Plugs
A male connector.
-
product
Synchronization Module
ZET 7175
GPS/GLONASS ZET 7175 synchronization module is used for long-distance spaced object timing in major control, monitoring and data collecting systems. For system operation, it is necessary to have a GPS-aerial connected over SMA plug.
-
product
USB-C® Short Channel Rx Precet. Test Fixture
AUT20098
*Easy swap between CC1 and CC2RP & RD Mode: In the older version of the USB-C full breakout board, users had to manually set the jumper with a short pin. But now users can easily swap between the two by just moving the switch.*In the previous version, the soldering joint of Test Fixture Host Fixture 1A gets worn out quickly from repetitive plug and pull. This newly designed fixture is more durable and users can easily replace the worn out SMA connectors with new ones.*DC-in Jack is upgraded to +5V USB C portA boost in user experience as it makes setting up easier.
-
product
Multi-Modular Cable Tester
3PK-NT005N
Multi-modular cable tester is applied to quickly test by auto scanning most of modular cable, USOC 4 / USOC6 / USOC 8 terminating with RJ 45, RJ12, and RJ11 modular plug, wires continuity and miss-wiring.It can be also used for testing the cable is crossed pinning or straight through. Moreover, with the remote terminator, it can be further used in remote testing even the cable has been already installed.
-
product
Cable Assembly, Receiver, 20/26GHz Coaxial, 20", 7 SMA Plugs
540133010153
Cable Assembly, Receiver, 20/26GHz Coaxial, 20", 7 SMA Plugs
-
product
High Temperature Diametral Extensometers (1000 C)
Model 3580
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
VTAC, Patchcord, Receiver, 36", VTAC, CAT6A FTP, To RJ45 PLUG
7-142705694-036
VTAC, Patchcord, Receiver, 36", VTAC, CAT6A FTP, to RJ45 PLUG.
-
product
Circuit Breaker Identifiers
191 CBI
Standard Electric Works Co., Ltd
● 191 CBI is an easy tool to find the circuit breaker or fuse supplying electrical power to an outlet or lighting fixture. Just plug the transmitter into the outlet.● Use the receiver to scan the circuit breaker panel box. An audible tone will be clearly heard when the right circuit breaker is scanned.● The plug of transmitter is changeable. The plug of transmitter could be changed for customers' requirement from different countries.
-
product
USB Modular Oscilloscope, 100 MHz, 2 Analog Channels
U2701A
100 MHz2 analog channelsMore accurate analysis of electronic designs with deep 32 Mpts memory and high 1 GSa/s sample rateSimple USB setup with plug and play capabilityGet the debug power you need with advanced triggering, automatic measurements, math functions including FFTs and moreQuick and easy measurement configuration and acquisition with bundled Keysight Measurement Manager (KMM) softwareDocument results more easily using the high speed USB 2.0 interface
-
product
24 Block Desktop Receiver
VGR24
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250 VAC/5 Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
product
IEC60669 Pendulum Impact Tester
CX-BC2
Shenzhen Chuangxin Instruments Co., Ltd.
This Pendulum Impact Test Device Conforms to the standard GB2099.1, GB16915.1 and IEC60669, IEC60670 standard. To check the impact resistance performance of plug and socket electrical accessory's enclosure.
-
product
Micro Coax, Patchcord, ITA , 72", 50 GHz, Flex 405, to 2.4 MM Plug
7-372105764-072
Micro Coax, Patchcord, ITA , 72", 50 GHz, Flex 405, to 2.4 MM Plug.
-
product
Noid Lights, IAC Test Lights & Ignition Spark Tester Kit
36330
Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes 8 Noid Lights (for checking GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, BOSCH 2 and GM Multec 2; 2 IAC Test Lights (for straight and 90 applications); and Cat. No. 23900, In-line Ignition Spark Checker.
-
product
8.25mm (0.32") Digit Height
DPM 2AS-BL
The DPM 2AS-BL is an ultra-miniature 31/2 digit LCD voltmeter with 8.25mm (0.32") digit height and LED backlighting. It features a negative rail generator which enables the meter to measure a signal referenced to its own power supply GND. The meter plugs directly into a SIL socket or can be snapped into a panel. Connection to the meter is via two rows of pins
-
product
Electrical Testers
CURT electrical testers are perfect for testing a new wiring harness on your vehicle or troubleshooting the existing wiring. Our trailer plug testers are built with LEDs and are available in 4-way, 5-way, 6-way and 7-way. We also offer brake control testers.
-
product
System Amplifiers
N4985A
The Keysight Technologies N4985A series system amplifiers are high performance broadband amplifiers with excellent power and gain from 100 kHz to 50 GHz. The amplifiers are self-contained and plug into standard AC power sources.
-
product
Multi Voltage Glow Plug Tester
4110
Peaceful Thriving Enterprise Co Ltd
*Auto switch off.*With CE Approval.*Voltage supply by 9V battery.*Tester probe/clip is easy to replace.*Rubber coating for tester protection.*Initialization for different testing probe/clip.
