-
Product
Graphite Rod & Plate Electrodes
GE1
-
High-purity graphite rod and disc electrodes for electrochemical applications. PTFE-insulated construction with multiple standard sizes available. Commonly used in electrochemical research, corrosion studies, electrocatalysis, sensors, and laboratory testing. Custom sizes and configurations are available upon request.
-
Product
Electrochemical Detector
800D
-
The Model 800C series is designed for electrochemical detection. This instrument can be used for monitoring the current passing through a flow cell in liquid chromatography/electrochemistry and in-flow injection analysis, as well as other electroanalytical applications.
-
Product
U-Type Glassy Carbon Electrode | 3mm
CS1-1
-
U-Type Glassy Carbon Electrode with PTFE insulation for electrochemical applications. Suitable for CV, EIS, electrocatalysis, corrosion testing, and electrochemical sensor research. Available in standard and custom configurations.
-
Product
Time-Resolved Electrochemical Quartz Crystal Microbalance
400C Series
-
The quartz crystal microbalance (QCM) is a variant of acoustic wave microsensors that are capable of ultrasensitive mass measurements. Under favorable conditions, a typical QCM can measure a mass change of 0.1-1 ng/cm2. QCM oscillates in a mechanically resonant shear mode under the influence of a high frequency AC electric field which is applied across the thickness of the crystal. Figure 1b below shows an edge view of a QCM crystal undergoing oscillatory shear distortion. The central portions of the top and bottom of the crystal are coated with a typically disk-shaped thin metal film (e.g., gold).
-
Product
Ruthenium Iridium / Iridium Tantalum / Platinum Titanium Electrode
RRC-1
-
Ruthenium/iridium-based titanium anodes with high corrosion resistance and stable electrochemical performance. Suitable for electrolysis, electroplating, wastewater treatment, and research applications. Custom coatings, geometries, and Ti plate/mesh formats are available.
-
Product
PowerNet Tester
-
The PowerNet Tester (BNT) is designed to test batteries, ultracaps and all other types of electrochemical power sources for 14 V and 42 V power net systems. Designed to test vehicle system batteries for 14V and 42V power net systems. But they may also be used for testing all other types of electrochemical power sources just by setting the required current and voltage values.
-
Product
10μm Transparent Quartz IDE Chip
TID1
-
The TID1 10um Transparent Quartz IDE Chip is an interdigitated electrode chip designed for gas sensing, humidity sensing, biosensing, impedance measurement, and MEMS-related electrochemical or electrical detection research. The 10 um transparent electrode geometry provides a defined interdigitated pattern for surface-functionalized sensing experiments. The quartz glass substrate supports optical access, transparent sensing, and photoelectric detection, while the IDE layout helps improve interaction between the electrode fingers and the target film, electrolyte, vapor, or biological interface.
-
Product
Carbon Steel & Stainless Steel Electrodes
CTE-1
-
CTE-1 Carbon Steel & Stainless Steel Electrodes is a research-grade electrochemical electrode or conductive component for use as a working electrode, counter electrode or custom laboratory assembly depending on the experiment. It is suitable for voltammetry, electrocatalysis, corrosion testing, sensor research and electrochemical cell development.
-
Product
Transmitter Monitors Carbon Monoxide
CO-R
-
The CO transmitter monitors carbon monoxide (CO) levels and is designed for the continuous monitoring of vehicle exhaust in non-hazardous areas. The CO uses a wide spectrum, long life electrochemical sensor to measure the amount of carbon monoxide in the environment. It is offered with an operating range of 0 to 125 ppm. Both the Room and Duct CO transmitters are offered in a standard NEMA 1 rated ABS Polycarbonate plastic enclosure. An optional NEMA 4X watertight and dust proof enclosure is only available with the CO room transmitter.
-
Product
Scanning Probe Workstations
-
BioLogic has over 25 years of experience producing scanning probe electrochemistry instruments. Initially this included a number of single technique instruments, with the first modular scanning electrochemical workstation, the M370, introduced in 2006, under the Uniscan name.Scanning probe electrochemistry has found use in academic and commercial research settings. It is applicable in any field in which bulk electrochemical measurements have been used. Scanning probe electrochemistry has found widespread use in: Corrosion and coatings, Biology, including biosensors and biotechnology, Batteries, fuel cells and photovoltaics, Materials, Catalysis
-
Product
Addon Cards
-
Fit the IM6/Zennium electrochemical workstation to your application. Control external potentiostats, capture additional physical properties or enhance your system to a true parallel impedance analyzer.
-
Product
Multi-Functional Electrochemical Cell (Double)
MCE-1-1
-
The MCE-1 Multi-Functional Electrochemical Cell (Double) is designed for laboratory electrochemistry, corrosion research, electrocatalysis, and multi-electrode experiments that require a configurable cell body. The double-cell structure supports comparative tests, separated compartments, or customized electrolyte arrangements. This cell is suitable for university laboratories, electrochemical materials research, and custom test platforms where electrode position, sealing, and modular accessories matter.
