POST Cards
read BIOS error codes during a Power On Self Test for computers unable to boot-up.
See Also: Cards, Extender Cards, Probe Cards, Test Cards, PCI Diagnostic Cards, Post Codes
-
product
PCI High Density Pecision Resistor Card
50-298-031
The 50-298-031 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 13.6kΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PCI Mezzanine Card
PNIC1G
Each Ethernet interface supports 10, 100 and 1000 Mbits transmission rates with auto-negotiation for full duplex operation; 10 and 100 Mbit/s transmissions for half duplex operation, and is equipped with a 32 Kbit Serial EEPROM.
-
product
Analog-to-Digital Converter (A/D) and Counter-Timer Card
AD8-16 (ADA-8)
Model AD8-16 (alternate part number ADA-8) is an economical, multiplexed, eight-bit Analog-to-Digital Converter (A/D) and Counter-Timer card for ISA-bus computers. It accepts up to eight differential or 16 single-ended analog inputs (jumper configured). AD8-16 requires a full-size expansion slot. All connections are made through a standard 50-pin connector. Base I/O address selection is via dip switch.Analog inputs are multiplexed, amplified, held by a sample and hold amplifier, and then digitized by an eight-bit A/D converter. Amplifier gain is selected by software and can differ from channel to channel.
-
product
Signal, Contact, Receiver, TriPaddle, 5 Amp, .025" Round Post
610110179
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAAVG Mating Force(lbs) 0.41Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 Cycles
-
product
PCI Card
EXC-1394PCI
The EXC-1394PCI card for the PCI bus is an intelligent test and simulation card for interfacing to an IEEE-1394 data bus. It implements a 1394b PHY layer, operating at 100, 200, or 400 Mbps.
-
product
ARINC825 Cards
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
product
Multi-Function I/O FPGA PXI Card
GX3722
The GX3722 is a user configurable, FPGA-based, 3U PXI card which employs a multi-function, analog / digital, I/O daughter board. The module offers multiple analog and digital source / measure capability. The daughter board interfaces to the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA.
-
product
Time Synchronization Card
PMC/XMC
IXI Technology’s highly-accurate card provides time down to 62.5ns resolution in UNIX format. Its time-sourced, disciplined, voltage-controlled crystal oscillator (VCXO) or optional CSAC not only allows it to provide sub-second resolution, but also to “flywheel” during the absence or loss of carrier. The module has a status LED that indicates when the internal time is synchronized with the input time code. The card provides a programmable offset on its internal time from the input time source. The generated IRIG-B or 1588 output can be configured to be synchronous to the chosen input time source or configured to use the best available time source.
-
product
PCI Switch Cards
Pickering's range of PCI instrumentation grade switch cards can be cascaded to form larger switching networks.
-
product
6U Compact PCI Gigabit Ian Card
CP69601
LinkedHope Intelligent Technologies Co.,Ltd.
CP69601 is designed as 6U Compact PCI Gigabit lan Card. It supply two redundancy Gigabit lan ports on front panel. The controller ic is intel 82546GB. It support 32/64 bit, 33/66MHz CPCI bus.
-
product
XMC Display Control Card
XM61000
LinkedHope Intelligent Technologies Co.,Ltd.
XM61000 is an XMC display control card independently developed by Linghao Intelligence®. It is mainly targeted at high-performance embedded graphics image processing and GPU general computing processing (GPGPU) applications.
-
product
6.5 Digit DMM / Digitizer PXI Card
GX2065
The GX2065 offers a unique combination of features, resolution, accuracy and speed in a compact, single slot 3U PXI format. Featuring 6- digit resolution, 0.005% basic DCV reading accuracy and up to 3,500 reading per second (rps) assures you of measurements that are accurate, fast and repeatable. All measurement functions including digitizing functions are isolated from the PXI bus - providing the ability to make true differential, floating measurements. An on-board controller performs all necessary DMM and digitizer calculations, minimizing PXI control bus overhead.
-
product
RS232/422 Strobe Mux III Card & Panel
9565-16
16 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 7.6" high x 13" wide x 1" deep (193 x 330 x 25 mm).
-
product
Shuttle Bus cPCI Intelligent Interface Card
IIB-SB-CPCI
The Shuttle Bus cPCI is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, and Multiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification 84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board).In summary, this card provides all features and functions required to meet the above specification, in a cPCI platform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include for LDB_BCT, LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
product
20 Channel RF Multiplexer/Scanner PXI Card
GX6021
The GX6021 is a high-density 3U PXI switching card that provides 200 MHz bandwidth and offers four groups of 1x4 multiplexer scanners.