-
product
Relay Buddy Adapter Set
190-4
*Expands the testing capability of your Relay Buddy! *3 pack of adapters allows testing of shielded relays, same relays tested by #190 Relay Buddy *Relay adapter plugs into Relay Buddy first *Shielded relay then plugs into the top of the adapter
-
product
Water Leak Detectors
To install the optional cable sensor, simply plug it into the detector. The entire length of cable is an extended sensor. Additional 4 foot cable sensors (sold separately) can be connected to extend the cable and increase water sensing area even more. Note: The cable sensor jack is NOT for plugging in a power adapter. Doing so could damage the detector.**
-
product
I/O Signal Marshalling
We offer you a variety of solutions for I/O signal marshalling in process automation:The flexible VIP I/O marshalling signal marshalling system makes I/O signal marshalling for universal I/O consistent, from the field to the controller. Our Termination Carriers provide you with a Plug and Play solution for standard I/O system signal marshalling enabling you to connect classic DIN rail devices to the standard I/O cards of your automation system.
-
product
50Ω uWave SMA 2.92 Cable Assembly, 40GHz, 1m
40-977-544-1m
50 Ohm uWave SMA 2.92 Plug to uWave SMA 2.92 Plug Cable Assy, 1m Long.
-
product
Rebar
Continuously monitors the coating line process as reinforcing bar runs through the RBRS dual-roller wet sponge electrodes unit. When a holiday is discovered, a red light flashes at the appropriate station on the detector unit for a visual indication, and the unit sends an eletrical output to a plug on the back of the unit. The MSRB signal output plugs drive any 120 Volt AC customer furnished horn, bell, recorder or computer.
-
product
MAX31855 K-Type Thermocouple Arduino Shield
SEN-30004-K03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855K supports a measured temperature range of -270C-1372C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
PXI/PXIe Power Relay Module,5 Amp, 50-Pin SGMC Connectors
40-153-001-HI
The 40/42-153-001-HI is a PXI/PXIe high density power relay module with 50xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
product
6U Mini Chassis
cPCI395
The cPCI395 mini crate series offers hot-swappable, redundant power supplies in 9 slots, compact but modular designed desktop / 19″ chassis. A front-side-plug high performance DC fan is used for cooling with front to rear air flow. One or two redundant operating plug-in 250W cPCI power supplies provide sufficient power for all applications.
-
product
75 Ohm MCX Connectors
Pasternack 75 Ohm MCX connector category includes several part numbers, the majority are RoHS and REACH compliant. 75 Ohm MCX connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These 75 Ohm MCX connectors are built to precise RF and microwave industry specifications. MCX 75 Ohm connectors are available in jack or plug gender with 75 Ohm impedance. 75 Ohm MCX connector products are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm MCX connector designs include crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this MCX connector series for 75 Ohm is in-stock. Not only are they in stock, these MCX 75 Ohm connectors will ship the same day as purchased.
-
product
PCIe
SFF 8639 Gen4 (U.2)
SCHILLER AUTOMATION GmbH & Co. KG
The 8639G4-TPA-PR test adapter or test fixture kit facilitates Source and Sink compliance testing for SFF-Hosts and Devices. These SFF-8639 Gen4 fixtures utilize the multifunctional connector system supporting single/dual port SATA, dual and MultiLink SAS, and/or up to four (4) port PCIe device configurations. The SFF-8639 Gen4 receptacle fixture will accept devices with plug connectors that are in accordance with SFF-8482, SFF-8630, and SFF-8680.
-
product
Acute 2GHz, 34 Channel, TravelLogic Series Protocol & Logic Analyzer With 8Gb Memory
Acute TL3234B+
The TravelLogic Series of Protocol & Logic Analyzers are small enough to fit into your shirt pocket, yet are truly sophisticated logic analyzers, capable of 2 GHz timing analysis, or 200 MHz state analysis, with up to 8 Gb total stackable memory for the 34 channels. They plug into a PC or Laptop USB port making them ideal for the field service technician or engineer, hopping from PC to PC, or taking with them for diagnosis on the road. Also remember that with USB, no additional power supply is needed.
-
product
PCIe Remote Control Interface
51-924-001
The kit is supplied with this PCIe card which can plug into any PC PCIe slot, a PXI module for insertion into Slot 1 of a PXI chassis and 3m lead to connect the two parts together. The interface uses a single lane PCIe connection from the PC to provide a software transparent link from the PC PCIe backplane to the PXI backplane. The supplied 3m shielded lead ensures the system has robust operation and an adequate separation distance between the PC and the PXI chassis.
-
product
Breakout Boards
D Series Boards
D Series Breakout Boards are open designs that provide signal access when troubleshooting. Signal connections are accomplished by inserting or removing Mini-Jumper plugs. All normal and high density D type connectors are available. Current carry capability is from 2.25A to 5.3A. Normal Density D Type: 9, 15, 25, 37 and 50 positionsHigh Density D Type: 15, 26, 44, 62, 78 and 104 positions
-
product
Mini Back Probes/Wire Piercers
618
*Great for backprobing weather pack style connectors used with numerous automotive sensors *Also very handy for piercing and tapping readings on smaller gauge wires - using the included probe adapters *Works with most Test Lead Kits in the field - with standard 4mm banana plug test lead *Set includes four probes - red, black, green, yellow Test probes 21 mm length
