EMI Receivers
measure conducted and radiated emissions for compliance to EMC standards.
See Also: EMI, RFI, Near Field Probes
-
Product
Test Receiver
NTR GNSS
-
Our primary objective is to provide a high performance and fully flexible test receiver for all types of GNSS systems. Thus, the NTR fully supports all existing navigation systems. The signal processing is fully flexible. The high performance correlation engine with up to 80 channels is implemented in a powerful set of FPGAs. Signal acquisition and tracking are realized on a high performance embedded ARM Cortex A8.Supporting up to 4 L-band frequencies in parallel, the NTR GNSS test receiver supports all current GNSS transmission frequencies. Due to its plug-in design, the RF front-end can easily be customized for special filtering and other frequencies.
-
Product
Digital Receivers
-
Pentek's digital receiver products cover an extensive range of signal bandwidths. Most of the receiver boards are equipped with Xilinx FPGAs and are supported with Navigator and GateFlow FPGA Design Kit (FDK).
-
Product
PCI Express Receiver Board
AD12-2000-IRIGB
-
The AD12-2000-IRIGB is a high performance wideband 0.3-1.8GHz PCIe-bus receiver on a single PCIe Gen3 board, that can continuously digitize a wide portion of the RF spectrum, with a 3.6GSPS 12-bit A/D that can be synchronized with stability of better than +/- 100 picoseconds with respect to an IRIG-B 1PPS signal and global time codes from a satellite receiver or local site time reference. Designed for demanding military, scientific, industrial, communications, safety and electrical power utility applications, the AD12-2000-IRIGB has 60dB of gain adjust range (manual and AGC with programmable loop bandwidth), a wideband noise figure of 9dB, +11dBm 1dB compression point, and 2dB peak-to-peak ripple over the 300MHz to 1.6GB frequency spectrum.
-
Product
Thermocouple, Module, Receiver, 90 Series, 64 Position
510104133
Receiver Module
Primary mating module 510108124. (May mate with other ITA modules, as well.)
-
Product
Protective Cover, G20x, Receiver, EMI
310113693
Protective Cover
G20x offers the features of the G20 system, and adds an additional 8 modules in an extended tier for higher I/O needs. This solution uses 6.75" Series Pull-Thru Adapters.
-
Product
Plus Radio Ethernet Receiver
ACSRF-4040
-
The Plus Radio Ethernet receiver is required as part of the Tinytag Radio Data Logging System. It controls the transmission of data to and from the radio loggers: data received from the loggers is then sent to the computer for viewing with Tinytag Explorer radio software. If power to the computer running the system is lost, the receiver has a battery back-up which will maintain the mesh network until power is restored. This receiver plugs directly into a LAN removing the need for a computer in the area where monitoring is to take place. The receiver is powered using a plug-in Power over Ethernet adaptor (ACS-0041) which is supplied with the unit.
-
Product
Receiver
vLoc3-Pro
-
The vLoc3-Pro utility locator introduces new innovative tools for locating buried utilities assuring damage prevention while gathering information for analysis. With two sets of screened 3D antennas signal distortion is easily detected and displayed on the bright full color display. Along with classic locate screens the vLoc3 series locators offer new locate perspective screens of Vector Locate for fully automatic non-walk over locating, Transverse Graph showing both peak and null simultaneously providing immediate measurement of signal distortion, Plan View showing the relative orientation of the cable at any angle, and a new graphical Sonde screen with guidance arrows leading to the sonde location even when it is vertical.
-
Product
Airborne Receivers & Bit Synchronizers
-
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
Product
Free Space Optical Receivers
-
These optical receivers have bandwidths in the DC to GHz range for detecting high speed free space optical signals with the lowest noise and cleanest responses possible.
-
Product
Power, Module, Receiver, CASS, 76 Position
510114107
Receiver Module
Module, ID, Cass, Signal, 76 Positions, Discrete Wiring
-
Product
Coax, Module, Receiver, CASS, 64 Position, Center PCB Mount
510113122
Receiver Module
Coax, Module, Receiver, CASS, 64 Position, Center PCB Mount.
-
Product
Receiver Systems for Monitoring, Surveillance and Logging
-
We produce complete turn-key radio monitoring systems ranging from portable single-channel applications for field tests and drive-by coverage measurements, to large scale computerized multi-channel surveillance systems capable of monitoring thousands of channels simultaneously.
-
Product
Indoor Mini Optical Receiver
SR1020
-
Hangzhou Softel Optic Co., Ltd.
Designed for FTTH(Fiber To The Home) networks ●Excellent linearity and flatness●Wide range of optical input power ●Single-mode fiber high return loss ●Using GaAs amplifier active devices ●Ultra low noise technology ●Smaller size and easier install ●Red-LED for power indication ●Color-LED for optical power indication●Double color LED for optical power indication (Non-lighted: optical power<-10dBm, Green:-10dBm
+3dBm) -
Product
Optical Receiver Stress Test
N4917BACA
-
A complete, automated, and repeatable solution for optical receiver stress test.
