Time Standards
An absolute criterion for measuring time.
See Also: Time, Time Reference, Timers, Time Interval, GPS Time, Time Code, Time Domain, Timing, Hydrogen Masers, Atomic Clocks
-
Product
Clock & Timing
-
Analog Devices clock ICs and timing solutions enable new architectures, lower development and manufacturing costs, and shorter design times. Products feature low jitter and phase noise for clock cleanup, synchronization, generation, delay, and distribution.
-
Product
Timing Modules
-
Quartzlock provides Timing Modules for network timing, reference disciplining to various input references such as 1PPS, GPS receiver and Frequency References.
-
-
Product
Primary Standards
-
Primary standards (often also referred to as mechanical dead-weight testers, pressure balances or primary pressure standards) are the most accurate reference instruments for pressure. Their functional principle is based on the physical principle of pressure = force/area. Mass pieces placed on the top of a piston-cylinder system are the source of a precisely defined force. By producing a certain (counter) pressure inside the primary standard an equilibrium is achieved: the mass pieces, including the free-running piston of the piston-cylinder system, are floating, which will lead to a very accurate pressure at the test port which measured through piston gauge technology.
-
Product
Real Time FFT Spectrum Analyzer
-
Fatpigdog's Real Time FFT Spectrum Analyzer software is intended for hobbyist and casual use only. It is not a calibrated software instrument, and therefore any results produced can not and must not be used to provide quantified spectral and power measurements for commercial, medical, military, government, or any other official use.
-
Product
Standard CW Amplifiers
-
The BT-AlphaA-CW series is a range of classAB RF power amplifiers covering the 10kHz to1MHz frequency range. Rugged, solid-state design - high reliability. Extremely high phase and amplitude stability. High linearity. In-Built Protection. Very fast blanking. Capable of pulsed operation. Competitively priced. Suitable for CW radar, communications, HF/VHF jamming, particle accelerator applications/plasma systems, plasma, RF heating and other scientific applications.
-
Product
Coating thickness XRF Standards
-
We manufacture high accuracy reference standards capable of calibrating virtually any X-Ray Fluorescence (XRF) coating thickness and composition analysis system.
-
Product
Standard Handheld Display
TW-3.0-S
-
The TW-3.0-S Standard Handheld Display is a modern, slimline, multifunctional load monitoring device which is unique to DLM. This innovative design is built with the user in mind. It has a large, high quality LCD screen which is optically bonded removing the need for a back light and improving clarity in bright sunlight. For ease of use each handheld can be given a customisable friendly name made visible on the screen to make instant identification possible. This multi featured high precision unit ensures reliable load readings while also being simple to operate. It can be used in conjunction with any DLM manufactured load cell, just look for the d+ logo on our products.
-
Product
Real Time Monitoring Of Windows Server
GSX for Windows Server
-
Monitor and troubleshoot operating systems and related applications from a single dashboard. Windows servers and services are fueling mission-critical applications, so having visibility into the status of their health and usage is essential. By continuously testing the availability and performance of the Windows server and its applications, GSX enables proactive management of the IT environment. End-to-end monitoring improves the end-user experience, reduces mean-time-to-repair, and helps administrators to prevent issues before they happen.
-
Product
Light Sources & Calibration Standards
-
Photometric Solutions International Pty Ltd
We offer a range of specialised and customised light sources for various applications.The spectral range goes from 200 nm to 40 µm.
-
Product
Real Time Conductivity and Temperature Sensor Package
miniCT
-
The miniCT is Valeport’s real time Conductivity and Temperature sensor package. It features high accuracy sensors combined with a robust design to make it suitable for inclusion in a variety of sensor suites, fixed site monitoring in still wells or for use on frames andbuoys, ROVs, AUVs and ASVs
-
Product
Smart Optical Time Domain Reflectometer OTDR
BD900 Series
-
Shanghai Baudcom Communication Device Co.,Ltd.
BD900 series of Optical Time Domain Reflectometer has excellent dead zone performance and wide dynamic range. There are four models to choose from and that can betterly meet the customer’s specific measurement requirements. Combined with the visual fault locator, it can easily find the breaks, bends, splices, faulty connectors, and other causes of signal loss.
-
Product
Standard Pitch Spring Probes
-
Other than spring probes with gold plating, we have spring probe with anti-solder migration coating and plating that were developed by KITA. We also have anti-solder migration material for plunger tip. These are all included in “MARATHON” series. They have wide range of tip type for various use for every popular total length.
-
Product
Standard Slide Rail Size 3
65-051
-
Automatic release in extended position. The chassis/cabinet mounted slide rails are ultra rugged and hold significantly more weight and can withstand shock and vibration in harsh environments.
-
Product
Open Standard Module (OSM)
ROM-2860
Open Standard Module
Advantech ROM-2860 OSM 1.1 Computer-on-Module is powered by Qualcomm QCS6490/5430 SoC which includes up to Arm v8 Cortex® in combination with Andreo GPU 643 and Andreo VPU 633 graphics engine. It provides PCIe, USB 3.2, Giga Ethernet, MIPI-CSI, I2C, SPI, GPIO, PWM and eDP, DP, MIPI-DSI display for embedded applications.
