Phasor Measurement Units
synced remote wave monitors measuring ac current and voltage on a power grid. Also known as: PMU
See Also: PMU, Smart Grid
-
Product
2-18GHz Instantaneous Frequency Measurement Unit
DR058-F2
-
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
-
Product
Control Units
-
Astronics PGA offers two major architectures for Carat® Motion Systems: with or without integrated power supply. This allows you to choose the most optimized architecture for each of your different installations.
-
Product
Switching Unit
ZET 454
-
The ZET 454 switching unit is intended for serial switching of 72 circuits of ZET 452 control devices to one of the sixteen sockets. The ZET 452 electric circuits control device is connected to a socket on the ZET 454 switching unit front panel. On the front panel of ZET 454 there also are sockets for tested device circuits connection, which is performed using the adapter harnesses.
-
Product
Benchtop Units
-
Provide real-time or near-real-time data on chemical reactions and manufacturing processes.
-
Product
Electronic Units
-
Electronic units for field installation and mounting rack installation control the actuators. They are fed with 115 or 230 V AC. A local control panel allows for easy basic settings.
-
Product
Auxiliary Power Units
-
Honeywell Aerospace Technologies
Honeywell is the largest producer of gas turbine auxiliary power units (APUs) found on many leading aircraft. With more than 95,000 APUs produced and more than 36,000 in service today, Honeywell has a large APU installed base and is poised for further growth. We’re powering more than 150 regional, executive, commercial and military applications, including both fixed wing and rotary wing.
-
Product
Jandel Test Unit
HM21
-
The Jandel HM21 Test Unit has six constant current settings between 100nA and 10mA, and can be used to measure voltages from 0.01mV to 1250mV.
-
Product
Precision Source/Measure Unit, 1 Ch, 10 FA Resolution, 210 V, 1.5 A
B2910BL
-
The Keysight B2910BL Precision Source / Measure Unit (SMU) is a 1-channel, compact and cost-effective bench-top SMU with the capability to source and measure both voltage and current. It is versatile to perform I/V (current vs. voltage) measurement easily with high accuracy. Integration of 4 quadrant source and measurement capabilities enables I/V measurement simply and easily without configuring multiple instruments.
-
Product
Control Unit
Epec 5050
-
Epec 5050 Control Unit is ideal for applications that require plenty of I/O and enhanced algorithms. Epec 5050 control unit has also a large memory and its I/O is widely programmable. For example, PI pins’ threshold voltage can be selected and many inputs have pull-up/pull-down selection.
-
Product
Measurement
Torsiograph
-
Torsiograph is used for measuring the rotation non-uniformity in rotating parts of various mechanisms. Torsiograph generates virtual channels for displacement and displacement velocity. These channels are available for further analysis by ZETLAB programs, e.g. for displaying on the oscillograph.
-
Product
Portable Interface Unit
1553-USB-PIU
-
The 1553-USB-PIU is a Portable Interface Unit providing full MIL-STD-1553 test, simulation and bus analysis capability in a compact self-contained unit, to connect via a USB interface to suitable host systems. The unit provides support for all 1553A, 1553B, McAir and STANAG 3838 variants in a self contained battery operated unit, and is supplied with a matching power supply and battery charger unit for desk-top use. The 1553-USB-PIU supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The unit is supplied with "C" Driver library, together with a Windows GUI, providing a user friendly software tool for all 1553 set-ups, data management and storage.
-
Product
RFID Evaluation Units
-
- Wide range of interfaces for RFID evaluation units- Robust antennas and ID tags with long writing / reading distance
-
Product
Surface Display Unit
Multigauge 3100
-
Used with the Multigauge 3000 to provide displayed measurements on the surface. Two way communication to the Multigauge 3000. Ideal for class surveys or when visibility is poor.
-
Product
Intelligent Detection Units
-
Measurement of the ambient dose rate equivalent of continuous and average dose rate of pulsed X-ray and gamma radiation in an extremely wide range in harsh operating conditions.
-
Product
Safety Control Unit
Epec SC52
-
SC52 offers a flexible solution for software-based safety function implementation. Together with the SC52 controller, Epec offers a set of pre-certified PLCopen application libraries in order to reduce customer’s safety related software development effort.
