Vibration Isolation
Control of unwanted vibration so that its adverse effects are kept within acceptable limits. (www.sdp-si.com)
See Also: Vibration Test, Tables
-
Product
128 Channel Isolated Digital Input / Interrupt Module
DP-VXI-3117
-
DP VXI 3117 provides 128 isolated channel digital inputs for sensing DC levels and edge transitions of upto 48VDC. The input level selection for 5 (TTL / CMOS compatible), 12, 24 or 48V is made through on-board jumper selection. The debounce feature is programmable for a period of 2msec to 2147 sec. in binary increments. Channel groups 1 to 32, 33 to 64, 65 to 96 and 97 to 128 can each have a unique programmed debounce period, provided the ratio of clock period between groups does not exceed 32,768.
-
Product
12-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-8
-
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
4-Port Isolated RS-232/422/485 With IRIG B Card
ECU-P1624D
-
industrial communication module designed for high-reliability, time-synchronized serial data transmission. It supports four software-configurable RS-232/422/485 ports, often including isolation for interference protection, alongside an IRIG-B time synchronization input, commonly used in substation automation.
-
Product
PXI 5A Mux 1-Bank 48-Ch Isolated COM + Ind Isolation
40-651-111
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Vibration Analyzer
DigivibeMX® M30
-
DigivibeMX® M30 System is the Vibration Analyzer, Dynamic Balancer and Data Collector with more functions in the market. From simple Vibration analysis to complex 3D ODS vibration simulations, DigivibeMX® M30 is the best tool for predictive analysis and diagnosis for your machinery.
-
Product
Isolated Relay I/O Card
mPCIe-IIRO-8
-
The mPCIe-IIRO-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
Vibration Monitoring
-
From milling machines to pumps to wind turbines – wherever the condition of machines and systems needs to be monitored, Pepperl+Fuchs vibration monitoring products help prevent unplanned downtime and ensure personal and system protection.
-
Product
Detect, Trend, And Analyze Ultrasound And Vibration
SDT340
-
SDT340, together with UAS4.0, is a cloud connected condition monitoring solution. Detect, trend, and analyze asset health by viewing the ultrasound and vibration time signal and spectrum directly on the SDT340’s color display.
-
Product
Vibrating Sample Magnetometer
VSM
-
The Cryogenic Vibrating Sample Magnetometer (VSM) is designed for measurement of the DC magnetic moment of a sample with a noise floor sensitivity of 10-6 and at 10 seconds integration time.
-
Product
4-Channel Vibration Analyzer Kit
HD2030.K1
-
The HD2030 is a portable vibration analyzer able to perform spectral and statistical analysis. The instrument can supply all the measurement parameters required by the current normative concerning the operators protection from the risk connected with the vibrations and is able to measure in hand-arm and whole body modes. It is also possible to evaluate the annoyance on persons due to vibration in buildings.
-
Product
Vibration Test System
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Vibration Test System is a simulation of the various environments encountered in the manufacturing, assembly, transportation and use phases of execution. It is primarily used to identify the ability of a product to withstand environmental vibrations.
-
Product
16 Channel Isolated Analog Output Module
DP-cPCI-2502
-
The DP-cPCI-2502 is a 16 channel analog output module organized in four groups of 4 channels each. Each group is isolated with respect to each other and with respect to the system using optical isolators and DC-DC converters. Each output channel is driven by a 16 bit resolution precision DAC. The input digital data is converted to analog signals of ±10V range. The digital data for the DACs is written from the cPCI interface via two banks of latches enabling a double buffered output scheme.
-
Product
32-CH Isolated DIO Card
LPCIe-7230
Analog Input Module
ADLINK LPCIe-7230 is 32-CH isolated input and/or card. It provides a 2,500 C optical isolation protection. Two wide input range of the LPCIe-7230 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The LPCIe-7230 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automations applications. The LPCIe-7230 also provides two interrupt sources on digital input channels, which are easily user configurable.
-
Product
PXI-8433, 4-Port, Isolated, RS485/RS422 PXI Serial Interface Module
779539-01
Serial Interface
4-Port, Isolated, RS485/RS422 PXI Serial Interface Module—The PXI‑8433/4 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Isolation Probe
SE-6000/6010
-
Performs waveform measurements with high resolutions and in safe manner under high voltage environment in systems that isolate Input/output terminals through optical insulation
-
Product
Isolated RS-485
-
Renesas' isolated RS-485 differential bus transceivers provide bidirectional data communication for Industrial Internet of Things (IIoT) networks.
-
Product
Keysight 40/80 Channel Optically Isolated FET Multiplexer for 34980A
34925A
Multiplexer Module
The Keysight 34925A module for the 34980A Multifunction Switch/Measure Unit is a high speed multiplexer that uses long-life, solid-state relays. The high-speed FET relays scan up to 1000 channels-per-second. Use this module for high-volume automated test applications that need high-speed, long-life relays.
