Plugs
A male connector.
-
product
75 Ohm MCX Connectors
Pasternack 75 Ohm MCX connector category includes several part numbers, the majority are RoHS and REACH compliant. 75 Ohm MCX connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These 75 Ohm MCX connectors are built to precise RF and microwave industry specifications. MCX 75 Ohm connectors are available in jack or plug gender with 75 Ohm impedance. 75 Ohm MCX connector products are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm MCX connector designs include crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this MCX connector series for 75 Ohm is in-stock. Not only are they in stock, these MCX 75 Ohm connectors will ship the same day as purchased.
-
product
Thru-Hole 0.040 [1.02] Female DIP Strip
Series F40
Thru-Hole .040 [1.02] Female DIP Strips. This female DIP strip is used in conjunction with Aries Shorting Plug SP200, available separately, for your programming needs.
-
product
Handyscope TP450-250XM-W5
TP450-250XM-W5
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
product
Long Gauge Length Axial Extensometers
Model 3542L
Jinan Testing Equipment IE Corporation
The dual flexure design makes the 3542L very rugged and insensitive to vibrations. These extensometers are designed for testing a wide range of materials including metals, plastics, composites and ceramics. Epsilon’s Model 3543 is recommended for applications requiring long gauge lengths and larger measuring ranges.The Model 3542L comes standard with Epsilon’s quick attach kit, making it easy to mount the extensometer on the test specimen. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The 3542L extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Impact Test Apparatus
IT-50
Impact test is an essential physical test prescribed in many standards to test samples for mechanical shock. It is designed to perform such tests. The test is carried out to ensure that the test items have adequate mechanical strength to withstand the stresses and rough handling imposed during installation and use. It is adapted to test various types of electrical accessories such as switches, sockets, plugs, starter seats and other electrical appliances.
-
product
SHB12X-H3X24, Male InfiniBand to Differential Flying Leads, Shielded LVDS Cable, 1.5 m
196236-1R5
72-Pin, Female Flying Leads to 48-Pin, Male InfiniBand, 100 Ohm, Shielded LVDS Cable - The SHB12X-H3X24 LVDS Cable connects the 12X InfiniBand connector on PXIe-656x LVDS digital instruments or some NI 658x LVDS Adapter Modules for FlexRIO directly to individual header pins. This cable is intended for use with a custom breakout fixture. The flying-lead cable has three signals per grouping for positive, negative, and ground pin connections designed to plug directly into any 0.1 in. header connector. It is a shielded, 100 ohm cable.
-
product
Pulsar 4 Channel Interface
Pulsar-4 7Z01201
Ophir’s 4 channel Pulsar interface turns your PC or laptop into a full fledged Ophir multi-channel laser power/energy meter. Just install the software, plug the laser measurement sensor into the Pulsar and the USB cable from the Pulsar to the PC USB port. With the Pulsar-4, you can connect up to 4 laser measurement sensors to each module, monitor each pulse at up to 25 kHz and utilize external trigger.
-
product
Multi-Modular Cable Tester
3PK-NT005N
Multi-modular cable tester is applied to quickly test by auto scanning most of modular cable, USOC 4 / USOC6 / USOC 8 terminating with RJ 45, RJ12, and RJ11 modular plug, wires continuity and miss-wiring.It can be also used for testing the cable is crossed pinning or straight through. Moreover, with the remote terminator, it can be further used in remote testing even the cable has been already installed.
-
product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-50
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
product
AdvancedTCA Shelf Manager ShMM700, 280 mm Board
ShMM-700
The 3rd generation Elma ATCA Shelf Manager incorporates bussed IPMB signals. Dual SHMMs can be plugged into slot 0 of an Elma chassis, without taking up any of the 14-slots.
-
product
cDAQ-9179, 14‑Slot, USB 3.0 CompactDAQ Chassis
783597-01
14‑Slot, USB 3.0 CompactDAQ Chassis - The cDAQ‑9179 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements with the higher performance data streaming of USB 3.0. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9179 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
product
Fusion Bonded Cable Jumpers
Series 152FB
Fusion Bonded Cable Jumpers. Aries Series 152FB Fusion Bonded Cable Jumpers are flexible...plug them directly into PC boards or sockets. Stranded wire conductors are fusion bonded with an overcoat of tin for easy soldering or socketing. Each jumper is shipped with protective tabs on both ends for maintaining proper conductor spacing.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
PCB Adapters - TriPaddle
TriPaddle signal technology adapted to a PCB with a variety of standard connector options. Allows for easy PCB integration with an interface while also offering wiring convenience. Offers "plug and play" functionality between module and instrumentation.
