-
Product
Gigabit Ethernet Switch
VPX6-688
-
Curtiss-Wright Defense Solutions
The Curtiss-Wright VPX6-688 Gigabit Ethernet switch was designed to provide a complete networking solution for VPX systems. Suitable for a wide range of embedded computing and vehicle network applications, the VPX6-688 provides 24 ports of IEEE 802.3 compliant 1000BASE-T Gigabit Ethernet to the backplane. Optional optical interfaces provide four 1000BASE-SX Gigabit links.
-
Product
Gigabit Ethernet XMC module
IC-GIGA-XMCb
-
The IC-GIGA-XMCb is an XMC module providing up to four 10/100/1000 Ethernet channels.
-
Product
Gigabit Ethernet
CWDM SFP Transceivers
-
CWDM transceiver modules are offered at wavelengths from 1470nm to 1610nm and include LC connectors. These SFPs are 100% compatible with Cisco equipment.
-
Product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
Switch Blade
- ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch- 24-port fully managed Gigabit Ethernet switch- Pre-installed ADLINK PacketManager accelerates packet processing- Layer 2/3 switching with advanced support for VLANs, QoS and IPv6- Two 10 Gigabit Ethernet SFP+ uplink ports- Supports IPMI based on PICMG 2.9 (System Management Specification)
-
Product
Gigabit Ethernet
SFP Transceivers - Copper
-
Copper SFP transceiver modules (1000Base-T) are 100% compatible with Cisco equipment, include RJ-45 connector, and compliant with applicable industry standards.
-
Product
Gigabit Ethernet Tester
GET-100
-
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for PXI Express
PXIe-DCE
-
Avionics Interface Technologies
Supports 10/100/1000 Mbit/s Full Duplex EthernetUtilizes SFPs to support both Copper and Optical interfacesUser controlled Ethernet frame transmissions with high precision timing and scheduling
-
Product
Industrial PoE and Gigabit Ethernet Switch
GL900
-
The GL900 is a manageable Gigabit Ethernet Switch with 9-port x 1000BASE-T (4 x PoE+), AVB/TSN Protocol Stack.
-
Product
PXI-8232, Gigabit Ethernet, IEEE 488 PXI GPIB Instrument Control Module
781753-01
GPIB Controller
Gigabit Ethernet, IEEE 488 PXI GPIB Instrument Control Module—The PXI‑8232 combines a high-performance GPIB controller and a Gigabit Ethernet port into a single-slot module. You can use this module to integrate non-PXI instruments into a PXI system. The PXI‑8232 takes advantage of the Intel 82540EM Gigabit Ethernet controller. The 1,000 Mbit/s Gigabit Ethernet transfer rate provides a substantial performance increase over the Fast Ethernet transfer rate while remaining compatible with 10BASE‑T and 100BASE‑TX Fast Ethernet networks. You also can use the Ethernet port on the PXI‑8232 as an EtherCAT master, which is programmed with the NI‑Industrial Communications for EtherCAT software in LabVIEW. This module includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for XMC
XMC-DCE
-
Avionics Interface Technologies
Dual channel, high precision Ethernet Test Instrument
-
Product
IDoor Module: 2-Port Gigabit Ethernet, IEEE 802.3af (PoE) Compliant, MPCIe, RJ45
PCM-24R2PE
Card Storage Module
Meets Advantech Standard iDoor TechnologyPCI Express® Mini Card Specification Revision 1.2 compliantSupports 2 Gigabit Ethernet MAC Controller and PHY portsSupports 24 VDC input power boost up to 15.4 W at 48 VDC per PoE portSupports PoE (Power over Ethernet), IEEE 802.3af compliantPowered Device (PD) auto detection and classificationSupports IEEE 802.3u Auto-NegotiationSupports 32/64-bit Windows 7/8, Linux 2.4/2.6Supports Embedded Automation PC UNO-2400 seriesSupports Control DIN-Rail PC UNO-1300/1400 seriesSupports Control Cabinet PC UNO-3200/3300/3400 series
-
Product
Interface Board for Gigabit Ethernet
40-965-910
Interface
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
Product
3U VPX Dual-Plane Gen3/4 PCIe & 40 Gigabit Ethernet Switch
ComEth4420a
-
ComEth4420a is a cutting-edge hybrid managed switch combining PCIe Gen3/4 and 10/40 Gbs Ethernet technologies.