-
Product
100Gb/s Coherent Receiver
-
The integrated 100-Gb/s DP-QPSK receiver incorporates two 90° optical hybrids with four pairs of balanced photodetector (PD) and four linear TIAs into a single butterfly package. Unlike other technologies in which the polarization beam splitter (PBS) and/or the power splitter (BS) are not included, Optoplex’s receiver includes both of them with the optical hybrids, PDs and the TIAs to offer a fully integrated solution which will benefit users in terms of completely removing fiber routing and the skew management. The integrated receivers work at the symbol rate up to 32GBaud/s.
-
Product
Airborne Receiver
MS 2015
-
Receiver shall receive the telemetry signal transmitted by the airborne TGS unit. This unit is a single conversion super heterodyne FM receiver operating at 1486.5MHz. This unit has four connectors. They are RF input connector (J1), Power connector (J2), Signal connector (J3) for AGC signal and a Video output connector (J4). This unit operates at 28V DC and consumes a typical power of 5.6 watts.
-
Product
Receiver, S6, 6 Module
310122100
Receiver
The S6 Receiver is designed to mount to a rack or directly to a tabletop. The 1U high unit features positive-latching mechanisms and integrated guide pins to create a highly reliable engagement system. The S6 Receiver is very versatile and has module positions screened on the top for ease of module placement.
-
Product
ITA, G20x, 6.75" Series Adapters, 28 Module, EMI, 2"
410120253
ITA
ITA, G20x, 6.75" Series Adapters, 28 Module, EMI, 2"
-
Product
AC Power Line EMI Filters
CleanSweep®
-
CleanSweep® filters block EMI on power lines (both common and differential modes) and, uniquely, in ground, from reaching sensitive equipment. They also reduce EMI "backflow" from a "noisy" source that otherwise would end up on your AC power network.
-
Product
Replacement Protective Cover, I1, Receiver
310113524
Protective Cover
The receiver protective cover is designed to protect your modules and contacts while the test system is not in use. A protective cover is included with the i1 Receiver.
-
Product
Signal Chain µModule Receivers
µModule®
-
Analog Devices µModule® (micromodule) receivers consist of high performance, high speed ADCs with fixed-gain, high speed amplifiers and antialias filters. Our integrated ADC and driver products include integrated bypass capacitance and simplify the high frequency layout required to preserve ac performance. The board space savings are significant for instrumentation applications such as spectrum analyzers, oscilloscopes ,and communications test equipment, or for communications applications such as high sensitivity receivers, software-defined radio (SDR), or signal intelligence receivers. Our portfolio uses system-in-package (SiP) technology similar to multichip modules (MCM) to integrate components with different technologies, along with passive components to make an integrated subsystem.
-
Product
Synthesized UHF Belt-Pack IFB Receiver
IFBR1a
-
Wireless IFB (interruptible fold back) systems are used for talent cueing and crew communications in broadcast and motion picture production. In other cases, the IFB system is used by directors and other management to monitor program audio during a production. The IFB R1a receiver provides simplicity and flexibility in a package that is intuitive for untrained users to operate.
-
Product
Receivers
-
Designed to demodulate IRIG destruct tones, this receiver uses an up-converting superheterodyne configuration for high dynamic range and image rejection and has a receive sensitivity of better than -107 dBm. Originally developed to monitor/verify Range Safety Command Destruct Transmitters, it is a compact rugged design usable wherever a high tolerance to shock, vibration and temperature is required.
-
Product
Analog Receiver / RF Tuners
-
The Bandit™ family of analog receivers or RF tuners provide a series of high-performance, stand-alone RF downconverter modules. These products offer a low noise figure, programmable gain and a high dynamic range and ensure there are no gaps in the RF spectrum coverage.
-
Product
MIPI Receiver Test Solution
M8085A
-
The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", to TB-4304
540312010104
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", to TB-4304
-
-
Product
EMI Test Receiver
ESR
Receiver
The R&S®ESR is an EMI test receiver build to measure electromagnetic disturbances using conventional stepped scans or ultrafast FFT based time domain scans. It also functions as a powerful signal and spectrum analyzer. The receiver features real-time spectrum analysis with a wide range of diagnostic tools for detailed analysis of disturbance signals and their history.
-
Product
Extra-low Receiving Transmission Platform
9982, 9984
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai 9982(two outputs) optical receiver adopts advanced GaAs HBT ic technology, and makes the noisy power very low. When the receiving power reaches -6dBm, the system CNR is still above 50dB. 9984 four outputs extra-low receiving optical receiver, its end output port adopts 2 pieces power. Double modules that can supply 4 ways RF output.
-
Product
High Dynamic Receivers
ZRX
-
converter series with high dynamic range receivers. Typical applications are antenna measurements (OTA) and signal analysis. The ZRX Receivers are used wherever full S-parameters are not required.