-
Product
Benchtop Rubidium Frequency Standard
FS725
-
Stanford Research Systems, Inc.
The FS725 integrates a rubidium oscillator (SRS model PRS10), a low-noise AC power supply, and distribution amplifiers in a compact, half-width 2U chassis.
-
Product
Single Slot 6U, 32-bit Precision Timing Module
VME SyncClock32
-
The VME timing card is a standard board level product of Brandywine Communications. With a single slot 6U, 32 bit precision timing module, the VME card is compatible with VME computers. Precision synchronization to various inputs and convenient timing outputs to external equipment are standard on Brandywine’s VME card.
-
Product
Standard Lifetime Measurement System
Filter-Based Systems
-
*Excitation by bh ps Diode Lasers (BDS-SM or BDL-SMN Series)*Optional: fs Fiber Laser*Wavelength Selection by Filters*Detection by bh HPM-100 Hybrid Detectors*Excellent Dynamic Range*Ultra-High Time Resolution*IRF Width Down to 40 ps FWHM with HPM-100-06/07*Low Cost Detector Option: PMC-150 PMT Modules
-
Product
Standard Prod
121017/Colour
-
IEC 1010 Rating: 1000 Volts Cat III Double/Reinforced Insulation 30Amps Standard Colours: Black, Red Features: Standard 4mm socket to rear.
-
Product
Standard Type Spring Probes
-
From for bare board to for ICT, we have variety of spring probes for PCB. In addition to variety of tip type and total length, we also have receptacles that match the best to spring probes. We can also attach lead wire to the receptacles.
-
Product
GPS Time Synchronization Unit
-
Signals & Systems India Private Limited
GPS Time Server – GPS-DRM-1010 is a compact DIN rail mountable unit that synchronizes and maintains the timing and frequency requirement of power and process industry equipment using a signal obtained from different external sources such as GPS and GLONASS. It provides nanosecond accuracy when external time references are not available. It has a storage facility to store the system log file. It delivers NTP, SNTP, IRIG-B, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through a Web-based application.
-
Product
Continuous Time Interval Analyzers
GT668PXIe-15
-
GT8000IP is a 7 slot PXI chassis with a touch screen display that is best suited for bench top instrumentation.
-
Product
Calibration Standards
-
The accuracy of any spectroradiometric measurement can only be as good as that of the standard source used to calibrate the system.
-
Product
Sematech Analysis and SEMI Standards Analysis
-
Rocky Mountain Laboratories, Inc.
Rocky Mountain Laboratories, Inc. provides SEMI Standards analyses that conform to the following SEMATECH and SEMI Standards for testing of passivated 316L stainless steel components being considered for installation into a high-purity gas distribution system:SEMASPEC #90120401B-STD (SEM Analysis)SEMASPEC #90120402B-STD (EDS Analysis)SEMASPEC #90120403B-STD (XPS Analysis)SEMASPEC #91060573B-STD (Auger (AES) Analysis)SEMI F60-0306 (based on F60-0301) (XPS Analysis)SEMI F72-1102 (Auger (AES) Analysis)
-
Product
Time Domain Reflectometer
IRG 4000
-
Cable fault location with the BAUR IRG 4000. The IRG 4000 time domain reflectometer is integrated in BAUR cable fault location systems and is used in combination with the system software for locating cable faults in single and three-phase cable systems. Thanks to the novel operational concept, cable faults can be located more rapidly and easily with IRG 4000. The high-performance industrial PC and improved measurement parameters allow for a precise cable fault location in all cable types. The well-proven and continuously enhanced methods are available for the cable fault location as well as the newly developed Conditioning SIM/MIM** method which makes it even more effective and quick to locate wet cable faults that are difficult to detect. The SIM/MIM technology with 20 reflection measurements per HV pulse allows for selecting the best reflection image for a very precise determination of the fault distance.* Easy operation thanks to intuitive operational concept*Maximum precision with high resolution and sampling rate*Precise fault location methods for every type of fault
-
Product
Standard Method Compliant
-
Shimadzu System GC Analyzers are built and tested to meet the specific analysis requirements of applicable industry standards.
-
Product
Analysis In Real Time
Live Analyzer
-
Vibration Research Corporation
With Live Analyzer, you don’t have to wait until post-process to begin data analysis. View data in real-time and then pause the live stream to select, analyze, and export a section of the time waveform. Access the ObserVIEW graphing packages, employ averaging, analyze tachometer channels, and more.
-
Product
BF-Series Standard Models
-
The E-DRIV® BF-Series standard models feature an adjustable RPM setting on the tool and a selectable Soft Start mode. Engineered for high volume manufacturing applications the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The BF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
Product
Time Frequency Analysis Function
OS-0527
-
This function can evaluate transient phenomena that were difficult to capture by FFT analysis, and display clearly time change of the frequency component while maintaining its frequency resolution . The OS-0527 is equipped with STFT (Short Time Fourier Transform) and Wavelet transform.
-
Product
High Voltage Standard
HVS
-
The HVS uses precision matched resistors for high accuracy; it is a modified Park divider structure.
