-
Product
622 HP Eddy Current Chassis Dynamometer
CM-51-EC
-
Weight Capacity: 25,000 lb (11,340 kg) per axleRoll Brakes: pneumatically-actuated discShipping Weight: 8,340 lb (3,783 kg)Capacity: 622 hp at 45 mph (464 kW at 72 kph)Rolls: 20 by 36 in. (508 by 915 mm) long4 front fixed rolls, 2 rear rolls fixed toaccommodate axle spreads from48 to 60 in. (1,219 to 1,524 mm)tandem centersPit Required Depth: 25 in. (635 mm)
-
Product
Eddy Current Dynamometer
EC Series
-
Specifically designed for small displacement diesel engines, the Eddy Current (EC-Series) engine dynamometer features in-line eddy current absorption units in a robust, compact frame. The air-cooled eddy current absorbers eliminate the need for an expensive water recirculation system and most engines being tested can be cooled with a standard closed-circuit radiator system. This compact air-cooled design results in a minimal environmental impact and the ability to be easily relocated with no need for a permanent installation. When combined with PowerNet LT, our fully automated dynamometer control system, all of your testing needs can be performed at the touch of a button.
-
Product
2WD Dynamometers
MD-250 Series
-
The MD-250 uses its powerful eddy current power absorber, a frictionless, air-cooled braking device, to enable it to apply variable and steady state loading. A complete control and data acquisition system lets you design a wide range of tests or select from a host of pre-configured tests included with the standard system.
-
Product
Load Banks
-
Power Test Dynamometer offers a complete high capacity load testing solution with our load bank and gen set testing systems. Capable of testing generators and AC/DC power sources, our load bank systems safely apply electrical loads across the entire spectrum of operation. By offering a one-stop-shop for your Load Bank and it's accompanying data acquisition software, Power Test is committed to Making Your Testing Easy.
-
Product
550 HP Water Brake Chassis Dynamometer
TD-24S
-
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 8,700 lb (3,946 kg)Capacity: 550 hp at 35 mph (410 kW at 56 kph)Rolls: 24 by 34 in. (610 by 864 mm) 4 front fixed rollsPit Required Depth: 27 in. (686 mm)
-
Product
1100 HP Water Brake Chassis Dynamometer
TD-36
-
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 13,200 lb (5,987 kg)Capacity: 1,100 hp at 45 mph (820 kW at 72 kph)Rolls: 36 by 31 in. (915 by 787 mm) 4 fixed rolls to accommodate axle spreads from 48 to 74 in. (1219 to 1880 mm) tandem centersPit Required Depth: 35 in. (889 mm)
-
Product
AWD Dynamometer
MD-AWD-150 Series
-
Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle.
-
Product
Engine Dynamometer
DX31-HS
-
Power: 250 hp (186 kW)Torque: 804 lb-ft (1,091 Nm)Speed: 6,000 rpmWater Use*: 19 gpm (72 lpm)Inertia Value**: 23.3 lb·ft2 (0.98 kg·m2)Shipping Weight: 1,254 lb (569 kg)Rotation: bi-directional
-
Product
Mechanically linked AWD Performance Dyno
-
Mustang''s AWD-500 can be operated in AWD Mode while testing two-wheel drive vehicles. This process allows the non-driven axle to be spun by the dynamometer rollers at the same speed as the driven axle, eliminating the speed differential that occurs on two-wheel drive dynamometers problem solved.
-
Product
Eddy-Current Dynamometers
WB Series
-
Eddy-Current Brake Dynamometers (WB Series) are ideal for applications requiring high speeds and also when operating in the middle to high power range. Eddy-Current Brakes provide increasing torque as the speed increases, reaching peak torque at rated speed. The dynamometers have low inertia as a result of small rotor diameter. Brake cooling is provided by a water circulation system, which passes inside the stator to dissipate heat generated by the braking power. The water cooling in the WB provides high continuous power ratings (max. 140 kW). The WB dynamometers have accuracy ratings of 0.3% to 0.5% full scale ( 2% for WB 2.7), depending on size and system configuration. Additional options include: high-speed version, speed pickup, mechanical rotor blocking device, OEM version IS and vertical mounting.
