-
Product
AI Inference System
MIC-741-AT
-
AI Inference System Powered by NVIDIA® Jetson Thor™. Embedded with NVIDIA® Jetson T4000™ up to 1200 TFLOPS (FP4). Supports 1 x SFP28 (1 x 25GbE). Supports 2 x 1GbE, 2 x 10GbE4, 6 x USB 3.2 Gen 2, 2 x M.2 2280, 1 x M.2 Ekey (Support both WiFi AEKey), 1 x M.2 Bkey (LTE,5G).
-
Product
Infiniium MXR B-Series Oscilloscope: 2 GHz, 8 Channels
MXR208B
-
MXR208B Infiniium MXR B-Series, 2 GHz on all 8 channels, option to integrate 8 instruments in one, hardware accelerated plotting, and fully upgradeable , including up to 6 GHz.
-
Product
PXI-6236, 4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module
779622-01
-
4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6236 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6236 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6236 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
Product
Intel® Core™ I Automation Computer With 2 PCI(E) Expansion Slots
UNO-3283G
-
6th Generation IntelR Quad Core Processors with 8GB DDR4 Memory2 x GbE, 6 x USB 3.0, 2 x RS-232/422/485, 2 x RS-232 (pin header), 1 x DVI-I, 1 x HDMI1 x PCIex16, 1x PCI, 2 x mPCIe (2 x full), 1x CFast slot, 1 x mSATA slot (optional)Thumb screw for easy maintenanceHot-Swappable HDD/SSD support for RAID 0/1Easily exchangeable RTC batterySupports Fieldbus Protocol by iDoor TechnologyChassis Grounding ProtectionLAN Redundancy (Teaming)
-
Product
VECTOR-GUN HANDHELD DIRECTION FINDING ANTENNA SYSTEM
HFDF
-
National RF's Type HFDF active directional antenna system consists of a high gain RF amplifier coupled to a tunable Faraday shielded loop antenna. Several loop antenna assemblies are available to provide coverage of frequencies in the HF and low VHF spectrum. Due to the nature of a Faraday shielded loop, the antenna exhibits a sharp null through the diametric center of the loop. This null is used to determine the direction of incoming radio signals or to locate electrical noise being radiated from some source. The internal high gain amplifier is used to compensate for the inherent inefficiency of the actual loop at the operating frequency. Overall, the system dynamic response is about +6 dB as compared to the dynamic response of a dipole. To aid in the direction finding process on strong signals, an internal 30 DB attenuator is provided. As the loop antenna presents a bi-directional response, tri-angulation may be required to eliminate the ambiguous signal direction. The line of site of the incoming signal is determined by listening for a signal null on the receiver or by watching the receiver’s S-meter.
-
Product
Development Board
SOM-DB5830
-
Development Board for COM Express® R2.1/3.0/3.1 Type 6 / 10 Modules. Expansion: PCIe x16, PCIe x4, Display Type: VGA, LVDS / eDP, HDMI / DP. ATX form factor with both ATX & AT power support.
-
Product
Oscilloscope, 6 GHz, 80 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits
WaveMaster 8060HD
-
Oscilloscope, 6 GHz, 80 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits.
-
Product
SQUID Series Arrays
-
The SQUID series arrays are ideal for readout of TES sensors or as amplifier stage for discrete two-stage applications. Integrated bias resistors for TES or two-stage applications reduce wiring complexity. Various arrays with input inductances of 3 to 6 nH, input sensitivities of 17 to 23 µA/Phi0, and a current noise between 5 and 10 pA/sqrt(Hz) @ 4 K are available.
