Harness Test
See Also: Harness, Test Harness, Harness Testers, Wiring Analyzers
-
-
Product
PCIe 4.0 Test Platform
PXP-400A
-
The Teledyne LeCroy PXP-400A Test Platform provides a convenient means for testing PCIe 4.0 cards with a self-contained portable and powered passive backplane. The PXP-400A provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer.
-
Product
Memory Test System
T5230
-
T5230 memory test system for NAND/NVM devices adopts a combined array architecture to achieve best-in-class cost-of-test performance for wafer test, including wafer-level burn-in (WLBI) and built-in self-test (BIST). The system can perform on-wafer test of 1,024 memory devices per test head in parallel, delivering high productivity and enabling floor space savings of up to 86%. Multiple test cells are connected per system controller in the T5230, allowing independent wafer test of each test cell. The test cells can be stored in a general multi-wafer prober while minimizing the test cell floor space, and the tester can be docked with probers in both linear and multi-stack configurations. For functional tests at a maximum test rate of 125MHz/250Mbps, the T5230 assures high timing accuracy, repeatability, and failure detection capability.
-
Product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
-
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
Product
In-Line Test System
-
With an Averna in-line test system, clients boost production/yields, catch defects invisible to the human eye, reduce equipment downtime, and ensure repeatable results.
-
Product
1' Harness, 50-Pin Male D-Sub Connector
GT97108
-
1' harness, 50-pin male D-sub connector on both ends.
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
Cables, Harnesses & Wiring Looms
-
Amfax manufacture a wide range of wiring harness solutions in a variety of styles and finishes. These wiring harnesses, or looms as they are often called, can be constructed using heat-shrink, conduit tube, braid, tape, tie-wraps or lacing cord.
-
Product
Positioning Test System
TS-LBS
-
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
Product
Test Port Cable, 1 Mm
11500J
-
The Keysight 11500J test port connector has a length of 16 cm and a frequency range of DC to 110 GHz. The 11500J integrates with the Keysight N5250A network analyzer and Keysight 8510XF network analyzer systems.
-
Product
Harness Studio
-
Harness Studio is a browser for cable harness data, that brings together electrical and mechanical CAD-data into one program. It allows to navigate through very large cable harness data sets. Main aim of Harness Studio is being a tool that is very easy to use and allowing very flexible extraction of sub data sets.
-
Product
Communication Protocol Test Harness
-
Simulate Master or Outstation Devices.Monitor Communications.Create Custom Functional Tests with any .NET programming language, Python, or Tcl/Tk scripts.Exercise a device as it will be used on the utility SCADA network.Automatically Perform Conformance Test Procedures.
-
Product
Other Test Systems
-
Your business challenges do not fit the typical mold. Your test requirements are different. Ball Systems has more than 50 years of experience in multiple industries that has exposed our team to a wide variety of testing applications. As a result, we’ve likely created a solution for a challenge similar to yours.
-
Product
Automotive Electronics Functional Test System
TS-5020
-
The Keysight TS-5020 Automotive Functional Test System is a low cost, scalable test system designed with “just-enough-test” concept for medium complexity electronic control modules, such TPMS, RKE and body electronic modules
-
Product
End of Line Test System for Automotive Seats
AS519
-
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
-
Product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
-
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
Product
PCI Express 4.0 Test Platform
-
The PCI Express 4.0 Test Platform provides a convenient means for testing PCIe 4.0 add-in cards with an internal interposer and power supplies. The Summit Z416 Test Platform provides the platform for the Summit Z416 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen4, Gen3, Gen2 or Gen1 hosts and devices. It supports SMBus and other sideband signals.
-
Product
Automotive Test Solutions
-
The testing and simulation systems from this division are used primarily in the automotive and automotive supplier industry. These are, for example, modular function-testing systems and diagnostic tools for automotive ECUs or bus communication systems for a wide variety of electronic components in automotive production. Electromechanical assemblies and entire car seats are also tested to ensure they function
-
Product
Eagle Test Systems
ETS-200T
-
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
Product
1' Harness, 78-Pin Male D-Sub Connector
GT97104
-
1' harness, 78-pin male D-sub connector on both ends
-
Product
Massively Parallel Parametric Test System
P9001A
-
The highest throughput parallel parametric test solution. 100-pin parallel measurement capability and faster single parameter measurement than Keysight 4080. Good data correlation with Keysight 4080. New per-pin parametric test unit module with all basic measurement function (voltage, current, capacitance, pulse, frequency). Easy development of parallel test plan. Easy migration from 4080 environment. Proven in 1st-tier logic foundries and memory companies.
-
Product
Light-Guided Connector Assembly | Cable & Harness Tester
CableEye Light Director System
-
Our Light Director™ system (patented) provides a computer-guided technique for assembling connectors used in aerospace, medical, and other high-reliability applications. This system uses light fibers driven by super-bright LED lamps to individually illuminate target cavities in the connector being assembled. When the technician enters the wire code printed on unconnected wires, or touches a wire connected at the other end, the CableEye software turns on the appropriate fiber, thereby causing a bright, flashing light to project from inside the target cavity guiding the technician to the proper insertion point. Correct insertion is confirmed by the elimination of light from that location, whereas insertion into an incorrect location leaves the flashing light visible.
-
Product
Test System Replication/Build-to-Print
-
Need to manufacture test stations? For more than 15 years we have sourced, assembled, tested and shipped fleets of robust, cost-effective solutions. We produce them at our high-volume facilities and deploy them around the world.
-
Product
5 ft Harness, 78-Pin Male Connector
GT96110
-
5 ft harness, 78-pin male connector on both ends
-
Product
Flash Memory Test System
T5830
-
T5830 memory tester, the latest member of its T5800 product family, optimized for testing a wide range of flash memory devices used in mobile electronic devices. The highly flexible T5830 tester has all of the capabilities needed to perform wafer sorting and final testing of price-sensitive flash memories.
-
Product
Harness Testers/Thickness Gauge
-
Our Hardness Testers/Thickness Gauges includes premium models such as the EMHT40, UTEMHT20 and UTEGEMTT2. These testers are precision instruments designed to measure the thickness or hardness of most metals. Two cost effective units - FHT801 and FHT803 are tailored to agricultural applications such as checking the ripeness of fruits and vegetables in fields/warehouses.
-
Product
VXI Digital Multiplier
4152A
-
The 4152A’s advanced features like limit testing, averaging, speed/resolution trade-offs, and fast function changes provide the high “test system” throughput required in today’s production test environments.
-
Product
PCB Test System
Circuit Wizard - CW409
-
Qmax Test Technologies Pvt. Ltd.
CW 409 –Circuit Wizard PCB Test System has all the features of QT9627 such as Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test.Maximum Digital Test Speed 10MHz in the QT9627 .It can be connected to any PC/AT or Laptop with Windows 10 operating system through USB Plug and play interface. It operates on user friendly Qmax Test Director software platform with different modes like Test Station for operator level use Test Sequencer mode for Programmer level use and Interactive Workstation mode for quick working.
-
Product
Optimize Throughput And Cost For MmWave 5G Device Functional Test
-
Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:
-
