter for use in the laboratory as well as in multiple channel data acquisition applications.
-
product
8-Channel Amplifier and Low-Pass Filter Module
SCS-814
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Gas Filter Correlation Carbon Monoxide Analyzer
Model T300
The Model T300 measures low ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 14 meters. The energy loss through the sample cell is compared with the span reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing extreme sensitivity. All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information, is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
Mid-Range Gas Filter Correlation CO Analyzer
Model N300M
Teledyne Advanced Pollution Instrumentation
The Model N300M is a microprocessor-controlled analyzer used to determine the concentration of carbon monoxide (CO) in a sample gas. The analysis method is based on the Beer-Lambert law.The N300M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure.
-
product
Receiver, G6, 6 Module, EMI
310104344
The G6 Receiver includes a keying feature, locking handle and nickel-plated steel slides that engage up to 1,440 signal contacts in a 6-module configuration- all in a compact and rugged design.This G6 model also includes EMI gasketing for EMI protection.
-
product
ITA, i2 MX, 2 QP Modules, Crimp, EMI Backshell (includes front protective cover)
410130202
ITA, i2 MX, 2 QP Modules, Crimp, EMI Backshell (includes front protective cover).
-
product
Broadcast Filters FM
RFS bandpass filters are primarily used as part of multi-channel combiner facilities but can also be used to eliminate spurious emissions and increase isolation between co-sited services.
-
product
RF Filters
Amphenol Procom has 40 years of experience in developing and producing high quality RF Low- and high-power Filters for professional radio systems, widely used in the Public Safety and Mission Critical radio TETRA networks in Europe. The comprehensive portfolio of Filter products from Amphenol Procom are designed by experienced engineers, and highly used in the HF-, VHF- and UHF radio frequency range.
-
product
Gas Filter Correlation CO Analyzer
Model N300
Teledyne Advanced Pollution Instrumentation
The Model N300 is a microprocessor-controlled analyzer based on the Beer-Lambert law that is used to determine the concentration of carbon monoxide (CO) in a sample gas.The N300 uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb Infrared (IR) light. The analyzer passes the IR light beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure.
-
product
Cell Fractionation Filter
CELLNETTA MZM1 Series
Cell sorters, magnetic beads, and gravity separation are common cell fractionation methods. CELLNETTA uses the micron size differences of cells to enable conventionally difficult high-precision fractionation and simple cell separation using an innovative fractionation filter.
-
product
High Frequency Tunable Bandpass Filters
CTB Series
Tunable Ranges Up To 8 GHz. Bandwidths 1% to 5% of Tuned Center Frequency. Digital Control Offered in Various Inputs, including GPIB (standard), RS-232, RS-422, and USB. Custom Interfaces Available.
-
product
Super-Notch YIG Band-Reject Filters
YIG Tuned BRF patented technology gets closer to the ‘perfect notch'. Leveraging a long heritage of engineering innovation in YIG technologies, Teledyne RF & Microwave has developed a line of YIG Tuned Band-Reject Filters powered by patented new technology that overcomes many long-time design limitations inherent to YIG Band-Reject or “notch” filters. Our new line delivers major advancements and unequalled performance.
-
product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3
The AAF-3 is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier ISA bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
product
Tunable Filters - Digitally Controlled
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning the desired signals while rejecting the interfering signals. The method of tuning can be either mechanical via a tuning knob mounted on the front of the filter, or electro-mechanical via an optional remote digital interface such as GPIB, RS-232, RS-422, BCD, ARC171, ARC234, Ethernet, USB or "Thumbwheel" panel mount.
-
product
8-Channel Amplifier and Low-Pass Filter Module
SCS-819
The SCS-818 and SCS-819 amplifier/filter module provides eight 4-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-818) and 0.5Hz to 70kHz(SCS-819). Each of the SCS-818/SCS-819's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Automatic Battery with Filters with Standard Contactors
BATLVF1200
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralizedcompensation of power factor in low voltage instalations
-
product
Capacitor for AC Filtering
PECA4 (690V)
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines.
-
product
Broadcast Filters VHF DAB
The filters offer a compact and flexible solution for both transmitter mask filtering and digital RF channel combining. The DAB filter range is founded on RFS' world-leading RF combining technology and utilizes a similar platform of components to the company's VHF Band III;digital television combiners. DAB filters can beincorporated within transmitters to provide critical mask filtering of the digital RF signal, in keepingwith global DAB standards. When used as the key components of a balanced DAB combiner, thefilters can achieve both critical transmitter masking and adjacent channel combining simultaneously,eliminating the need for additional filters within the transmitter.
-
product
9 kHz Highpass Filter
TBHPF1-9KHZ
9 kHz Highpass Filter for protection of spectrum analyzer or EMI-receiver RF inputs against high amplitude subharmonics and residual 50 Hz voltage in conducted emission measurement set ups
-
product
Filtered Analog Input Expansion Board
MSXB 048
The MSXB 048 Filtered Analog Input Expansion Board has a four-pole low-pass Butterworth filter on each of its 16 single-ended channels. For DAP applications that require analog filters to take out all above-Nyquist frequencies before signal conversion, it simply replaces the MSXB 037 Analog Input Expansion board. Signal inputs normally connect to the MSXB 048 through a panel-mount DB-37 connector.
-
product
Low-PIM, High-Power Filter Solutions for Monitoring Broadband Emissions
Enables monitoring of PIM to 13 GHz; 100W CW and 1KW peakNear-end monitoring: Carriers rejected -90dB by the notchtravel through the bandpass filter to the low PIM termination.Far-end monitoring: Carriers rejected -90dB by the highpass,IM products passed are monitored by the spectrum analyzer.
-
product
Band Pass Filter
PA72BPF
The PA72BPF daughter board is an additional filter board. It typically contains two selectable differential 3rd order elliptic band pass filters. These filter modules are tailored by Applicos to the customers’ requirements. The filters can be used to filter the output signal of the generator daughter boards to achieve an even better distortion and noise suppression.
-
product
Gas Filters
WITT gas filters enable the finest filtering of impurities in technical gases such as acetylene, argon., oxygen, hydrogen, methane, carbon dioxide, helium, compressed air and ethylene. They thus protect downstream equipment and systems. Some gas filters are also referred to as gas cleaners.
-
product
Ultra-Low Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300U
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300U comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
ITA, i1, EMI Shielded, With Protective Cover
410128102
The i1 EMI has many of the standard features of the i1, in addition to Electro-Magnetic Interference (EMI) protection. The EMI shielding effect on the i1 EMI ITA is provided by the stainless steel fibers in the removable plastic cover and threaded metal coupling adapter.
-
product
High-Pass Filters
is an electronic filter that passes signals with a frequency higher than a certain cutoff frequency and attenuates signals with frequencies lower than the cutoff frequency.
-
product
Rack Module with Standard Contactors without Anti-Harmonic filters
MOD Rack
Lifasa - International Capacitors, SA
The MOD-RACK control units include, in a compact form, all the components necessary for the operation of a step of a standard capacitor bank. MOD-RACK modules are divided into two basic blocks: power block and control block. The two blocks are mounted in a small frame to be installed in an electrical panel.
-
product
ITA, 9050, 50 Module, Double Tier, EMI, with 8" Enclosure
410104580
This 9050 ITA comes with an 8" enclosure for ease of system integration. The ITA is designed to work with the 9050 EMI receiver.
