ATE
ATE systems are used to test semiconductor devices, printed circuit boards, and electronic systems during manufacturing. AI prompted RL created', prevails upon the UUT to demonstrate It's fulfillment of test requirements.
See Also: Automatic Test Equipment, ATS, Functional ATE, Combinational ATE, Semiconductor Test, PXI Switching, PXI Chassis, PXI Matrix, Automated Test Equipment, Automated Test Systems
-
Product
PXI 8 Slot BRIC 300x8 2-pole (10 sub-cards)
40-561A-122-300X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
-
Product
DC Coupled Differential Switching System
BS1553F(X)
-
Universal Switching Corporation
The BS1553F(X) is a modular passive DC coupled differential switching system. It is designed as an automated "patch panel" for interconnecting numerous MIL-STD-1553 devices, cables and hardware, or for routing other differential signals such as '422 clock/data or kelvin ATE measurements. The I/O capacity is scalable from a small 8x8, up to 64x64 in one 5RU unit.
-
Product
PXI Very High Density Multiplexer, 2A, 79-Channel, 2-Pole, Single Channel Mode
40-611B-002
Multiplexer Module
The 40-611B-002 (PXI) and 42-611B-002 (PXIe) modules are 79-Channel 2-Pole multiplexers. A 158-Channel 1-Pole configuration is also available. They use high quality electro-mechanical signal relays allowing switching up to 2 A and voltage up to 300 VDC/240 VAC.They are suitable for signal routing in high channel count ATE and data acquisition systems. Connections are made via a front panel 160-pin DIN 41612 connector.
-
Product
PXI 8 Slot BRIC 322x8 1-Pole Dual Analog Bus (7 sub-cards)
40-560A-121-322X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2 Amp MUX, Dual 16-Channel 1-Pole
40-635-105
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 8 Slot BRIC 242x8 2-pole (11 sub-cards)
40-562A-122-242X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe RF Multiplexer, Dual 6-Channel, Terminated, 8GHz, 50Ω, SMA
42-881B-002
Multiplexer Module
The 40/42-881B has low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the module ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
Product
PXI 4 Slot BRIC 88x4 2-pole (2 sub-cards)
40-562A-022-88X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Very High Density Multiplexer, 5-Channel, 32-Pole
40-675A-002-5/32
Multiplexer Module
The 40-675A-002-5/32 is a 5-channel, 32-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI 8 Slot BRIC 138x16 1-Pole (6 sub-cards)
40-560A-121-138X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2 Amp MUX, Single 64-Channel 1-Pole
40-635-001
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI High Density Multiplexer, 10-Bank, 8-Channel, 2-Pole
40-615A-004
Multiplexer Module
The 40-615A-004 is a 10-bank, 8-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
Redundant Strap down INS ATE Test Station
-
Redundant Strap down Inertial Navigation System (RESINS) checkout test station comprises of cPCI chassis with various functional I/O modules like ADC, DAC, DIO, VFC, Relay matrix, MIL 1553, GPIB, Serial communication interfaces and Custom Built System interface adaptor.
-
Product
PXI High Density Multiplexer, 10-Bank, 16-Channel, 1-Pole
40-615A-003
Multiplexer Module
The 40-615A-003 is a 10-bank, 16-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful here a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
Power Module Tester
-
The Power Module Checkout ATE is developed for testing DC-DC Power modules typically utilized in India's space program. The DC-DC converters are exhaustively tested for all design parameters including supply voltage range, line and load regulation, efficiency, ripple, noise, transient response and so on. Special power sources and loading mechanisms are deployed to enable testing of various types of power modules.
-
Product
PXI 4 Slot BRIC 90x16 1-Pole (6 sub-cards)
40-561A-021-90X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Dual 6 to 1 RF Multiplexer 6GHz 50 Ohm SMA Terminated
40-881-002
Multiplexer Module
The 40-881 is a 50 Ohm 6 to 1 6GHz multiplexer available as a single or dual MUX in one and two PXI slots respectively. The 40-881 exhibits low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the 40-881 ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
Product
DC Power Module 0 To 5 V, 0 To 10 A, 50 W
N6731B
Power Module
The Keysight N6731B, a 50 W basic DC power module, provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power the device under test or ATE system resources, such as fixture control.
-
Product
Semiconductor Products
-
International Testware Corporation
International Testware supports all major ATE models for today's semiconductor products.CredenceAdvantestCaesarHewlett-PackardLTXIMSSchlumbergerAndo...and MANY moreTeradyneMosaidOur Solutions offer:Mixed-SignalEMI ReductionR/FCustom TailoredLow NoiseReliable PerformancePrecise Length MatchingSuperior Impedance ControlCrosstalk "Immunity"Minimal Inductance
-
Product
PXI 4 Slot BRIC 90x16 2-Pole (6 sub-cards)
40-561A-022-90X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Single 46x4 Matrix, 1 Pole Switching
40-524-021
Matrix Switch Module
Medium density PXI dual 46x4, 1-pole matrix - it is also available inreed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Product
PXI MUX 1 Bank of 128 Channel 1 Pole
40-610-022-1/128/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Super Fast Gang Industrial Universal Programmer
48Pro2AP
-
The Dataman 48Pro2AP is a super fast industrial universal programmer with ISP capabilities and USB 2.0 connectivity • Optimised for use in automated handlers and ATE machines • Over 71,000 devices supported with new devices added monthly • Mechanically stable case design with multiple fixing points • ISP capable using the JTAG interface • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Comprehensive 3 years parts and labor warranty • Free life-time software updates
-
Product
Single 12x12 1-Pole High-Density PXI Matrix Module
40-520-102
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 8 Slot BRIC 22x16 2-pole (2 sub-cards)
40-562A-122-22X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 180x16 2-pole (12 sub-cards)
40-561A-122-180X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 12x4 Matrix, 2 Pole Switching
40-510-022
Matrix Switch Module
The 40-510 series of matrix modules feature a wide range of selectable switchingconfigurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signalrouting in ATE and data acquisition systems.Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screenedversion is suitable for switching signals up to 50MHz. Larger matrices may be constructedby Daisy Chaining the common signals from multiple PXI modules.
-
Product
LXI HighDensity 128x16 2A Matrix with BIRST
60-554-024
Matrix Switch Module
A high-density single pole matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
PXI 2A Multiplexer, 8-Bank, 8-Channel 2-Pole
40-614-004
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