-
Product
PXIe-8234, 2-Port Gigabit PXI Ethernet Interface Module
780244-01
Ethernet Interface
Vision Software Included, 2-Port Gigabit PXI Ethernet Interface Module—The PXIe-8234 with Vision Acquisition Software can acquire images from the fastest GigE Vision cameras. It transfers images at full Gigabit Ethernet bandwidth on both ports simultaneously, and it is optimized for extremely low CPU load. The PXIe-8234 with Vision Acquisition Software provides full GigE Vision bandwidth at every port, giving you the bandwidth you need for your most demanding vision applications. It also includes NI Vision Acquisition Software, which is driver software for acquiring, displaying, logging, and monitoring images from a multitude of camera types. With a set of easy-to-use functions and example programs, you can quickly create applications using LabVIEW, C, C++, C#, Visual Basic, and Visual Basic .NET.
-
Product
PXIe-8238, 10 Gigabit PXI Ethernet Interface Module
784976-01
Ethernet Interface
10 Gigabit PXI Ethernet Interface Module—The PXIe-8238 is a high-performance 10-Gigabit ethernet SFP+ interface for PXI Express based on the Intel 82599 10Gb ethernet controller. It includes two 10-Gigabit ethernet SFP+ ports in a single-slot PXI Express module and is compatible with both copper and fiber optic cabling.
-
Product
10GbE Gigabit Ethernet Switch/Router
VPX3-683
-
Curtiss-Wright Defense Solutions
Enabling the vision of net-centric operations and extending the reach of transformational networks, the VPX3-683 Fireblade is a GbE multi-layer switch that is ideally suited for building Intra-Platform Networks (IPNs) for air, land, and sea vehicles or ground stations.
-
Product
100 Gigabit Ethernet Rugged Rackmount Recorder
Talon RTR 2757
-
- Designed for data capture from Pentek Quartz® RFSoC products' 100 Gigabit Ethernet ports- Single QSFP28 port with MPO transceiver- Real-time record rates up to 12.5 GB/s (100 Gigabits/s)- Front-panel removable solid state storage up to 122 TB- Dual Intel Xeon® Gold processors with up to 4 TB of DDR4 SDRAM- 4U 19-inch industrial grade server chassis- Supports up to four independent UDP streams- SystemFlow software GUI with Signal Viewer analysis tool- C-callable API for integration
-
Product
FMC for Data Communication Dual 1 Gigabit Ethernet FMC
FMC431
-
Sundance Multiprocessor Technology Ltd.
The FMC431 is a dual 1 Gigabit Ethernet FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC431 offers a High Pin Count connector but is compatible with FPGA carrier cards with Low Pin Count connectors. The Ethernet interface (1000BASE-T) is either implemented using RGMII (Low Pin Count compatible) or SGMII (High Pin Count compatible). The FMC431 also offers the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC431, thus offering users with the ability to build a complete data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card. The FMC431 is an ideal solution to bring Ethernet connectivity to an FPGA based system and ensure reliable external communication.
-
Product
3U CompactPCI® 2/4-Port Gigabit Ethernet Card
cPCI-3E10/3E12
Ethernet Interface
The cPCI-3E10 Series is 3U CompactPCI Gigabit Ethernet peripheral card equipped with Intel® 82574L PCIe Gigabit Ethernet controllers. The cPCI-3E10 provides four GbE ports on the front panel (RJ-45) with two switchable to the rear transition module, the cPCI-3E12 provides two GbE ports on the front panel (RJ-45), and the cPCI-3E10-SUB provides two Fast Ethernet ports on the front panel (DB-9). An optional Rear Transition Module (cPCI-R3E10) is available to provide rear access to the GbE ports switched from the cPCI-3E10 front panel.
-
Product
XMC Gigabit Ethernet Boards
-
High-performance 1/10-Gigabit Ethernet interface solutions for real-time and COTS data streaming applications. XMC modules provide a rugged, embedded computing platform for high-speed data communication in defense, aerospace, and industrial systems. Implementing a TCP offload engine (TOE processor) fully in hardware relieves the CPU from TCP/IP overhead and frees it to perform other tasks.