-
Product
Oscilloscope - 1-6 GHz, 4 Analog Channels
DSOX6004A
-
1 GHz - 6 GHz4 analog channels Easily view and isolate signals on the 12.1-in capacitive multi-touch screen with Zone triggering and 450,000 wfms/s update rate Make more precise measurements with 115 uVrms noise floor at 1 mV/div (1 GHz)Get performance measurements anywhere with the portable 6-in deep size Quickly see analysis details with standard histogram and color grade View signal integrity with jitter and eye diagram analysis options
-
Product
LGA 1700 Intel® 12th Gen. Core™ MicroATX Server Board with 4 x DDR5, 3 x PCIe (1 x Gen 5, 2 x Gen 4), 6 x USB 3.2, 5 x SATA3, Quad/Dual LANs, and IPMI
ASMB-588
-
- LGA 1700 Intel® 12th Gen. Core™ i9/i7/i5/i3 processors with W680 chipset- DDR5 ECC/Non-ECC 4400/4000/3600 MHz UDIMM up to 128 GB- One PCIe x16 (Gen 5) and two PCIe x4 (Gen 4) slots- Triple displays - DVI-D, VGA, and HDMI 2.0 ports- Five SATA 3 ports and six USB 3.2 ports- One M.2 2280 (PCIe x4)- Rackmount optimized placement with positive air flow design- 0 ~ 60 °C (32 ~ 140 °F) ambient operating temperature range
-
Product
ENA Vector Network Analyzer
E5063A
-
2-port, 50 ohm, S-parameter test set Select the VNA frequency option that best suits your test needs and budget, and upgrade options at any time Boost efficiency and productivity with the consistent measurement framework of the industry-standard vector network analyzer Enhance your PCB manufacturing test capability with Option 011Easier operation with support for 6 languages via softkey & the embedded help manual in English/Simplified Chinese Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Digital Circuit Breaker Analyzer
CT-8000 S3
-
The CT-8000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-8000 S3 is available with 3 (part number 9103-UC) or 6 contact timing channels (part number 9104-UC). The CT-8000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Also, an outstanding feature of the CT-8000 S3 is the ability to perform dynamic resistance tests on circuit breaker contacts.
-
Product
PXI 4-Slot BRIC Matrix, 30x32 1-Pole (6 Sub-cards)
40-562B-021-30X32
-
The 40-562B-021-30X32 is a high density BRIC4 matrix module with a size of 30x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
180V-260V AC Socket Tester With RCD Test (For UK)
1943
-
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 180~260VAC circuit.*LED indicators & Digital display.*30mA leakage current measurement.*RCD Test.I*t can perform self test after plug-in ( Voltage sould be above 180V ).*Detect faulty wiring status in 3 wire receptacle.*This socket tester will give LED indication as well if the main voltage is below 200V or above 260V.*Earth loop impedance test.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 11W*Frequency: 50Hz
-
Product
4G Router
BB-SR31000320
-
SmartFlex, Global, 2x Ethernet, 1x RS232, 1x RS485, Metal, Without Accessories. Global LTE Cat.4 high speed connectivity with 3G fallback, 2× SIM. LTE B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B38, B39, B40, B41. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
Cable Assembly, Receiver, Tripaddle, 36”, 6 9-PIN DSUB
540352010201
-
Cable Assembly, Receiver, Tripaddle, 36”, 6 9-PIN DSUB
-
Product
Dial Indicators
-
1. Always select the dial test indicator that best fits the application.2. Care should be taken while using a dial test indicator, try not to jolt the indicator, should you be unfortunate and drop a dial test indicator, get it re-calibrated/repaired before reusing it.3. Replace worn contact points only with those of a similar length from the centre of the ball stylus to the abutment shoulder.4. Always clean dial test indicators after use with a lint free paper or cloth and store the indicator in its box or in a dust free area.5. When using a dial test indicator, always position the dial test indicator in a horizontal plane to the surface media.6. Always use a rigid stand for mounting the dial test indicator.7. When measuring a rotating object, either between centres or in a vee block, ensure that the object is rotating in the correct direction. Never rotate the workpiece towards the contact point.8. When measuring a sliding object, only take readings when the object is moving directly towards the contact point, never away from the contact point or in a sideways manner.9. Avoid parallax errors by reading the dial directly from the front and square on to the dial.10. Never oil a dial test indicator as this attracts contamination, should the movement become erratic then the dial test indicator should be submitted to a reputable repair agent.11. Try not to expose dial test indicators to direct sunlight or in a high humidity environment.12. Never use a dial test indicator that has not been calibrated, if in doubt consult an appropriate authority.
-
Product
Noise Source
MNS-1
-
Matrix Test Equipment Incorporated
The MNS-1 is a shaped noise source that can be used toemulate 2 bands of digital carriers. While it does not havethe necessary attributes to generate a constellation, it doesmimic the loading of QAM carriers. The MNS-2 featuresremotely controllable 6 MHz wide notch filters to allowintroducing a QAM carrier capable of generating a constellationand enabling measurement of Modulation Error Ratio (MER) andBit Error Rate (BER).