-
Product
Electrochemical Sensors
-
Electrochemical sensors are devices that provide real-time information about the composition of a system by connecting a chemically selective layer (recognition element) to an electrochemical transducer
-
Product
CellTest Multichannel Potentiostat
-
Simultaneous Electrochemical Impedance Spectroscopy (EIS) tests can be run on multiple cells by connecting Solartron 1455A/1451A series frequency response analyzer (FRA) modules to the 1470E. These FRAs can operate in single sine correlation or multi-sine / Fast Fourier Transform (FFT) analysis mode, providing the ultimate in speed, precision and accuracy. The 1455A FRA provides high performance impedance measurements over the frequency range 10 μHz to 1 MHz, while the 1451A FRA operates from 10 μHz to 100 kHz.
-
Product
Oxygen Sensors for Medical Products
-
USA manufactured electrochemical galvanic oxygen sensors (O2 sensors) for use in ventilators, anaesthesia machines, incubators, oxygen monitors and breathing gas mixes.Approved FDA, MDSAP, ISO13485, ISO9001 replacement oxygen sensors for respiratory medical devices with lifetimes up to 60 months. .
-
Product
5μm Silicon Gold Interdigitated Electrode (IDE)
SIG1
-
Silicon gold IDE chip with a 5μm gap for MEMS, photoelectric sensing, and high-precision electrochemical applications.
-
Product
Accessories
-
Electrochemical Accessories for Precision Testing – Cables, Clips, Cells & Lab Components
-
Product
H-Type Electrochemical Cell
SH-1
-
Sealed H-type electrochemical cell with circulation port, glass frit separator, 50–250ml volume, supports rubber or PTFE cap.
-
Product
L-Type Platinum Mesh Electrode
HPL-1
-
High-purity platinum mesh and sheet electrodes for electrochemical research, electrolysis, electrocatalysis, and laboratory applications. Available in L-type and clip-style designs with excellent corrosion resistance, high conductivity, and customizable dimensions to suit a wide range of experimental setups.
-
Product
Single Carbon Screen-Printed Electrode (SPE)
-
A single carbon screen-printed electrode (SPE) designed for electrochemical sensing, biosensor development, environmental monitoring, and laboratory research with excellent reproducibility and customizable electrode configurations.
-
Product
Percent Oxygen Sensors
-
At Process Sensing Technologies (PST), we offer replacement electrochemical oxygen sensors compatible with major fixed and portable oxygen analyzers in challenging industrial environments. Tailor your solution with our versatile housing options, allowing you to specify either a 2-ring or connector design.
-
Product
Custom Quartz Photocatalytic Sealed Electrochemical Cell
CQP-2
-
CQP-2 Custom Quartz Photocatalytic Sealed Electrochemical Cell is an electrochemical cell for laboratory research, designed for three-electrode testing, sealed or unsealed experiments, photocatalysis, corrosion studies, optical observation, or customized electrochemical workflows depending on the selected model.
-
Product
Combo Gas Monitor
Z-Gard Combo Gas Monitor
-
A cost-efficient monitor for underground garages and ventilation control, the Z-Gard Combo Gas Monitor uses an electrochemical sensor to detect carbon monoxide. The unit features local audio/visual alarm status indicators and it can be configured to interface with air-handling equipment to control air quality within a building.
-
Product
IDA Electrodes
-
Interdigitated Array (IDA) electrode is an electrode developed for electrochemical measurements to be performed in a very small quantity of the sample. IDA electrode could be applied for the detection and reaction analysis of the compounds in a small quantity of the sample. IDA electrode is a microelectrode pattern fabricated by using the lithography technology. The Electrodes are composed of 65 pairs. In each one of the pair has a function of the oxidation and reduction electrodes.
-
Product
The Golden STM
-
*Golden (chemically resistive) vibration isolated STM body with implemented preamplifier*Computer with PCI board based SPM controller *Anfatec Scan & Anfatec Present*19“ STM controller (extra low noise 24 bit converters)*HV display for z-direction*High voltage amplifiers for the x-y-tube scanning*Optional: PC controlled bi-potentiostat and electrochemical cell
-
Product
5μm Transparent Quartz Interdigitated Electrode Chip
TIF1
-
5μm transparent quartz IDE chip designed for MEMS, biosensing, gas sensing, electrochemical, and photoelectric applications.
-
-
Product
Electrochemical Impedance Spectroscopy (EIS)
-
Electrochemical impedance spectroscopy (EIS) is a method for the non-destructive characterisiation of thin layers, membranes, surfaces and films. Typically a small amplitude AC voltage (or current) signal is applied to a sample while the amplitude and phase relationship of the corresponding current (or voltage) signal is monitored.
-
Product
Micro Single-Channel Interdigitated Electrode Chip
MSI1
-
Single-channel IDE chip for MEMS, optical sensing, gas sensing, biosensing, and electrochemical research. Designed for reproducible electrochemical measurements with customizable electrode gaps and layouts.
-
Product
Screen-Printed Electrodes
-
Screen-printed electrodes (SPEs) for electrochemical sensing, biosensor development and routine analytical testing. PotentioLab supplies disposable carbon, gold, platinum and modified SPE formats for laboratory research, portable electrochemical systems and method development.