-
product
RS-422/485 Serial Communication Card
PCI-COM-1S
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
product
LVDT I/O Cards
CP3000
Computer Conversions Corporation
Universal AC Sensor interface digitizes up to 8 channels of individually Programmable Synchro, Resolver and LVDT/RVDT sensor inputs on a 3U cPCI (Compact PCI) and PXI Compatible plug-in circuit cardProduct allows users to interface into the widest variety of AC Position sensors all programmable within a single cardA must have for anyone using LVDT-RVDT's, Synchros and Resolver sensors or signals, electronic gauging, motion control, and instrumentation.
-
product
PCI Precision Resistor Card 9-Channel, 2Ω To 13.6kΩ
50-297-031
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
ARINC818 Cards
> ARINC818 is a specification which has become an Industry standard for the transmission of uncompressed digital video. This commercial standard uses Fibre Channel as a point-to-point communication link for low latency with the ARINC818 defining the packetized protocol for transmission of the digital video information. It is highly flexible and can be used for a variety of onboard display systems in both commercial and military applications. AIM’s ARINC818 cards use our field proven Common Core hardware design giving the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive DDR3 memory and IRIG-B time encoder/decoder functions are standard. The ARINC818 modules are available in PCIe formats.The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for ARINC818 interfaces. The dual core processor provides onboard processing and data transfer capabilities for the most demanding applications including ARINC818 support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized ARINC818 Interfaces enabling the board to analyze incoming data in real time. Each module provides 2 ARINC818 compliant ports. SFP cages make it suitable for different media types as optical or electrical network technologies. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our ARINC818 cards.
-
product
PCI 26xSPDT 2Amp Relay Card
50-131-002
The 50-131-002 26xSPDT relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
product
3U VPX Processor Card
VPX3-1260
Curtiss-Wright Defense Solutions
Optimal for high performance embedded computing (HPEC), general processing, and a variety of C5ISR applications, the VPX3-1260 rugged single board computer (SBC) delivers a fully-featured, all-in-one processing solution for your embedded system.
-
product
PCI Strain Gauge Simulator Card, 2-Channel, 1k
50-265-202
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
Mini PCI Express
MPCIE-A429
Alta Data Technologies’ MPCIE-A429 Mini PCI Express F1 interface module offers a variety of ARINC-429/575/717 channel configurations with software selectable RX/TX channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 transceiver compatible signal.
-
product
6U OpenVPX Processor Card
CHAMP-WB
Curtiss-Wright Defense Solutions
Integrating FPGAs into any system can be challenging: from ensuring your boards will meet your performance needs in the most rugged conditions to creating a basic framework that will last despite growing radar system, EW & SIGINT application needs.
-
product
VME Processor Cards
Curtiss-Wright Defense Solutions
We believe upgrading VME systems with the latest processing technology and security capabilities shouldn't require a complex and costly redesign. That's why our VME single board computers (SBCs) are designed with contemporary processors, Trusted Computing features, and pinouts that are compatible with older VME boards.
-
product
PCI Express Card
Axiomtek develops a full spectrum of PCI Express cards to help customers accelerating their design and reducing development costs.
-
product
VME Load Card
WIENER VME load boards are designed to test VME crate power supplies and fan trays by drawing power from the VME backplane and dissipating it as heat. A series of switches on the module front panel allows for easy adjustment of the current draw for each voltage channel.
-
product
PCI Card
EXC-8000PCIe104/xx
The EXC-8000PCIe104/xx card for PCI/104-Express systems supports up to four dual redundant 1760 channels using the M8K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A,B). In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
product
USB HD-SDI Video Processor/Capture Card with Overlay
2246
Video overlay up to full screen at up to 1920x1080 SDI (HD/SD) and analog inputs DVI, SDI (HD/SD), and analog outputs Prescaled SD A/V compression engine with MPEG-1/2/4 output Up/downscaling on DVI and analog outputs Captures uncompressed HD/SD frames Generates "freeze frame" video from captured frames Video "zoom" on MPEG stream and DVI output Isolated general-purpose digital I/O: 8 in / 4 out USB 2.0 interface
-
product
PCI/PCIe-Based Serial Communications Cards
PCI-C588/PCI-C584/PCIe-C588
- IRQ & IO address automatically assigned by BIOS- Supports up to 2 cards per system, jumper-less, easy to configure- Isolated RS-422/RS-485 interface (C422/C485, C518/C514)- PCI Rev 2.1 Plug-and-play- PCI Express® x1 compliant (PCIe-C588)