-
Product
Fence Vibration Sensor
ENVIROMUX-FENCE1
-
Detects when individuals climb over or cut through chain link or wire mesh fences. Advanced built-in signal processor prevents false alarms. Four sensitivity settings to tune each sensor to a particular fence section and intrusion type. Two open-collector outputs – alarm and power failure. UV resistant case and epoxy sealed electronics provides maximum resistance to harsh environments. Rated NEMA 4X and UL94 5V. Use individually or chain units with each ranging from 40 to 60 feet away. Includes mounting brackets for installing the sensor to fence fabric. Screw terminals. Operating temperature: -4 to 131°F (-20 to 55°C). Operating voltage: 9-15V DC.
-
Product
vibration test system
-
Labtone Test Equipment Co., LTD
Labtone EV series of electrodynamic shaker vibration test System simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications.Labtone EV series of electromagnetic vibration testing system simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications. In the laboratory, with the aid of vibration testing system, simulations of reproduction of sinusoidal, random, resonant search and dwell, classical shock and road models, etc. can be achieved. It is essential for product quality assurance, new product research and development.Labtone EV series of electromagnetic vibration testing system is specially designed to meet the need for long time operation. Vertical and horizontal vibrations can be achieved by the installation of vibration resistant base. The standard platform is equipped with high efficiency airbag shock isolation device, so that the vibration transmitted to the building can be minimized. There is no need for additional foundation in most of the cases.A complete set of vibration testing system is composed of shaker, power amplifier and vibration measuring control system, in accordance with the relevant national and international standards (such as: MIL-STD, DIN, ISO, ASTM, IEC, ISTA, GB, GJB, JIS, BS, etc.) to provide technical support for establishing product quality inspection.
-
Product
High Selector Isolating Transmitter
Model TWH
-
Kusam Electrical Industries Limited
• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• High Accuracy 0.1% RO at 23 ° C ± 5 °C• Input / Output User Selectable• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 1.5KV/Min, between Input / Output / Power)
-
Product
Isolated USB Digital I/O Modules (OEM Version Available)
USB-7230/7250
Data Acquisition Module
The USB-7230/7250 USB-based digital I/O modules feature high voltage on/off control and monitoring, and isolation voltage supported up to 2500VRMS. The USB-7230 provides 32-CH isolated digital I/O and 2-CH frequency/event counters. The USB-7250 provides 8-CH relay output (4 form C and 4 form A), 8-CH isolated DI, and 2-CH frequency/event counters. The USB-powered USB-7230/7250 features removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
-
Product
Vibration Test Chamber
Series TV / CV
-
During transportation, or when used under heavy mechanical loads your products vibrations or oscillations can be exposed, which may negatively affect the quality and longevity. To simulate these effects can be personalized with the modular standardized versions of the corresponding CTS installations, the requirements such as vertical and horizontal meet vibration and this in conjunction with very high rates of temperature change.
-
Product
Isolated Input Relay Card With COS
PCIe-IIRO-16
-
This product is a x1 lane PCIe isolated digital input and relay output board with Change of State (COS) detection capabilities.
-
Product
Vibrating Forks / Rods
-
We provide a highly diversified offering of level switches and sensors, ranging from simple single and multi-level liquid level switches to these more advanced sensor technologies used in the measurement of liquids and solids across more rugged media applications. These devices come in numerous sizes and materials, with our more advanced vibrating forks and rods providing numerous electrical settings, fittings, and various enclosures for more hazardous environments.
-
Product
8-CH Isolated Digital Input Module
ND-6052
Data Acquisition Module
- Channels: 8 DI. 6 fully independent isolated; 2 isolated with common ground- Isolated Voltage: 5000 VRMS- Programmable input polarity
-
Product
Air Bearing Vibration Exciter
CAL25HF
-
The Model CAL25HF offers transverse performance over traditional flexural-based calibration exciters, with operation over an operating bandwidth of 3 Hz to 20 kHz. It is available as either a stand-alone unit, or as part of a larger automated calibration test system.
-
Product
Sound and Vibration Real-Time Analysis System
DS-3200 series
-
The DS-3000 series Data Station is a PC-based FFT Analyzer with high functions and high performance. This new FFT Analyzer has two times or more of real-time analysis capability compared to the existing model the DS-2000 series, having the high-speed calculation performance, reliability, and user-friendliness based on our accumulated experience.
-
Product
16-bit, 200KHz, 4SE/2DIFF Isolated Analog Input Board
APCI-3016-4
-
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
Product
General Purpose Vibration Sensors
AC104
-
Multi-Purpose Accelerometer, Side Exit Connector / Cable, 100 mV/g.
-
Product
USB-4432, 102.4 kS/s, 100 dB, 0.8 Hz AC/DC Coupled, 5-Input Sound and Vibration Device
780421-01
Sound and Vibration
The USB-4432 is designed for sound and vibration measurements. Four of the input channels incorporate integrated electronic piezoelectric (IEPE) signal conditioning for accelerometers and microphones and built-in antialiasing filters that automatically adjust to your sampling rate. The fifth input channel does not include IEPE support.