-
Product
Data Broadcast Units
-
The DBU-TTL Data Broadcast Unit is designed for use in receive only data broadcast applications. The unit supports 8-Ports Data/Clock distribution of TTL signals on BNC connectors. 1U rack mount chassis.
-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
-
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
-
Product
Activity Detection Unit
DG009-M1
-
Many advanced EW receivers, particularly those associated with ECM jamming systems, do not require the high resolution frequency information associated with a DFD or IFM based receiver. This is typically the case where a single pulse present within a broad frequency band is required to be detected and instantaneously down-converted to an IF band.TDS manufactures a range of Frequency Activity Detectors (FADs) also known as Activity Detection Units (ADU) which perform frequency measurement of an RF pulse and output data in as little as 15ns. The basis of these products is TDS’s ability to produce high performance broadband channelisers and integrated detectors. These devices are ideal for receivers which must operate in very high pulse density environments.
-
Product
PXIe Source/Measure Unit, 15 MSa/s, 1 PA, 60 V, 3.5 A DC/10.5 A Pulse
M9602A
-
The Keysight M9602A is a PXIe SMU featuring best-in-their-class narrow pulse width as narrow as 10 μs. It enables dynamic/pulsed measurements with up to 15 MSa/s for broad emerging applications such as VCSEL optical devices.
-
Product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
-
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
Battery Extra Load Units
-
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
Product
Instrument Test Unit
-
Instrument Test Unit For Advanced Inertial Sensors (INTU) is used for testing and evaluation of Ring Laser Gyro (used in GSLV/PSLV launch vehicles), that detects the angular displacement during rotation. The INTU receives displacement signals from the sensor (RLG) to evaluate the sensor characteristics and also generates signals required towards initiating the action of the sensor.
-
Product
Source / Measure Unit (SMU) Modules, N6700 Power System
-
The Keysight N6780 family of source/measure units (SMUs) provide advanced features and precise control and measurements of voltage and current down to the microampere and nanoampere regions. They provide stable, glitch-free output voltage and current during high-speed load changes, fast output modulation, and high-speed measurements of both voltage and current simultaneous.
-
Product
Extension Unit
ZET 452 MP
-
The ZET 452 MP extension unit improves the capabilities of electric circuit parameter control devices:*increases the number of measuring circuits;*makes it possible to build distributed systems for cable networks checking.
-
Product
Test And Measurement
-
Test and Measurement supplies test, measurement, and analysis equipment and software for product design optimisation, manufacturing control, and environmental monitoring systems. Markets are principally the aerospace, automotive, consumer electronics and oil and gas industries. For customers in the automotive and aerospace industries, our products and applications help them to design and test new products whilst reducing time to market. In consumer electronics, our equipment and software enable customers to refine the performance and accuracy of their products and to test them in the production process. In the environmental monitoring market, the desire for higher standards of community comfort is creating additional demand. In the oil and gas industries, our products and solutions optimise the recovery rates of oil and gas reservoirs and support the development of cost-efficient extraction processes in a safe manner that minimises the impact on the local environment. The operating companies in this segment are Brüel & Kjær Sound & Vibration, ESG Solutions, HBM and Millbrook.
-
Product
Portable PD Acquisition Unit
AQUILA
-
Techimp AQUILA has been expressly designed to respond to all these needs being a robust and compact portable all-in-one PD detection station providing a full range of options ideal for on field applications. It can cope with the toughest outdoor conditions while taking measurements on any electrical asset. 15 years of service experience has been condensed in this unit integrating TECHIMP innovative PD detection technology with multiple connectivity (Wi-Fi, Fiber Optics, USB, Bluetooth) and power supply.
-
Product
Nano Interface Unit
NIU1A
-
NAI's NIU1A is a nano unit with an integrated power supply, one function module slot, and an optional ARM Cortex-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications, and delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in less time, with NO NRE.
-
Product
Removable Storage Unit
PXI-DM-U.2
-
The PXI-DM-U.2 PXI Express Storage Unit provides up to 15.36 TB of removable NVME solid state storage (SSD) in a single PXI Express slot. The storage module addresses the requirements of users who need to remove and replace PXI Express storage for security, archival or other reasons.
-
Product
0.5-2.4GHz Instantaneous Frequency Measurement Unit
DR063-M2
-
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