-
Product
Engine Dynamometer
DX36
-
Power: 1,500 hp (1,119 kW)Torque: 4,825 lb-ft (6,542 Nm)Speed: 4,000 rpmWater Use*: 109 gpm (412.6 lpm)Inertia Value**: 121.6 lb·ft2 (5.1 kg·m2)Shipping Weight: 2,240 lb (1,016 kg)Rotation: bi-directional
-
Product
Cycle-ATV Dynamometers
EC997
-
The EC997 Series, our standard eddy current motorcycle chassis dynamometer, takes motorcycle performance tuning to the next level. The EC997 Series uses the industry’s most advanced electronics and Dynamic Load Control technology, featuring precision closed-loop torque feedback – a standard feature with every EC997 dyno. Competitor’s dynos on the market allow you to apply “percent % load” but Mustang has perfected the art and science of Dynamic Load Control and proudly offer the most sophisticated Dynamic Load Control dynamometer available at any price. Our superior control technology combined with our ultra-low inertia design allows you to precisely control loading to hold the engine at each RPM. Try doing that with a heavy drive roller and insufficient control technology – you simply cannot! Mustang has delivered thousands of performance dynamometer systems over the past 35 years and has perfected the art and science of dynamic vehicle loading and dynamometer control. We include each motorcycle make and model in our database including weight and drag coefficients so you can simulate the track right on the dyno! While other dyno manufactures are still trying to catch up with our technology, Mustang continues to lead the industry and is recognized around the world as the industry’s best with regards to dynamic dynamometer controls. Mustang has built racing dynos for Harley-Davidson as well as several end of production line testing cells for Harley-Davidson, Honda, and Polaris.
-
Product
Running Line Tensiometer
TIMH
-
The TIMH - running line tension meter range are built with dockside, marine, offshore, towage and salvage applications in mind. It is particularly useful where there is no anchor or dead end on the line to rig a Straightpoint Radiolink or Loadlink digital dynamometer to measure tension force.
-
Product
Dynamometer Controls, Data Acquisition Systems and Instrumentation
-
Whether you want a basic engine dynamometer configuration that provides torque, rpm and power or need an advanced, full-featured test and measurement software package, Taylor has a data acquisition system that will serve your unique application without breaking your budget. Contact Taylor to discuss which instrumentation system and related accessories are right for you, and turn your testing challenges into success.
-
Product
Engine Dynamometer
DE720
-
Power: 966 hp (720 kW)Torque: 3,320 lb-ft (4,500 Nm)Speed: 3,750 rpmWater Use*: 124 gpm (469.4 lpm)Inertia Value: 126 lb·ft2 (5.3 kg·m2)Shipping Weight: 9,259 lb (4,200 kg)Rotation: bi-directional*No Cooling System
-
Product
1100 HP Water Brake Chassis Dynamometer
TD-24
-
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred
-
Product
Test Cell Measurement
-
Accurate Technologies’ long history in powertrain development provided insight into the day-to-day issues that were occurring during engine testing at a time when electronic devices were being introduced to monitor performance instead of traditional mechanical means. Outside of the harsh physical environments, devices used in these applications need to perform difficult high-voltage signal conditioning and high-speed synchronous pulse processing. ATI developed unique products that satisfy specific test cell or dynamometer challenges. These highly accurate products measure engine timing (IGTM) or speed (SmartTach) in convenient ways to provide information that otherwise may not be available.
-
Product
Portable Electrical Measuring Instruments in ABS Body
-
Supreme Instrument Laboratories
General Specification for Portable Ammeters, Voltmeters, Milliammeters, millivoltmeters, Micro Ammeters, Single phase Wattmeters, power Factor Meters, Dynamometer type Voltmeters, Ammeters etc. Housed in superior grade of ABS body, unique design, very strong in construction, unbreakable and very high insulation.
-
Product
Towing Dynamometer
RSL-25K
-
RSL-25K Towing Dynamometer is designed for testing today’s full-sized cars, SUVs and light trucks. The RSL25K is built with a steel frame, sheet metal body and rides on an independent, coil spring suspension. The RSL-25K uses eddy current absorbers for power absorption. The power is provided by batteries and an alternator.
