XMC
An open high speed switched interconnect standard protocol extending PMC.
-
Product
XMC-PCIeStor, High Speed PCIe Single SSD Adapter
9301
-
The 9301 is a VITA 42.3 XMC adapter card / mezzanine storage module with a single M.2 SSD site. The M.2 site supports up to 4 lanes of PCIe Gen 2 connectivity at 5 Gb/s per lane when a Gen 2 or 3 capable M.2 PCIe card is used.
-
Product
XMC-to-PCI Express (PCIe) Adapter
8615
-
The Technobox, Inc. P/N 8615 XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board, and is not the low-profile version.
-
Product
Graphics Controller XMC
XMC-715
-
Curtiss-Wright Defense Solutions
The XMC-715 is an AMD E4690-based high performance graphics controller XMC designed for rugged deployed military and aerospace graphics sub-systems where high-performance, low power, high reliability and small form factor are key requirements.
-
Product
8-Channel 250 MHz A/D with DDC, Kintex UltraScale FPGA - XMC
Model 71131
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Powerful Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction cooled versions available
-
Product
AMD Zynq™ UltraScale+™ MPSoC XMC Board
IC-MPS-XMCa
-
The IC-MPS-XMCa is a XMC FPGA card based on the AMD Zynq™ Ultrascale+™ ZU4CG MultiProcessor SoC.
-
Product
1-Ch 3.6 GHz or 2-Ch 1.8 GHz 12-bit A/D with DDC, Kintex UltraScale - XMC
Model 71841
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 5 GB of DDR4 SDRAM- µSync clock/sync for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Clock up to four modules with Model 7194 High-Speed Clock Generator - PMC/XMC- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
XMC mezzanine module
XMC-620
-
Curtiss-Wright Defense Solutions
The XMC-620 from Curtiss-Wright Defense Solutions is a small form factor XMC mezzanine module optimized to provide all the power and versatility of Cisco IOS running as an Embedded Services Router (ESR). Designed for mobile and airborne systems, the XMC-620 extends the power and versatility of an enterprise router to a rugged embedded platform.
-
Product
Shared Memory Network XMC Interface
XMC-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
Product
MIL-STD-1553 & ARINC XMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
XMC-MA4
Interface Module
The XMC-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
Product
XMC-to-PCI Express Adapter
4822
-
The Technobox, Inc. P/N 4822 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 4x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
XMC-to-PCI Express Adapter
4821
-
The XMC2PCE is a passive 8X XMC to PCI express carrier card which permits the use of XMC cards in PC style PCI express 1X, 2X, 4X, 8X or 16X motherboard slots.
-
Product
Mezzanine Cards
-
PMC and XMC are the quasi standard for mezzanine cards in VME systems. esd's PMC and XMC modules extend your system with a bus interface (CAN, EtherCAT, Ethernet) or an intelligent sub system (e.g. XMC-CPU/2041, PMC-CPU/440). Furthermore esd develops customized PMC and XMC modules. VME systems without PMC slot can be extended with an esd VME-PMC-Caddy or PCIe-XPIMC-Carrier board.
-
Product
TR E5x/msd, 3U OpenVPX™ with an Intel® Xeon® Processor
TR E5x/msd
-
TR E5x/msd is an Intel® Xeon® E3-1500 v5 3U OpenVPX board for enhanced processing performance within the same SWaP envelope. XMC site or front panel for DisplayPort, Ethernet, USB or serial connections. Compliant with VITA 46.11 system management.
-
Product
FMC, XMC & PMC
-
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
Product
4-Channel 200 MHz A/D with DDC, Virtex-7 FPGA - XMC
Model 71761
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Video Compression Board
ICS-8580
-
The ICS-8580 is a standalone video frame capture, compression, streaming and archiving solution in an XMC format making it an ideal solution for demanding video streaming tasks in military and aerospace applications.
