Inspection
check and evaluate to a quality control value.
See Also: Inspection Systems, Inspection Services
-
Product
PWB Interconnect Stress Test
-
PWB Interconnect Solutions Inc.
Services to test the reliability of Printed Circuit Boards. PCBs).Coupon Inspection and Electrical Prescreen. Coupon Testing. Failure Location via I/R Photo Imagery. Failure Analysis.
-
Product
Non Destructive Testing (NDT)
-
NDT covers a wide group of testing techniques used to evaluate the properties of a material, part, product, weld or system without causing damage. NDT carried out at KLL includes:Liquid Penetrant Testing (LPT) is used for the detection of surface breaking discontinuities on magnetic and non-magnetic metallic materials.Fluorescent and colour contrast penetrants are available to be used in the following methods:-Water washableSolvent removablePost emulsifiableMagnetic Particle Inspection (MT/MPI) is used for the detection of surface breaking and slightly sub-surface (up to 2mm) discontinuities.Bench type crack detectors and portable units are employed producing various waveforms (i.e. A.C, HWDC and induced magnetic flow) to give both circular and longitudinal magnetism.On-site testing is carried out using electro magnetic yokes and permanent magnets producing induced magnetic flow.Ultrasonic Flaw Detection (UT), also known as Ultrasonic Inspection, is used for the detection of volumetric discontinuities in ferrous and non-ferrous products (forgings and castings etc.), and welds in magnetic and non-magnetic materials.UT is capable of penetrating metals, dependent on the material characteristics, up to 10m in length.Some thickness and depth checks can also be carried out using ultrasound.Radiography services are available through sub-contract booked in advance. Notice is required for on-site work.Personnel are available at short notice for in-house or on-site work in the UK and overseas.All inspectors undertaking non destructive testing (LPT, MT/MPI and UT) are qualified to, and meet a minimum of, PCN Level 2.PCN Level 3 supervision is available in-house for LPT, MT/MPI, UT offering consultancy services including procedure writing and commentary, auditing of techniques and Level 3 Supervisor cover.We can assist clients in product qualification, material testing, quality assurance and audit programmes.
-
Product
Standard & Top Paint Inspection Gauges
121/4
-
is a hand-held paint gauge that offers a quick, versatile method of coating examination and measurement in a portable, easy-to-use format.
-
Product
Protective Coating Inspection Kit 3
-
Measurement parameters include:Surface profileSurface temperatureClimatic conditionsCoating thicknessAdhesion
-
Product
Inspection Assist Software
-
RVI software is a must for streamlining your inspection processes and improving overall efficiency. Olympus inspection assist software provides support throughout the entire process, whether streamlining on-site inspections or assisting with remote report generation.
-
Product
Fiber Optic Inspection & Cleaning
-
One of the most basic and important procedures for the maintenance of fiber optic systems is to clean the fiber optic equipment.
-
Product
Wafer Internal Inspection System
INSPECTRA® IR Series
-
An infrared internal defect inspection system has been added to the INSPECTRA® series.It is now possible to inspection with both infrared and visual light in one system.
-
Product
Chip Inspection System
GEN3000T
-
GEN3000T is an inspection system that performs automatic inspection of individual semiconductor chips.This revolutionary chip surface inspection system was achieved by combining the chip handling technology cultivated by Toray with the inspection algorithm used in the "INSPECTRA®" wafer defect inspection system.
-
Product
Emissions Dynamometers
MD-ASM-100
-
High throughput demands of Centralized Emission Inspection require the use of rugged and durable emission inspection equipment. Designed from inception to withstand punishing use and misuse, Mustang Dynamometer has set the performance standards of equipment manufactured and used worldwide for centralized emissions testing. Our pioneering experience has led us to be the world leader in the design and manufacturing of rugged inspection and maintenance hardware and software for the I/M industry. We have centralized testing lanes installed all over the world in climates from cold to hot and from wet to dry. By the end of 2016 we estimate that our equipment has tested nearly 850 million vehicles. Continuous improvement leads us to innovative solutions based on our knowledge of design, service, maintenance, ergonomics and overall functional capabilities. Mustang I/M Centralized Emission Inspection equipment is designed for our customer’s demands. Compliant with EPA, BAR, and CENAM ASM specifications.
-
Product
Automated LED Inspection and Testing
-
Landrex Technologies Co., Ltd.
Automated LED Inspection and Testing
-
Product
Visual Inspection Software
AdVISE
-
R&S®AdVISE visual inspection software automates the process of visually monitoring an equipment under test (EUT) during a test sequence. This eliminates human inattention, ensures reproducible results and simplifies the test documentation. A typical application is EMS testing with R&S®EMC32 and R&S®ELEKTRA test software.