-
Product
AC Engine Dynamometer
DA16
-
Power: 16 hp (11.9 kW)Torque: 42 lb-ft (56.9 Nm)Maximum Speed: 6,400 rpmConstant Torque Range: 0 - 2,000 rpmConstant Power Range: 2,000 - 3,200 rpmDecreasing Power Range: 3,200 - 6,400 rpmRotation: bi-directional
-
Product
Dynamometer
ECB Series
-
ECB Series Electric Motor Dynamometers allow for ease of testing as they offer the advantage of dissipating heat via air-cooled fin technology.
-
Product
Testing Electric Pump Motors
-
This Custom Motor Test System is designed for the testing of 5 different sized electric motors used in various sump, utility, sewage, well, pool and pond pumps. All of the components mentioned above are mounted on a versatile table that can be easily reconfigured and retrofitted to any Magtrol dynamometer.
-
Product
Towing Dynamometer
RS-40K
-
RS-40K towing dynamometer is designed for testing today’s DOT Vehicles (Classes 5 and 6) which include trucks and buses. The RS-40K is built with a heavy-duty steel frame, industrial axle and rides on an air ride suspension. The RS-40K is designed to maintain 40,000 Newtons of constant drawbar force and the ability to simulate an uphill slope of 25%. The dyno uses eddy current absorbers with special high temperature coils. The power is provided by an industrial generator. Testing is unlimited at lowspeeds.
-
Product
Emissions Dynamometers
MD-ASM-150-AWD (4×4)
-
The MD-ASM-150-AWD (4×4) tests both axles of the test vehicle under the same imposed load; while at the same time providing for front-to-rear axle speed synchronization. Front-to-back roller speed synchronization protects AWD center differentials, provides for a means to safely test 2WD vehicles with traction control, and allows for testing to be performed under real-world load conditions. The MD-ASM-150-AWD (4×4) accommodates wheelbases from 86 to 128 inches (218 – 325 cm) without moving parts.
-
Product
Electric Motor Test Systems
-
Electric Motor Test Systems feature our highly successful water brake dynamometer which is used as an electric motor loading device.
-
Product
Software
Hole Shot
-
The modern world is changing faster than ever before and most companies and governments are migrating away from older Windows based networking technologies to web-based networks that are endlessly interconnected making information easier to share and easier to access from any device at any time. Mustang adopted web-based technology in 2016 when it embarked on a new project to advance dynamometer technology and simplify its offerings. Mustang’s goal was to increase commonality and provide customers with a more powerful and easier to manage controls package. Mustang already offered a full menu of testing capabilities, so we turned our attention to increasing access and decreasing clutter. By adopting web-based systems, Mustang can better service thousands of customers world-wide from one location and keep all of our customers on the most up to date system available. All enhancements can be pushed to all of our customers at the same time making sure all installations are up to date. Our latest controls package, Hole Shot™ Software is designed to keep our customers constantly ahead of the curve and ensure that their valuable data is secure and backed up to a secured cloud database.
-
Product
Water Brake Engine Dynamometers
DS Series
-
Similar in design to the DX Series, Taylor Dynamometer’s DS Series Water Brake Engine Dynos DS dynamometers bring you proven durability. In addition, this line provides increased power capacity – from 2,125 hp up to 4,250 hp (1,584 kW up to 3,169 kW) – thanks to larger diameter components.
-
Product
Portable Engine Dynamometers
-
Cost-effective Portable Engine Dynos from Taylor Dynamometer are water brake style systems for diesel applications up to 1,250 hp (932 kW) and 3,000 ft-lb (4,068 N) of torque. Mount yours right on the engine in minutes for fast, convenient and reliable testing.
-
Product
1650 HP Water Brake Chassis Dynamometer
TD-24X3
-
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 22,000 lb (9,979 kg)Capacity: 1,650 hp at 35 mph (1,230 kW at 56 kph)Rolls: 24 by 34 in. (610 by 864 mm) 4 front fixed rolls, 2 sets of 2 rear rolls to accommodate axle spreads from 48 to 66 in. (1,219 to 1,676 mm) tandem centers and 52 to 62 in. (1,321 to 1,575 mm) tridem centersPit Required Depth: 27 in. (686 mm)
-
Product
Real Car Transient Test System
RealCar Simulation Bench
-
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