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-7 FPGA - XMC
Model 71720
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with swtiched fabric interfaces- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Graphics/Video Capture Board
NVP2102A
-
The Abaco NVP2102A is a rugged XMC graphics and raw video capture card based on the NVIDIA® Pascal ™ (GP107) Quadro® P2000 GPU architecture.
-
Product
Reverse Compact XMC-to-PCI Express (PCIe) Adapter
8260
-
Our Reverse Compact XMC-to-PCI Express (PCIe) Adapter 8X (8260) permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported.
-
Product
Test Hardware
TTPSimulate XMC/PCIe
-
TTPSimulate is a high-performance test system which enables the simulation of a networked TTP system in real-time. It allows full hardware in the loop verification of a TTP unit. There are two form factors available for this product – PCIe and XMC card format. Both cards can act as four independent TTP nodes and have an IRIG-B interface for time-stamping.
-
Product
Network Interface Card
NIC10GBT
Interface Card
The NIC10GBT is a dual port 10GBase-T XMC module that brings 10GbE expandability to new and existing embedded systems with available XMC slots.
-
Product
BusTools/1553 BusTools Software Analyzer
-
Abaco Systems' BusTools-1553 is an integrated, Microsoft Windows-based, application solution for MIL-STD-1553 test, analysis and simulation. BT-1553 software harnesses the power of Abaco Systems' hardware interfaces on PCI, PCI Express, CompactPCI, PMC, ExpressCard, PCMCIA, USB, XMC, PC/104-Plus, VME and VXI platforms for simplified control over simulation, display, data logging, playback, and protocol analysis of MIL-STD-1553/1760 A and B networks.
-
Product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Modules
AXC1553-xT
-
MIL-STD-1553 Test and Simulation modules for XMC with 1 or 2 dual redundant streams plus 8 Discrete I/O’s (on Rear-I/O).*Concurrent BC, MRT (31) and Chronological/Mailbox Bus Monitor*Full Error Injection/Detection (AS4112)*Complex Triggering, Data Capture/Filtering & 100% Bus Recording*Physical Bus Replay*IRIG-B Time Encoder/Decoder*Programmable Bus Coupling, onboard Bus Network and variable Output amplitude*Full Function, Single Function and Simulator Only versions available*Drivers for Linux and Windows*Optional Databus Test and Analysis Software and RT Production Test Plan
-
Product
PCIe Adapter for XMC
PCIe4LXMCX1
-
Simple and easy to use. Install PCIe4LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position. XMC´s with up to 8 lanes can be used. The PCIe lanes to/from the XMC are routed per PCIe specifications with matched lengths and impedance control.
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for XMC
XMC-DCE
-
Avionics Interface Technologies
Dual channel, high precision Ethernet Test Instrument
-
Product
Compact XMC-to-PCI Express (PCIe) Adapter
8241
-
Our Compact XMC-to-PCI Express (PCIe) Adapter 8X (Front-Panel I/O Only) (8241) permits use of a standard VITA 42.3 air-cooled XMC in the smallest possible edge finger PCIe form factor. The length of the adapter is the length of the XMC, while the height is a standard PCIe board, not the low-profile version.
-
Product
6U CompactPCI
-
Advantech offer 6U CompactPCI CPU boards, rear transition modules, peripheral boards, and support for PMC or XMC module.
-
Product
2-Channel 200 MHz A/D with 766 DDCs, Kintex UltraScale FPGA - XMC
Model 71865
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete software radio receiver solution for extremely high-channel-count applications- Uses Xilinx Kintex UltraScale KU035 FPGAs- Two 200 MHz 16-bit A/Ds- Four wideband DDCs (digital downconverters)- Up to 762 narrowband DDCs- Sample clock generation and synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
ccXMC-Serial
-
Conduction Cooled XMC module with 16 differential IO and 12 RS-232 IO plus Spartan VI 100 FPGA. Industrial Temp. SOSA pinout. Initial design has 2 HDLC, 2 NRZ, and 3 UART ports implemented.