-
Product
LXI Microwave Multiplexer, SP6T, 2-Bank, 50GHz, 50Ω, SMA-2.4
60-800-602
-
Our 60-800-602 is a 2 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
4G Router
BB-SR30900020-SWH
-
SmartFlex, Korea, 2x Ethernet, Metal, Without Accessories. LTE cat.4, 3G/HSPA+, GPRS/EDGE, Korea, 2x SIM - SKT carrier only (KT and LG U+ are not supported). LTE B1, B3, B5, B7, B8, B20, B38, B40, B41. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
4G Router
ICR-3241W-1ND
-
ICR-3200, NAM, FirstNet, 2× Ethernet, 1× RS232, 1× RS485, Wi-Fi, Metal, Without Accessories. 4G LTE Cat.4 VPN Gateway for Industrial IoT applications - FirstNet Certified. LTE B2, B4, B5, B12, B13, B14, B66, B71. Carriers support; Verizon, AT&T, T-Mobile, FirstNet (Public Safety).
-
Product
6 Slots Chassis
Monoblock AXIe-0
-
The monoblock is a device that ensures the functioning of various AXIe-0 instrument modules installed in it, under the control of an embedded personal computer.
-
Product
Multi-Channel Attenuation Control Unit (5-channels), DC to 6 GHz, 0 to 121 dB, 1 dB Step
J7205A
-
The J7205A is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to5 devices under test (DUT). Operating frequency from DC to 6 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205A reduces cost of ownership and provide the best measurement accuracy.
-
Product
4G Router
ICR-2734WA02
-
ICR-2700, EMEA, 2x Ethernet, USB, Wi-Fi, Metal, UK Accessories LTE Cat.4 with 3G/2G fallback. 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
UV Light Meter
Model 308T
-
Built for high intensity applications the NEW OAI Model 308T UV Light Meter is a dependable, direct-reading instrument designed for measuring UV light intensity for UV curing. The Model 308T features detachable probes for use in the UVA, UVB and UVC ranges, plus a high speed serial port. Accuracy of the meter is within ±3%and measurement repeatability is within ±3 LSB (least significant bit). Like all OAI precision instruments, the Model 308T provides NIST traceable measurements. This easy-to-use meter is auto-ranging from 0.1 to 1999.9 milliwatts/cm2 full scale when used with the 2000 milliwatts/ cm2 probe. The linearity of the meter in this range is at least ±(.002% + 6 LSB).
-
Product
Bench Power Supply, Adjustable, 2 Output, 0 V, 32 V, 0 A, 3 A
72-8690A
-
The 72-8690A from Tenma is a dual channel general DC power supply suitable for laboratory use. The dual channel (CH1 and CH2) can work in CV or CC mode and these two modes convert automatically according to the load. The CH1 and CH2 have auto tracking function. In this condition, the output of CH2 tracks the output of CH1. This function is usually used when adjustable symmetrical and double polarity power is required. Both CH1 and CH2 display the output voltage or current with a 6 digit LED meter. The main outputs can be connected in parallel or in series. This product comes with 2 years warranty.
-
Product
PXI Digital Pattern Instrument
-
The PXI Digital Pattern Instrument is designed for semiconductor characterization and production test. It provides 32 channels, a voltage range of -2 V to 6 V, a PPMU force voltage range of -2 V to 7 V, up to a 200 Mb/s data rate, and a clock generation rate up to 160 MHz. The module includes Digital Pattern Editor software as well as debugging tools like shmoo, digital scope, viewers for history RAM, pin states, and system status.
-
Product
Time Domain Reflectometer
TDR 500
-
Handheld Time Domain Reflectometer. The handheld time domain reflectometer TDR 500 and TDR 510 are used for fault location in all metal cables such as power cables, coaxial cables, data cables and communication cables.* Configurable for various measurement ranges and cable types* Standard-compliant, safe measurements on life cables through the measurement category CAT IV / 600 V (with separation filter)* Ideal for fault location in the area of telecommunication, video technology, data and security technology
-
Product
6-12V Heavy Duty Circuit Tester With Long Probe
1668A
-
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems. To indicate whether there is an electrical potential at any low voltage point in the system. By using the pointed contact tip to pierce insulation on cables, it will also indicate if current is present. This can be helpful when tracing faults or add cable to a circuit.
-
Product
PXI RTD Simulator Module 18-Channel PT1000
40-262-002
-
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