-
product
Terahertz Spectrometers
Due to its non-invasive and non-ionizing properties, terahertz (THz) radiation is unparalleled in its sensing capabilities. Based on state-of-the-art research results, HÜBNER Photonics division developed innovative and highly compact plug & play systems – allowing contact-free detection, characterization and analysis as well as hyperspectral imaging of materials by THz spectroscopy within a few seconds.
-
product
Electronic Compact Pressure Switch (Pallect Pressure Switch)
PPE
mm.A compact trimmer setting type, three types of piping connections (R1/8, Φ6 plug, Φ6 one-touch fitting) and a dustproof/waterproof structure allow for flexible use.
-
product
CompactPCI/PlusIO/Serial
ADLINK provides a complete line of 3U and 6U CompactPCI platform and along with a diverse line of plug in boards and these CompactPCI products provide the most cost-effective high performance platforms for telecommunications, military , industrial automation.
-
product
3 Position Plug Socket Switch Life Tester
CZKS-3
It is designed according to terms and conditions of IEC60884-1, IEC60669-1, GB2099.1-2008 and GB16915.1-2003, for life test of plug and socket and switch products of household and similar use appliances.The device can connect with matched load cabinet, in order to conduct a test of electrical life, normal operation and breaking capacity. The equipment provides some clamps. It can test plug and socket production, wall switch, rocker switch, dial plate switch and button switch.
-
product
USB Network Gate
With USB Network Gate you will never experience any issues accessing and using the USB devices that are plugged into remote computers. You can work with those devices as if they were physically connected to your local machine. All that is needed to do for that is install USB over Network Connector on the computer with USB device physically attached (server) and on the computer where you want to use this device (client). USB over IP Connector will do all the rest. No additional hardware needed! BTW you can choose whether Mac, Linux or Windows machine will be a client or a server.
-
product
XL Release
Plug in everything you are using in a snap - CI, provisioning, change management, ALM, or test tools, middleware or cloud platforms, old legacy systems, or microservices and containers.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
PXI/PXIe Power Relay Module,5 Amp, 37-pin D-type Connector
40-153-104-HI
The 40/42-153-104-HI is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 37-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
product
AC Power Sources
RS Series
AMETEK Programmable Power, Inc.
The RS Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the RS series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the RS unit to its designated location (using included casters), plug it in, and the RS series is ready to work for you.
-
product
Cable Assembly, Receiver, TriPaddle, 36", 6 and 2 Position Mini-Combicon Plugs
540162010201
Cable Assembly, Receiver, TriPaddle, 36", 6 and 2 Position Mini-Combicon Plugs
-
product
Bi-Axial or Axial Averaging Extensometers
Model 3560
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parallel multiple flexure design makes these units very durable.The Model 3560AVG reads axial strain only as a single averaged output. It may also be supplied with two independent outputs, one measurement from each side of the specimen. This set-up is most commonly required when an indication of specimen bending is desired. The second version, the Model 3560BIA, includes both the averaged axial strain and the transverse strain. Again, this may also be configured as dual independent axial readings, which results in a three channel extensometer.The Model 3560 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Data Logger for Temperature and Humidity
DSR-THEXT
Using external compact probe especially for HVAC application to measure and log temperature and humidity data inside pipes with minimal invasion Support screen and audible alarm Original fittings for sensor connection, ensures 100,000 plugs Suitable for HVAC, agriculture research, plants and animal growth monitoring and other applications
-
product
Bus Analyzer / Exerciser
VME850P0
The VME850P0 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P0 connector. This module allows the user to monitor and stimulate the A, B, C, D and E rows of the 95 pin P0 connector. Although the VME850P0 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P0 connector must be less then 5V in order to prevent damage of the analyzer.
-
product
Tow Doctor™ Vehicle Side Test Unit
50918
Hopkins Manufacturing Corporation
Specifically designed so that one person can make sure a vehicle has been wired properly and all functions are working. Plug the Tow Doctor™ into the vehicle towing connector, carry the display unit to the cab of vehicle and cycle through the vehicle lighting functions. Includes 7 Blade, 6 Round and 4 Flat adapters and durable carrying case.
-
product
Cable Assembly, Receiver, TriPaddle/Mini Coax, 36", 4 SMA Plugs, And 19 Pin ML HDMI
540364010210
Cable Assembly, Receiver, TriPaddle/Mini Coax, 36", 4 SMA Plugs, And 19 Pin ML HDMI.
-
product
Thermopile Power Sensors
Thermopile optical power sensors are based on thermocouples. A thermocouple consists of two dissimilar metals connected in series. To detect radiation, one metal junction is typically blackened to absorb the radiation. The temperature rise of this junction with respect to another non-irradiated junction generates a voltage. Our thermopile power sensors offer broadband, spectrally flat response, and calibrated plug and play operation with our optical power meters.