-
Product
Net Series 1 Gigabit Ethernet
-
The standard NET Series design uses rugged stainless steel connector bodies with a naval bronze engaging nut. The use of metal key and Acme threads on the mating interface allows for easy mating and un-mating of the connectors, no matter where they are located. In addition to the contact spacing, which is optimized for this application, one of the keys to achieving the 1 Gbit/s transmission rates is in the unique terminations for both the cable and bulkhead connectors. These cable terminations can be performed at a number of the Teledyne Oil & Gas worldwide manufacturing and support locations.
-
Product
10 Gigabit Ethernet Switch
VPX3-687
-
Curtiss-Wright Defense Solutions
The VPX3-687 is a versatile and high-performance Ethernet switch designed to connect the next generation of 3U systems. Offering performance without compromises, the VPX3-687 provides switching throughput of up to 320 Gbps and full line-rate forwarding of up to 32 x 10 GbE or 8 x 40 GbE interfaces.
-
Product
Gigabit Ethernet Switch
VME-690
-
Curtiss-Wright Defense Solutions
The VME-690 from Curtiss-Wright is a fully-featured Gigabit Ethernet Switch designed to provide a complete networking solution for VME systems.
-
Product
GAOTek Handheld Gigabit Ethernet Test Module
A0070008tek
-
GAOTek Handheld Gigabit Ethernet test module is a highly efficient test instrument which designed for Ethernet layout and integration tests which conforms to Ethernet test standards. This instrument is required for testing from physical layer to service layer of emerging (or next generation) networks. The Ethernet tester is the new Ethernet tester to qualify Ethernet service over LAN and RAN deployment. This is a highly efficient test instrument for service providers to ensure SLA KPIs with the subscribers.
-
Product
8-Ports Gigabit Ethernet ITA Interface
YAV90058A
Ethernet Interface
8 RJ45 LAN connectors to VPC ITA 192 pins module
-
Product
6U VME 1/10/40 Gigabit Ethernet Switch
ComEth4071e
-
The ComEth4071e is a cutting-edge 6U VME Layer 2/3 Ethernet switch compatible with VME 64x systems, complementing IC’s Ethernet switch product line including the ComEth4070e and the ComEth4000e.
-
Product
PXI-8231, 1-Port Gigabit PXI Ethernet Interface Module
781752-01
Interface
1-Port Gigabit PXI Ethernet Interface Module—The PXI‑8231 provides a Gigabit Ethernet interface with up to 1000 Mbit/s transfers. With 1000 Mbit/s Gigabit Ethernet, you achieve a substantial performance increase over 100 Mb/s Fast Ethernet while remaining completely compatible with 10BASE‑T and 100BASE‑TX Fast Ethernet networks. The PXI‑8231 also features automatic cable polarity detection.
-
Product
Qseven V1.2 SoM Evaluation Kit With I.MX287 454 MHz (Industrial) SoC, 128MB Memory, 4GB EMMC, Gigabit Ethernet, Audio, CAN And BSP
Q7M100-100-EVK
-
*Ultra low power consumption ARM9*High flexibility Qseven v1.2 compliant design*5 UART*2 CAN*24-bit TTL LCD*10/100 Mbps Ethernet*Linux 2.6.35
-
Product
GAOTek Handheld Gigabit Ethernet Tester
A0060001tek
-
GAOTek Handheld Gigabit Ethernet tester is designed for installation and maintenance of 10 M/100 M/1000 M Ethernet networks. It combines the functions of network testing, data packet capture, traffic generation, cable testing and BER testing into one unit. It also integrates full RFC-2544 and Y.1564 tests. Featuring an ergonomic design and 5.0 inch LCD color touch screen, this Ethernet tester helps the front-line field workers to analyze the network quality and locate faults rapidly. Test results can be shown graphically and numerically.
-
Product
Gigabit Ethernet
10G Transceivers: SFP+, XFP, X2, XENPAK
-
10G transceiver modules from M2 optics are available in a range of types including SFP+, XFP, X2, and XENPAK. All types meet industry standards and we can offer Cisco-compatible along with other major brands.