-
Product
Digital Inspection Kits
-
Ideal for ‘paperless’ quality assurance systems the kits come complete with ElcoMaster® Data Management Software for professional reporting and analysis.
-
Product
Concrete Inspection
-
Concrete structures are normally constructed using steel reinforcement and Elcometer offers Concrete Covermeters and Rebar Locators to either measure the depth of concrete over the rebar or simply to detect the rebar under the surface. Half-cell versions of the Covermeter can be used to assess the probability that corrosion is taking place on the rebar. Test Hammers are used to assess the surface hardness of cured concrete and Elcometer offers several moisture meters that can be used to determine if the structure is sufficiently dry for coating.
-
Product
Jerking Tester
JLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard:JB/T4279.5-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.000mm and below;Built-in small ultra-quiet air compressor would provide power supply and automatic constant pressure;Samples, while being jerked, would not move and slip out;
-
Product
Thickness and Flaw Inspection
OmniScan SX
-
Olympus is proud to introduce the OmniScan® SX, a flaw detector that benefits from more than 20 years of phased array experience and shares the OmniScan DNA. For improved ease of use, the OmniScan SX features a new streamlined software interface displayed on an 8.4 in. (21.3 cm) touch screen. A single-group and non-modular instrument, the OmniScan SX is easy to operate and cost-effective for less demanding applications.
-
Product
Test Solutions Services
-
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
Product
Process Control, Measurement and Inspection Workstation
ScanINSPECT VPI
-
ScanINSPECT VPI is a fully integrated, stand-alone process control, measurement and inspection and programming workstation for use in setting up processes before the production floor in the PCB or Hybrid Microcircuit assembly industries.
-
Product
Conformal Coating Inspection (CI AOI)
-
They cover the components, the area around the components and identify most coating issues including cracks, bubbles, insufficient / excess coating, loss of adhesion and other common contaminations. Full coverage inspection for conformal coating.
-
Product
Post Wire and Die Bond Inspection Machine
IV-T3300
-
IV-T3300 is a post wire and die bond inspection machine with Dual JEDEC Tray Feeder System. It features a large inspection area of 600x500mm and a quick trays change of 5-7 seconds.
-
Product
3D Solder Paste Inspection
aSPIre 3
-
Industry-leading measurement accuracy and inspection reliability- Perfect solution to eliminate shadow problems, base plane settings, and problems with projection direction- Full 3D foreign material inspection solution for the entire PCB- High productivity through the highest accuracy
-
Product
Appearance Inspection
-
We perform quality assurance agency of customers' important products through inspection.
-
Product
Terahertz Imager for Material Inspection
T-SENSE FMI
-
This highly efficient technology is based on the most recent research results. Production can be monitored and controlled at various levels. T-SENSE FMI uses millimeter waves in the lower terahertz range with no health risks involved. This means that the equipment can be used anywhere and for several purposes without the need for radiation protection.
-
Product
Measuring And Inspection Systems For Rubber And Tires
-
The rubber processing industry, as well as the tire production process is supported by Micro-Epsilon with a range of systems for inspection, monitoring and control of miscellaneous processes.
-
Product
Pulsed DC Holiday Detector Inspection Kit
280
-
The Elcometer 280 Pulsed DC Holiday Detector is a ‘stick type’ holiday detector that has been designed to make pulsed DC high voltage holiday detection safer, easier and more reliable than ever before.
-
Product
PosiTector Inspection Kits
-
PosiTector Inspection Kits contain a PosiTector gage body (Standard or Advanced) and 3 probes – coating thickness, environmental and surface profile, as well as, accessories in a convenient hard shell carrying case.
-
Product
Gun Barrel Care Solutions
AGICAM 2
-
Aeronautical & General Instruments Ltd.
AGI’s Visual Inspection Camera System has been designed to compliment and be used with the Gun Barrel Bore Gauge. One single instrument that will provide accurate repeatable measurements, whilst also being able to view and record the condition of the barrel.
-
-
Product
X5 Spacesaver X-Ray Inspection
-
Designed to be integrated into line with optional free standing reject, Available in 300mm and 500mm belt width models, the X5 SpaceSaver is perfect for packed products with a width of up to 250mm.
-
Product
Ultrasonic Inspection System
PULD 40
-
The PULD-40 is a versatile and highly accurate ultrasonic inspection system designed to meet the needs of our customers.
-
Product
Solder Paste Inspection System
LaserVision SP3D Mini
-
The LaserVision SP3D Mini offers the same level of overall measurement capabilities as the VisionPro SP3D. Utilizing a lower cost microscope platform and the ability for customers to supply their own PC if needed, the SP3D Mini sets the "affordable" boundary on reliable, low cost SPI solutions.
